GE JBP47, JBP46 6 3-Wire Conduit Installation, Note Aluminum Wiring, Installation of the range

Page 34

6 3-Wire Conduit Installation

Customer Service Troubleshooting Tips Installation Instructions Operating Instructions Safety Information

Installation of the range.

Read these instructions completely and carefully.

6 3-Wire Conduit Installation

Remove the 3 screws from the connector block. Insert bare wires between the connector block terminals and movable nuts. Tighten screws securely. Do not remove ground strap connection.

WARNING: Connector block is approved for copper wire connection only. If aluminum wire is used, see note below.

NOTE: ALUMINUM WIRING

a Do not connect aluminum wire to the connector block.

Use copper building wire rated for the correct amperage and voltage to make 3 (three) 3″ copper jumper wires. Connect wire as per Step 6 or 7 depending on number of wires.

b Splice copper wires to aluminum wiring using special connector terminals designed and UL-approved for joining copper to aluminum and follow the connector manufacturer’s recommended procedure closely.

Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes.

Screw
Connector block	Bare wire tips
Connector block terminal
Bare wire
Movable nut
Flexible cable
Bracket	Conduit
	Conduit

34

Image 34

Contents Owner’s Manual GE AppliancesGE Answer Center JBP19 JBP21 JBP24 JBP25 JBP26 JBP30 JBP45 JBP46 JBP47Congratulations You Are Now Part of the GE Family Staple sales slip or cancelled check hereWrite the model and serial numbers here # # If You Need Service GE & You A Service PartnershipTroubleshooting Tips Safety Informationor using a ventilation fan or hood IMPORTANT SAFETY NOTICEIMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING WARNING ANTI-TIP DEVICESAFETY PRECAUTIONS Safety Information OperatingSafety Information Instructions Troubleshooting Tips Customer Service WHEN COOKING PORK…OVEN SELF-CLEANING OVEN Safety Information Operating SURFACE COOKING UNITSREMEMBER… Customer Service Troubleshooting TipsWe want you to remain a happy and healthy part of our GE family SAVE THESE INSTRUCTIONSInstallation Instructions Using the surface unitsSafety How to SetAUTOMATIC OVEN Light Using the oven controlsTIMER ON/OFF START TIME ON/OFFPREHEATED Light Oven Control SettingsOVEN ON Light Oven Temperature KnobD C B A Using the ovenSafety Information Operating InstructionsHow to Set the Oven for Broiling Safety Information Operating Instructions Installation InstructionsPreheating and Pan Placement Aluminum FoilFirst Side Broiling guideShelf FoodTo Reset the Timer Using the clock and timerTo Set the Timer To Cancel the TimerHow to Set a Delay Start and Automatic Stop Using the timed baking and roasting featuresAutomatic Stop Make sure the oven clock shows the correct time of dayAdjust the oven thermostat-Do it yourself For Models with Only an Oven Temperature KnobFor Models with Pads and an Oven Temperature Knob Troubleshooting Tips Customer ServiceCustomer Service Troubleshooting Using the self-cleaning ovenBefore a Clean Cycle How to Set the Oven for CleaningTroubleshooting Tips Customer Service How to Delay the Start of CleaningAfter a Clean Cycle Operating Instructions Installation Instructionstipping of the range and cause injury Care and cleaning of the rangeor any reason, be sure the anti-tip device is Control Panel and KnobsTo clean the outside of the door Lift-Off Oven DoorTo clean the inside of the door Do not lift the door by the handleOven Shelves Oven Light Replacement on some modelsOven Heating Elements Do not clean the bake element or the broil elementBroiler Pan & Grid How to Remove the Storage Drawer or KickPanel to Clean Under the Range To remove the storage drawerPorcelain Enamel Cooktop Operating Instructions Safety InformationCustomer Service Troubleshooting Tips Installation Instructions Lift-Up Cooktop on some modelsflat on the drip pan when you plug it back in Surface UnitsDrip Pans Do not clean the surface units in a dishwasherBEFORE BEGINNING INSTALLATION Installation of the rangeInstallation Instructions for future use Before You BeginNot less than the width 1 Prepare the Openinginstall in either rear corner 30 ″2 Prepare for Electrical Connection Flooring Under the RangeWhen moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood or similar material as follows 3 Power Cord Strain Relief Installation Connector block Neutral terminal Ground strap Power cord 4 3-Wire Power Cord InstallationDo NOT remove ground strap connection Before 5 4-Wire Power Cord InstallationAfter NOTE ALUMINUM WIRING 6 3-Wire Conduit Installationa Do not connect aluminum wire to the connector block 7 4-Wire Conduit Installation 9 Leveling the Range 8 Anti-Tip Bracket Installation10 Final Check Problem Before you call for service…Troubleshooting Tips See the Using theSee the Adjust the oven Customer Service Troubleshooting Tips InstallationInstructions Operating Instructions See the Broiling guideSee the Using the clock and timer sectionProblem right as far as it will go. Turn Customer Service Troubleshooting Tips Installation Instructions Operating InstructionsSafety Information Operating Instructions GE Electric Range WarrantyWhat Is Not Covered We Will Replace, At No Charge To YouTDD 800-TDD-GEAC Service Telephone NumbersIn-Home Repair Service 800-GE-CARES Special Needs Service