GE JBP46, JBP47, JBP45 owner manual 5 4-Wire Power Cord Installation, Before, After

Page 33

5 4-Wire Power Cord Installation

5 4-Wire Power Cord Installation

WARNING: The neutral wire of the supply circuit is connected to the neutral terminal located in the center of the connector block. The power leads must be connected to the outside (brass colored) terminals. The 4th grounding lead must be connected

to the frame of the range with the grounding plate and grounding screw.

a Remove the 3 screws from the connector block.

	b	Remove the grounding screw and strap from the connector block middle
	b	location and the screw connection to the frame of the range.

		Insert screws through each power cord terminal ring and into connector
	c
	c	block until screw engages nut. Be certain that the center wire is connected

		to the center screw of the connector block. Tighten screws securely.
		Attach ground wire to the frame of the range.
	d	Attach ground wire to the frame of the range.
		Before			After
			Neutral terminal		Neutral terminal
					Grounding
				Ground Strap	plate
				Ground Strap
				(grounding to range)	Grounding to range
					Grounding to range

Safety Information Operating Instructions Installation Instructions Troubleshooting Tips Customer Service

33

Image 33

Contents GE Answer Center GE AppliancesOwner’s Manual JBP19 JBP21 JBP24 JBP25 JBP26 JBP30 JBP45 JBP46 JBP47Staple sales slip or cancelled check here Congratulations You Are Now Part of the GE FamilyWrite the model and serial numbers here # # Troubleshooting Tips GE & You A Service PartnershipIf You Need Service Safety InformationIMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING IMPORTANT SAFETY NOTICEor using a ventilation fan or hood WARNING ANTI-TIP DEVICESafety Information Operating SAFETY PRECAUTIONSSafety Information WHEN COOKING PORK… Instructions Troubleshooting Tips Customer ServiceOVEN SELF-CLEANING OVEN SURFACE COOKING UNITS Safety Information OperatingWe want you to remain a happy and healthy part of our GE family Customer Service Troubleshooting TipsREMEMBER… SAVE THESE INSTRUCTIONSSafety Using the surface unitsInstallation Instructions How to SetTIMER ON/OFF Using the oven controlsAUTOMATIC OVEN Light START TIME ON/OFFOVEN ON Light Oven Control SettingsPREHEATED Light Oven Temperature KnobSafety Information Using the ovenD C B A Operating InstructionsPreheating and Pan Placement Safety Information Operating Instructions Installation InstructionsHow to Set the Oven for Broiling Aluminum FoilShelf Broiling guideFirst Side FoodTo Set the Timer Using the clock and timerTo Reset the Timer To Cancel the TimerAutomatic Stop Using the timed baking and roasting featuresHow to Set a Delay Start and Automatic Stop Make sure the oven clock shows the correct time of dayFor Models with Pads and an Oven Temperature Knob For Models with Only an Oven Temperature KnobAdjust the oven thermostat-Do it yourself Troubleshooting Tips Customer ServiceBefore a Clean Cycle Using the self-cleaning ovenCustomer Service Troubleshooting How to Set the Oven for CleaningAfter a Clean Cycle How to Delay the Start of CleaningTroubleshooting Tips Customer Service Operating Instructions Installation Instructionsor any reason, be sure the anti-tip device is Care and cleaning of the rangetipping of the range and cause injury Control Panel and KnobsTo clean the inside of the door Lift-Off Oven DoorTo clean the outside of the door Do not lift the door by the handleOven Heating Elements Oven Light Replacement on some modelsOven Shelves Do not clean the bake element or the broil elementPanel to Clean Under the Range How to Remove the Storage Drawer or KickBroiler Pan & Grid To remove the storage drawerCustomer Service Troubleshooting Tips Installation Instructions Operating Instructions Safety InformationPorcelain Enamel Cooktop Lift-Up Cooktop on some modelsDrip Pans Surface Unitsflat on the drip pan when you plug it back in Do not clean the surface units in a dishwasherInstallation Instructions for future use Installation of the rangeBEFORE BEGINNING INSTALLATION Before You Begininstall in either rear corner 1 Prepare the OpeningNot less than the width 30 ″Flooring Under the Range 2 Prepare for Electrical ConnectionWhen moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood or similar material as follows 3 Power Cord Strain Relief Installation 4 3-Wire Power Cord Installation Connector block Neutral terminal Ground strap Power cordDo NOT remove ground strap connection 5 4-Wire Power Cord Installation BeforeAfter 6 3-Wire Conduit Installation NOTE ALUMINUM WIRINGa Do not connect aluminum wire to the connector block 7 4-Wire Conduit Installation 8 Anti-Tip Bracket Installation 9 Leveling the Range10 Final Check Troubleshooting Tips Before you call for service…Problem See the Using theInstructions Operating Instructions Customer Service Troubleshooting Tips InstallationSee the Adjust the oven See the Broiling guideand timer section See the Using the clockTroubleshooting Tips right as far as it will go. Turn Troubleshooting Tips Installation Instructions Operating Instructions Customer ServiceWhat Is Not Covered GE Electric Range WarrantySafety Information Operating Instructions We Will Replace, At No Charge To YouIn-Home Repair Service 800-GE-CARES Service Telephone NumbersTDD 800-TDD-GEAC Special Needs Service