GE JgB280, JgB290 manual PRoVIDE ADEqUATE GAS SUPPLy, CoNNECT the Range To GAS

Page 37

Installation Instructions

1PRoVIDE ADEqUATE GAS SUPPLy

your range is designed to operate at a pressure of 4

of water column on natural gas or, if designed for LP gas (propane or butane), 10of water column.

Make sure you are supplying your range with the type of gas for which it is designed.

This range is convertible for use on natural or propane gas. If you decide to use this range on LP gas, conversion must be made by a qualified LP installer before attempting to operate the range on that gas.

For proper operation, the pressure of natural gas supplied to the regulator must be between 4and 13of water column.

For LP gas, the pressure supplied must be between 10and 13of water column.

When checking for proper operation of the regulator, the inlet pressure must be at least 1greater than the operating (manifold) pressure as given above.

The pressure regulator located at the inlet of the range manifold must remain in the supply line regardless

of whether natural or LP gas is being used.

A flexible metal appliance connector used to connect the range to the gas supply line should have an I.D. of 1/2and be 5 feet in length for ease of installation. In Canada, flexible connectors must be single wall metal connectors no longer than 6 feet in length.

2CoNNECT THE RANGE To GAS

Shut off the main gas supply valve before disconnecting the old range and leave it off until the new hookup has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the range, the use of a CSA International-certified flexible metal appliance connector is recommended unless local codes require a hard-piped connection.

Never use an old connector when installing a new range. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.

To prevent gas leaks, put pipe-joint compound on, or wrap pipe-thread tape with Teflon* around, all male (external) pipe threads.

A. Install a manual gas line shut-off valve in the gas line in an easily accessed location outside of the range. Make sure everyone operating the range knows where and how to shut off the gas supply to the range.

B. Install male 1/2flare union adapter to the 1/2NPT internal thread at inlet of regulator. Use a backup wrench on the regulator fitting to avoid damage.

B. When installing the range from the front, remove the 90° elbow for easier installation.

C. Install male 1/2or 3/4flare union adapter to the NPT internal thread of the manual shut-off valve, taking care to back up the shut-off valve to keep it from turning.

D. Connect flexible metal appliance connector to the adapter on the range. Position range to permit connection at the shut-off valve.

E. When all connections have been made, make sure all range controls are in the off position and turn on the main gas supply valve. Use a liquid leak detector at all joints and connections to check for leaks in the system.

wARNING: Do NoT USE A FLAME To CHECK FoR GAS LEAKS.

When using test pressures greater than 1/2 psig to pressure test the gas supply system of the residence, disconnect the range and individual shut-off valve from the gas supply piping. When using test pressures of 1/2 psig or less to test the gas supply system, simply isolate the range from the gas supply system by closing the individual shut-off valve.

*Teflon: Registered trademark of DuPont

37

Image 37
Contents Write the model and serial numbers here Model # Serial # Details before attempting to install Be secured by a properly installed anti-tip bracket. SeeTo reduce the risk of tipping the range, the range must Range within 4 inches. If it does not, the bracket must beGEAppliances.com IMPORTaNT SaFeTY NOTICeAppliance as a space heater to heat or SURFaCe BURNeRS Operating Instructions Cook MeaT aND Poultry THOROUgHLY…ELeCTRIC WaRMINg DRaWeR on some models OperatingInstructions Care and CleaningSafety Using the gas surface burnersCare and Cleaning Installation Instructions Troubleshooting TipsTop-of-Range Cookware Case of Power FailureCare Safety Instructions Using the oven controlsInstallation Instructions CareOr temperature by larger amounts Safety InstructionsTouch this pad to turn the oven light on or off Touch this pad to select the broil functionBefore you begin… Troubleshooting TipsOven Vent Care and Cleaning Installation Instructions Using the upper ovenSupport Place the meat or fish on a broiler grid in a broiler pan How to Set the Oven for BroilingHi Broil To change to Lo Broil, touchCleaning Using the clock and timer. on some modelsTo Set the Timer To Set the ClockTo Cancel the Timer To Reset the TimerPower Outage Touch the Kitchen Timer On/Off pad twiceHow to Set a Delayed Start and Automatic Stop How to Set an Immediate Start and Automatic StopIf you wish to turn OFF this feature, follow the steps below Special features of your oven control. on some modelsHow to Set for Regular Baking/Roasting Using the Sabbath feature. on some modelsCare and Cleaning Installation Instructions Designed for use on the Jewish Sabbath and HolidaysTouch the Clear/Off pad How to Exit the Sabbath FeatureInstallation Troubleshooting InstructionsTips Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat on some models To Adjust the Thermostat on models with an Oven Temp KnobWhen Using the Warming Drawer Using the warming drawer. on some modelsOn Signal Light Push and turn the control knob to any desired settingTo Crisp Stale Items Temperature Selection ChartTo Warm Serving Bowls and Plates Before a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning ConsumerTo Stop a Clean Cycle on some models How to Delay the Start of Cleaning on some modelsAfter a Clean Cycle on some models Operating Care and cleaning of the rangeBurner Grates BurnersStandard Twin Burner Assemblies on some models Instructions InstallationBurner Caps and Heads Operating Instructions Tips TroubleshootingCooktop Surface Oven Air VentsLift-Off Oven Door To clean the inside of the doorOven Bottom Oven frame, pull them back outRemovable Storage Drawer on some models Removable Kick Panel on some modelsRemovable Warming Drawer on some models Lower Control Panel Front Manifold Panel and Knobs Oven Light ReplacementOven Racks Do not remove any screws to remove the coverTooLS yoU wILL Need FoR yoUR SAFETyMaterials yoU MAy Need Gas line shut-off valveInstallation Instructions DIMENSIoNS and Clearances LoCATIoN ANTI-TIP DeviceCoNNECT the Range To GAS PRoVIDE ADEqUATE GAS SUPPLyRange hookup Alternate Hookup Pressure regulator Manifold pipe Electrical CoNNECTIoNS Power cord of this appliance is equipped with aAn adapter may be used only on a 15-amp circuit Check IGNITIoN oF Surface Burners Seal the oPENINGSCheck IGNITIoN oF oVEN Burner With LP gas, some yellow tipping on outer cones is normalOther If NECESSARyWHEN ALL HooKUPS are CoMPLETED Installing the ANTI-TIP DeviceProblem Possible Causes What To Do Before you call for service…High to set a self-clean operation Oven will not self-clean Oven temperature is tooFood does not bake Oven controls improperly set Or roast properly Rack position is incorrectDuring self-clean cycle Self-clean light on Oven Temp knob has notDoor appears Self-cleaning cycle has been During the self-cleaning cycleDisplay goes blank Fuse in your home may be Power outage Power outage or surgeUnable to get Oven control pads were Display to show SF Not touched properlyLimited Time Offer! Free Shipping AccessoriesWhat GE Will Not Cover GE Will ReplaceFor The Period Warrantor General Electric Company. Louisville, KYWhat Mabe Will Not Cover Mabe Will ReplaceWarrantor Mabe Canada Inc Burlington, Ontario Consumer Support Schedule Service