GE RGA620 Care and cleaning of the range, How to Remove the Range for Cleaning and Servicing

Page 18

Instructions Safety Instructions

Care and cleaning of the range.

Be sure electrical power is off and all surfaces are cool before cleaning any part of the range.

Proper care and cleaning are important so your range will give you efficient and satisfactory service. Follow these directions carefully in caring for your range to assure safe and proper maintenance.

If your range is removed for cleaning, servicing or any reason, be sure the anti-tip device is re-engaged properly when the range is replaced. Failure to take this precaution could result in tipping of the range and cause injury.

How to Remove the Range for Cleaning and Servicing

Care and Cleaning Operating

Follow these steps to remove the range for servicing or cleaning hard to reach surfaces.

Shut off the gas supply to the range.

Disconnect the electrical supply to the range.

Disconnect the gas supply tubing to the range.

Slide the range forward to free the range foot from the Anti-Tip bracket. See the Installation Instructions for the location of the bracket.

Reverse these steps to re-install the range. If the gas line has been disconnected, check for gas leaks after re-connection. See the Installation Instructions for the gas lead test method.

NOTE: A trained technician should make the gas installation, disconnection and re-connection of the gas supply to the appliance.

Tips Installation Instructions

Lift-Up Cooktop

Clean the area under the cooktop often. Built-up soil, especially grease, may catch on fire.

To make cleaning easier, the cooktop may be lifted up and propped open.

Be sure all burners are turned off before raising the cooktop. Then remove the grates.

Grasp the two front burner wells and lift the cooktop up and prop it open with the prop rod provided. Be careful of the pilots when the cooktop is up.

After cleaning underneath the cooktop with hot, soapy water and a clean cloth, hold the cooktop up, return the prop rod to its storage position and lower the cooktop until it snaps into position. Be careful not to pinch your fingers.

Consumer Support Troubleshooting

 

Burner Grates

 

Grates should be washed regularly and after

 

spillovers. Wash them in hot, soapy water and

 

rinse with clean water.

 

After cleaning, dry thoroughly by putting

 

them in a warm oven for a few minutes.

 

Don’t put the grates back on the range

 

while they are wet. When replacing the

 

grates, be sure they’re positioned securely

 

over the burners.

 

To get rid of burned-on food, place the

 

grates in a covered container (or plastic

 

bag) with 1/4 cup ammonia to loosen

18

the soil. Then scrub with a soap-filled

scouring pad if necessary.

Although they’re durable, the grates will gradually lose their shine, regardless of the best care you can give them. This is due to their continual exposure to high temperatures.

Do not operate a burner for an extended period of time without cookware on the grate. The finish on the grate may chip without cookware to absorb the heat.

Image 18
Contents 20″ and 24″ Compact Gas Ranges Important Safety Notice Operating Instructions Safety InstructionsANTI-TIP Device Page Safety Precautions Cook Meat and Poultry THOROUGHLY…Oven Surface Cooking Units Operating Instructions Care and Cleaning Installation InstructionsTroubleshooting Tips Consumer Support Flooring Under the RangeInstructions Using the surface burnersCleaning Lighting Instructions for Electric Ignition ModelsSafety How to Select Flame SizeTop of Range Cookware Power Outage-Electric Ignition Models Cleaning Operating Using the ovenInstructions Safety Instructions Consumer Support Power Outage-Standing Pilot ModelsOven Control Air AdjustmentCare and Cleaning Oven ShelvesInstructions Care and Cleaning Oven Vents Oven Shelf PositionsUsing the oven for baking Cookies Cleaning Operating Oven ShelvesTips Installation Cakes PiesHow to Set the Oven For Roasting Using the oven for roastingAdjust the oven thermostat knob-Do it yourself To Adjust the ThermostatUsing the oven for broiling Safety InstructionsHow to Set Your Oven for Broiling Broiling Guide Safety Instructions OperatingTips Installation Instructions Lift-Up Cooktop Care and cleaning of the rangeHow to Remove the Range for Cleaning and Servicing Rinse with clean waterControl Panel and Knobs Control knobs may be removed for easier cleaningBurners Metal PartsBroiler Compartment Instructions Safety Removable Oven BottomCleaning the Oven Bottom To remove the broiler panBroiler Pan and Grid Safety Lift-Off Oven DoorLet the range cool before cleaning Painted SurfacesSafety Instructions Operating Installation of the rangeFor Your Safety Instructions Troubleshooting Tips Consumer SupportCare and Cleaning Operating Instructions Tools YOU will NeedDimensions and Clearances Safety InstructionsTroubleshooting Tips Consumer Range Location Recommended gas and electric supply locationAnti-Tip Bracket Installation Instructions Anti-Tip BracketSupport Convert the Pressure Regulator Burner SpecificationsPrepare Range for Conversion Tools RequiredAdjusting the Air Shutter Converting the Surface BurnersAdjust the Oven Pilot Quality of FlamesIf the range has standing pilots Connect the Range to Gas Checking Manifold Gas PressureTips Consumer Support Electrical Grounding Instructions Operating InstructionsIf Range Has Electric Ignition Light the Oven Pilot on standing pilot modelsOven Burner Air Shutter Adjustment If adjustments are necessaryLeveling the Range Mobile Home Installation When All Hookups Are CompleteOperating Instructions Care and Cleaning Protect Your FloorBefore You Call For Service… Safety Instructions Operating Instructions Care and Cleaning Care and Cleaning Operating Instructions Safety Instructions We Will Replace Gas Range WarrantyWhat is Not Covered One YearConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio
Related manuals
Manual 36 pages 46.72 Kb

RGA624, RGA620 specifications

The General Electric (GE) RGA620 and RGA624 are advanced radiation survey meters designed for professionals in nuclear facilities, environmental monitoring, and emergency response. These devices offer robust performance and innovative features that enhance user experience and ensure precise radiation detection.

At the core of the RGA620 and RGA624 are highly sensitive Geiger-Müller (GM) tubes, which allow for the detection of alpha, beta, and gamma radiation. This versatility makes them suitable for a wide range of applications, from laboratory research to field measurements in emergency situations. Both models feature a broad energy response, enabling accurate detection across varying radiation energies.

One of the standout features of the RGA620 and RGA624 is their digital display, which provides clear and easily readable results. The intuitive interface allows users to quickly access measurement functions, change settings, and view real-time data. Alongside this, the devices are equipped with audible alarms, providing instant alerts when radiation levels exceed predefined thresholds, ensuring timely response during critical situations.

Both models utilize advanced data logging capabilities, enabling users to store measurement data for future analysis or compliance reporting. This feature is particularly valuable in regulatory environments where documentation of radiation levels is crucial. The RGA620 and RGA624 can also connect to external software for further data management, enhancing operational efficiency.

In terms of durability, the RGA620 and RGA624 are designed with rugged housing that meets stringent industrial standards. Their lightweight and portable design make them suitable for fieldwork, allowing professionals to conduct radiation surveys effortlessly. The devices are also designed for easy maintenance, with replaceable batteries and straightforward calibration processes.

Enhanced connectivity options, including USB ports, allow for easy data transfer and integration with other monitoring systems. This adaptability ensures that the RGA620 and RGA624 can be an integral part of a comprehensive radiation safety program.

Overall, the GE RGA620 and RGA624 are exemplary tools in radiation detection technology. Their combination of sensitivity, user-friendly features, and robust design make them essential for professionals working in environments where radiation monitoring is paramount. With these instruments, users can ensure safety, compliance, and effective management of radiation risks.