Sherwood RD-6500 manual Tuning to preset stations, Memory Backup Function

Page 21

 

Select the desired preset number (1~30) and

4

Repeat the above steps 1 to 3 to memorize

3

other stations.

press the MEMORY/ENTER button.

 

TUNING/PRESET

 

MEMO/ENTER

 

 

 

 

 

 

 

• When using the NUMERIC buttons on the remote

 

 

control.

3

 

 

MEMORY BACKUP FUNCTION

Examples) For “3” :

 

 

 

For “15” :

1 within 2 seconds 5

The following items, set before the receiver is turned

 

 

 

off, are memorized.

 

 

 

 

For “30” :

0

 

 

• INPUT SELECTOR settings

 

 

 

• Surround mode settings

 

 

 

 

• The station has now been stored in the memory.

• Preset stations,etc.

Note : If the electricity fails or the AC input cord is

• When using the NUMERIC buttons, the station is

stored automatically without pressing the

disconnected for more than 2 weeks, they are all

MEMORY/ENTER button.

cleared. So you should memorize them again.

A stored frequency is erased from the memory by storing another frequency in its place.

If “MEM” goes off, start again from the above step 2.

 

 

 

 

Select the desired

TUNING/PRESET

Tuning to preset stations

 

2

 

 

 

preset number.

 

 

 

 

 

 

 

 

 

1

After selecting the tuner as an input

 

 

 

 

 

 

 

 

 

source, select the preset tuning mode.

• When using the NUMERIC buttons on the remote

 

T/P MODE

 

control.

 

3

 

 

 

 

 

Examples) For “3”:

 

 

 

 

 

 

 

For “15”:

1

within 2 seconds 5

 

 

 

 

 

 

 

 

 

 

 

 

For “30”:

0

3 within 2 seconds

0

 

 

 

 

 

(or

)

• Then “PRESET” lights up.

 

• When selecting the desired preset number with the

 

 

 

NUMERIC buttons, the desired preset station will be

 

 

 

tuned to automatically without selecting the preset

 

 

 

tuning mode.

 

 

 

Listening to FM stereo broadcasts

 

Scanning preset stations in sequence

• While listening to FM broadcasts.

FM MODE

 

 

 

 

 

• Each time this button is pressed,

 

 

 

 

P.SCAN

 

 

 

 

 

 

 

the FM mode changes as follows;

 

 

 

 

 

 

Stereo mode : “ST” lights up.

 

 

 

 

 

 

Mono mode : “ST” goes off.

 

 

 

 

 

 

• When FM stereo broadcasts are poor because of weak

• The receiver will start scanning the stations in the preset

broadcast signals, select the FM mono mode to reduce

sequence and each station is received for 5 seconds.

the noise, then FM broadcasts are reproduced in

• At the desired station, press this button again to stop

monaural sound.

 

scanning.

 

 

 

 

ENGLISH

21

Image 21
Contents RD-6500 Read this Before Operating Your Unit IntroductionSafety Instructions Contents System Connections English AUDIO/VIDEO Receiver RD-6500 Front Panel ControlsRemote Controls Loading Batteries Remote Control Operation RangeListening to a Program Source OperationsInput source When CD, Video 1~3 is selected as anAdjusting the tonebass and treble Surround modes Surround SoundSpeaker placement Delay timeEnjoying Surround Sound Adjusting the Dolby Pro Logic II parameters When canceling the surround mode for stereo operationChecking the speaker setting Adjusting the speaker settingsAdjusting each channel level with test Downmixing into 2 front channels Manual tuning Presetting radio stationsListening to Radio Broadcasts Memory Backup Function Tuning to preset stationsRecording Dubbing the audio and video signalsRecording with Tape Monitor Dubbing from video components ontoAdjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsRD-6500