Sherwood RD-6108 manual Tuning to preset stations, Memory Backup Function

Page 20

ENGLISH

3

Select the desired preset number (1~30) and

4

Repeat the above steps 1 to 3 to memorize

other stations.

press the MEMORY/ENTER button.

 

TUNING/PRESET

 

MEMO/ENTER

 

 

 

 

 

 

 

 

 

 

MEMORY BACKUP FUNCTION

 

When using the NUMERIC buttons on the remote

The following items, set before the receiver is turned

control.

 

 

3

 

off, are memorized.

 

 

 

 

 

 

Examples) For “3” :

 

INPUT SELECTOR settings

 

 

 

 

 

 

1 within 2 seconds

5

Surround mode settings

 

 

 

For “15” :

 

Preset stations,etc.

 

 

 

 

 

 

 

 

0

 

Note : If the electricity fails or the AC input cord is

 

For “30” :

 

The station has now been stored in the memory.

disconnected for more than 2 weeks, they are all

cleared. So you should memorize them again.

When using the NUMERIC buttons, the station is

 

 

 

 

stored automatically without pressing the

 

 

 

 

MEMORY/ENTER button.

 

 

 

 

 

A stored frequency is erased from the memory by

 

 

 

 

storing another frequency in its place.

 

 

 

 

 

If “MEM” goes off, start again from the above step 2.

 

 

 

 

Tuning to preset stations

 

2

Select the desired

TUNING/PRESET

 

 

 

 

preset number.

 

 

1

After selecting the tuner as an input

 

 

source, select the preset tuning mode.

When using the NUMERIC buttons on the remote

 

T/P MODE

 

 

 

 

control.

3

 

 

 

 

 

 

 

 

 

 

 

Examples) For “3”:

 

 

 

 

 

 

1

within 2 seconds 5

 

 

 

 

 

For “15”:

 

 

 

 

 

 

0

3 within 2 seconds

0

 

 

 

 

For “30”:

(or

)

Then “PRESET” lights up.

 

When selecting the desired preset number with the

 

 

 

 

 

 

NUMERIC buttons, the desired preset station will be

 

 

 

tuned to automatically without selecting the preset

 

 

 

tuning mode.

 

 

Listening to FM stereo broadcasts

Scanning preset stations in sequence

While listening to FM broadcasts.

FM MODE

 

 

 

 

Each time this button is pressed,

 

 

 

P.SCAN

 

 

 

 

 

 

the FM mode changes as follows;

 

 

 

 

 

Stereo mode : “ST” lights up.

 

 

 

 

 

Mono mode : “ST” goes off.

 

 

 

 

 

When FM stereo broadcasts are poor because of

The receiver will start scanning the stations in the preset

weak broadcast signals, select the FM mono mode to

sequence and each station is received for 5 seconds.

reduce the noise, then FM broadcasts are reproduced

At the desired station, press this button again to stop

in monaural sound.

 

scanning.

 

 

20

Image 20
Contents RD-6108 Unpacking and Installation IntroductionRead this Before Operating Your Unit Contents Connecting Antennas System ConnectionsAC Input Cord Front Panel Controls AUDIO/VIDEO Receiver RD-6108Remote Controls Sleep Button Input Selector ButtonsRemote Control Operation Range Loading BatteriesOperations Before operationWhen CD, Video 1~3 is selected as an Input sourceAdjusting the tonebass and treble Surround Sound Surround modesDelay time Speaker placementAdjusting the Dolby Pro Logic II parameters Enjoying Surround SoundAdjusting the speaker settings Checking the speaker settingTest tone Adjusting each channel levelAdjusting each channel level with Downmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Memory Backup FunctionDubbing the audio and video signals RecordingRecording with Tape Monitor Dubbing from video components ontoOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionRD-6108