GE 164D2966P053, JGSC12 operating instructions Long k chain

Page 25

—

Before placing range in the counter, notice the location of the stability bracket which is already attached to the back of the range. This location should work for most installations. However, it may be more convenient to hook the stability chain to the unit when the stability bracket is attached to the upper set of holes in the back of the range. See Fig. A. The upper level set of holes are intended for use with a backsplash kit. If the backsplash is not being used, make sure that there are no structural supports for the countertop which w’ill interfere with the stability bracket when located in the upper set of holes.

auard

Bracket

Optional

Location

nback

2. Fasten one end of

o

Chain

 

the stability chain to

\

 

the floor o; wall with

 

 

 

the long screw and

Washer and

 

washer supplied. See

 

Screw

 

Fig. B. Make certain

 

 

 

the screw is going

 

A’4

into the wall ~late at

L

the base of the wall or one of the studs in the base of the wall. See Fig. C. Whether you attach the chain to the wall or floor, be certain that the screw is in at least 3/4 inch thickness of wood other than baseboard and that there are no electrical wires or plumbing in the area which the screw could penetrate. Attach the stability chain in a location which will allow the chain to be in line with the bracket side to aide as much as possible when attached to the unit. Test to see if the chain is securely fastened by tugging on the chain.

@II

Long k <chain

 

Wall Plate

 

Screw

--../

 

 

 

 

 

 

 

 

 

 

Washer = ,

 

 

 

 

\

k

 

 

 

 

 

 

 

 

 

 

3.Temporarily attach the loose end of the chain to the rear of the countertop with the tape from the packaging. See Fig. D.

4.Place the range in the counter cutout leaving just enough room between the back of the range and the wall to reach the stability bracket.

5.Hook the loose end of the chain onto the bracket by slipping the nearest link of the chain into the slot in the bracket. See Fig. A and make sure the chain is pulled as tight as possible and that there is no excess slack in the chain after the chain is attached to the bracket.

CAUTION: Excessive slack in the chain A could allow the range to tip over.

6.Slide the range all the way back into the counter. Once the range is pushed back in place, there will be a small amount of slack in the chain. This

is normal.

,-----#--, Tape

NOTE:

●If attaching to masonry, you can buy suitable screws and anchors at hardware stores. Use a masonry drill to drill the required holes.

●If range is removed for cleaning or any other reason, make sure chain is reattached.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Useand Care Guide Help US Help YOU If YOU Need ServiceUsing Your Range When You Get Your RangeInstructions Surface Cooking Always use the Lite position when ignitingAwarning Over the burner grate to support the wok. This Baking, Broiling and RoastingFlooring and Leveling Safety InstructionsFeatures of Your Range a Oa Surface Cooking HOW does this Cooktop Compare Your OLD ONE?Electric Ignition Surface Burner Controls~ Light a Surface Burner How to Select Flame SizeAfter Lighting a Burner Top-of-Range CookwareUsing Your Oven Clock and TimerShelf Positions = en ShelvesOven Vent ~ven LightBaking How to Set Your Range for BakingOven Shelves PreheatingBaking Guides PlacementCookies CakesDon’t Peek Aluminum FoilAluminum Foil Roasting Questions and AnswersRoasting Guide Frozen RoastsTse of Aluminum Foil Why are meats not turning out as brown as they should?Broiling Tips Should I salt the meat before broiling?Arrange in single layer Broiling GuideBrushed Chrome Cooktop Control Panel and KnobsLift-Up Cooktop Control knobs may be removed forClean the shelves with an abrasive cleanser or Care and CleaningRange Top Burners To replace the burnersDrip Pans Ner Grates~lft-Off Oven Door Outside of doorBroiler Pan and Rack Oven Light BulbBroiler Drawer To removePainted Surfaces Movable Oven BottomTo replace the oven bottom To protect the oven bottom surface, place aTo Clean the Continuous-Cleaning Oven Continuous-Cleaning Oven InteriorDo not scrape the porous surface with a knife Long k chain Surface Burner Air Adjustment Shutters Minor Adjustments YOU can MakeOven Burner Air Adjustment Shutter When the right amount of air flows intoYellow flames Yellow tips on inner Soft blue flames Problem Possible CauseNot Come on Problem SolverPage Page We’ll Be There Warranty

164D2966P053, JGSC12 specifications

The GE JGSC12,164D2966P053 is a state-of-the-art industrial generator set specifically designed to meet modern energy demands. Renowned for its robust performance and reliability, this generator set is a prime choice for various applications, including backup power for commercial buildings, industrial facilities, and critical infrastructure.

One of the standout features of the GE JGSC12 is its advanced power generation technology. It utilizes a high-efficiency diesel engine that is engineered for optimal fuel consumption while delivering an impressive output. This ensures that users experience lower operating costs and reduced carbon emissions, aligning with global sustainability initiatives.

The generator set is equipped with an integrated digital control system that enhances both monitoring and operational efficiency. This sophisticated system allows for real-time tracking of performance metrics, making it easier for operators to manage the generator and perform necessary maintenance. Safety features, including overload protection and automatic shutdown mechanisms, are built into the control system, ensuring that users can operate the generator with confidence.

Another notable characteristic of the GE JGSC12 is its modular design. This allows for easier transport and installation, making it suitable for a variety of applications, from construction sites to remote locations. The compact footprint ensures that it can fit into tight spaces without compromising on power output.

Additionally, the generator set's sound attenuation capabilities make it one of the quieter options on the market. This is particularly important for urban environments where noise pollution is a concern. The carefully engineered noise reduction features ensure that the generator operates without disturbing the surrounding community.

Furthermore, the GE JGSC12 has been tested for rugged reliability in extreme conditions. Whether faced with high temperatures or inclement weather, this generator set is built to withstand the elements, providing uninterrupted power when it is needed most.

In summary, the GE JGSC12,164D2966P053 is a powerful, efficient, and reliable generator set that incorporates cutting-edge technologies and features. With its sophisticated control system, modular design, and environmental considerations, it stands out as an excellent solution for a wide range of power generation needs in various sectors.
Top Page Image Contents