GE RGA620 Burner Specifications, Prepare Range for Conversion, Convert the Pressure Regulator

Page 28

Safety Instructions

Installation of the range.

Read these instructions completely and carefully.

Converting the Range for Use with LP (Propane) Gas (if necessary)

Installation Instructions Care and Cleaning Operating Instructions

Skip to Step 4 if conversion is not necessary.

This range leaves the factory set for use with natural gas. When converting to LP gas, keep these instructions in case you need to convert back to natural gas.

WARNING: This conversion must be made by a qualified installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion.

Burner Specifications:

 

Top Burner

Orifice Drill Size

Marking

 

Natural Gas

 

#53 (.0590 dia.)

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LP (Propane)

 

#66 (.0330 dia.)

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Natural Gas spud is

 

 

LP Gas spud is marked

 

 

marked with an “N”

 

 

 

with an “L”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Prepare Range for Conversion:

1.Turn off the gas supply to the range.

2.Turn off electrical power to the range.

If the range has not yet been connected to the gas supply, or if a flexible connection was made, the range may be pulled out from the wall to make the conversion easier.

CAUTION: If the gas supply to range is disconnected for any reason, see the installation instructions for proper connection and safety precautions.

Convert the Pressure Regulator:

WARNING:Do not remove the pressure regulator from the range.

1.Lift the cooktop, prop it open and locate the pressure regulator at the left rear of the range.

Gas flow

into range

Lever shown closed.

Pull to open.

Oven only shut-off.

Consumer Support Troubleshooting Tips

Tools Required:

Adjustable wrench

1/2″ open-end wrench

Phillips-head screwdriver

Flat-bladed screwdriver (blade width approximately 3/32″ across)

5/16″ nutdriver or small adjustable wrench

28

2.Use a large, flat-bladed screwdriver or a coin to remove the cap from the pressure regulator.

3.Turn the cap over and hook it into the slots. The type of gas to be used should now be visible in the center of the cap.

Natural gas cap

LP gas cap

(marked with “NAT”)

(marked with “LP”)

 

Gas flow

 

into range

Lever shown closed.

Pull to open.

Oven only shut-off.

Image 28
Contents 20″ and 24″ Compact Gas Ranges Operating Instructions Safety Instructions Important Safety NoticeANTI-TIP Device Page Safety Precautions Cook Meat and Poultry THOROUGHLY…Oven Surface Cooking Units Installation Instructions Troubleshooting Tips Consumer SupportOperating Instructions Care and Cleaning Flooring Under the RangeUsing the surface burners CleaningInstructions Lighting Instructions for Electric Ignition ModelsHow to Select Flame Size SafetyTop of Range Cookware Using the oven Instructions Safety InstructionsPower Outage-Electric Ignition Models Cleaning Operating Consumer Support Power Outage-Standing Pilot ModelsAir Adjustment Care and CleaningOven Control Oven ShelvesInstructions Care and Cleaning Oven Vents Oven Shelf PositionsUsing the oven for baking Cleaning Operating Oven Shelves Tips Installation CakesCookies PiesUsing the oven for roasting Adjust the oven thermostat knob-Do it yourselfHow to Set the Oven For Roasting To Adjust the ThermostatSafety Instructions Using the oven for broilingHow to Set Your Oven for Broiling Broiling Guide Safety Instructions OperatingCare and cleaning of the range How to Remove the Range for Cleaning and ServicingTips Installation Instructions Lift-Up Cooktop Rinse with clean waterControl knobs may be removed for easier cleaning BurnersControl Panel and Knobs Metal PartsInstructions Safety Removable Oven Bottom Cleaning the Oven BottomBroiler Compartment To remove the broiler panBroiler Pan and Grid Safety Lift-Off Oven DoorLet the range cool before cleaning Painted SurfacesInstallation of the range For Your SafetySafety Instructions Operating Instructions Troubleshooting Tips Consumer SupportCare and Cleaning Operating Instructions Tools YOU will NeedSafety Instructions Dimensions and ClearancesTroubleshooting Tips Consumer Range Location Recommended gas and electric supply locationAnti-Tip Bracket Anti-Tip Bracket Installation InstructionsSupport Burner Specifications Prepare Range for ConversionConvert the Pressure Regulator Tools RequiredAdjusting the Air Shutter Converting the Surface BurnersQuality of Flames Adjust the Oven PilotIf the range has standing pilots Checking Manifold Gas Pressure Connect the Range to GasTips Consumer Support Electrical Grounding Instructions Operating InstructionsIf Range Has Electric Ignition Light the Oven Pilot on standing pilot modelsIf adjustments are necessary Oven Burner Air Shutter AdjustmentLeveling the Range When All Hookups Are Complete Operating Instructions Care and CleaningMobile Home Installation Protect Your FloorBefore You Call For Service… Safety Instructions Operating Instructions Care and Cleaning Care and Cleaning Operating Instructions Safety Instructions Gas Range Warranty What is Not CoveredWe Will Replace One YearSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio
Related manuals
Manual 36 pages 46.72 Kb

RGA624, RGA620 specifications

The General Electric (GE) RGA620 and RGA624 are advanced radiation survey meters designed for professionals in nuclear facilities, environmental monitoring, and emergency response. These devices offer robust performance and innovative features that enhance user experience and ensure precise radiation detection.

At the core of the RGA620 and RGA624 are highly sensitive Geiger-Müller (GM) tubes, which allow for the detection of alpha, beta, and gamma radiation. This versatility makes them suitable for a wide range of applications, from laboratory research to field measurements in emergency situations. Both models feature a broad energy response, enabling accurate detection across varying radiation energies.

One of the standout features of the RGA620 and RGA624 is their digital display, which provides clear and easily readable results. The intuitive interface allows users to quickly access measurement functions, change settings, and view real-time data. Alongside this, the devices are equipped with audible alarms, providing instant alerts when radiation levels exceed predefined thresholds, ensuring timely response during critical situations.

Both models utilize advanced data logging capabilities, enabling users to store measurement data for future analysis or compliance reporting. This feature is particularly valuable in regulatory environments where documentation of radiation levels is crucial. The RGA620 and RGA624 can also connect to external software for further data management, enhancing operational efficiency.

In terms of durability, the RGA620 and RGA624 are designed with rugged housing that meets stringent industrial standards. Their lightweight and portable design make them suitable for fieldwork, allowing professionals to conduct radiation surveys effortlessly. The devices are also designed for easy maintenance, with replaceable batteries and straightforward calibration processes.

Enhanced connectivity options, including USB ports, allow for easy data transfer and integration with other monitoring systems. This adaptability ensures that the RGA620 and RGA624 can be an integral part of a comprehensive radiation safety program.

Overall, the GE RGA620 and RGA624 are exemplary tools in radiation detection technology. Their combination of sensitivity, user-friendly features, and robust design make them essential for professionals working in environments where radiation monitoring is paramount. With these instruments, users can ensure safety, compliance, and effective management of radiation risks.