GE 229C4053P447-3 1 Installing the Anti-Tip Bracket, C1 Locating The Bracket, Or Concrete

Page 8

Installation Instructions

C

Installing the Anti-Tip Bracket

C1 Locating The Bracket

The anti-tip bracket, provided with your literature and broiler pan, must be properly installed to prevent the range from tipping. Please refer to the instructions provided with your anti-tip bracket.

a.Decide whether the bracket will be installed on the right or left side of range location.

b.If the bracket side of the range has an adjacent cabinet, place the bracket against the back wall and cabinet as shown in Fig. 1. If there is a countertop overhang, offset the bracket by the amount of overhang. If there is no adjacent cabinet, place the bracket to the outside edge of the range side panel and back wall.

Adjacent Cabinet

 

Or Final Location

 

Of Range Side Panel

Wall

 

Floor-Wood

Bracket

 

Side

 

Rear

 

Leveling

Floor-Concrete

Leg

 

Fig. 1

 

C2

Installing The Bracket in Wood

or Concrete

 

INSTALLATION–WOOD CONSTRUCTION

a.Locate the centers of the four holes identified in Fig. 1 as Floor-Wood and Wall.

b.Drill a 1/8" pilot hole through the pre-marked areas. Note the angle of the wall screw in Fig. 2.

c.Mount the Anti-Tip bracket with the four screws provided.

Attachment To Wall

 

Bracket

Wall

Plate

Screw Must

Enter Wood Fig. 2

Or Metal

INSTALLATION–CONCRETE CONSTRUCTION

a.For concrete installation you will need two 1/4"x 1-1/2" lag screws, and two sleeve anchors.

b.Locate the center of the four holes identified in Fig. 1 as Floor-Concrete and Wall. Drill the recommended size holes in each.

c.Install the sleeve anchors into the predrilled concrete holes and install the lag and wall screws through the Anti-Tip bracket. Make sure the screws are securely tightened.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Tools You Will Need Parts IncludedMaterials Needed Installation Instructions For Your SafetyDo not Lift the Door by the Handle Pre- Installation ChecklistPreparing the Range COOKTOP, WALLS, and Above Cooktop Installation Required ClearancesMinimum Dimensions Between Electrical Connections Electrical Requirements B1 Making the Electrical ConnectionNEW Construction and Four Wire Cord Connection KIT Electrical ConnectionsTHREE- Wire Cord Connection KIT Installing the Anti-Tip Bracket INSTALLATION-WOOD ConstructionINSTALLATION-CONCRETE Construction C1 Locating The BracketInstalling the Range Storage Drawer RemovalFinal Check of the Anti-Tip Bracket Replacing the Oven DoorReplacing the Storage Drawer D13 D14D15 D16 If Drawer Wont CloseFinal Check List Operation Check List12229C4053P447-3

31-10463, 229C4053P447-3 1 specifications

The GE 229C4053P447-3 1,31-10463 represents a significant advancement in aerospace technology, particularly in the field of gas turbine engine components. This part is integral to ensuring the reliable and efficient operation of various aircraft systems.

One of the primary features of the GE 229C4053P447-3 is its robust design, capable of withstanding extreme temperatures and pressures encountered during flight. Manufactured using advanced alloys and composite materials, this component offers excellent durability and resistance to fatigue, significantly enhancing the lifespan of the engine. Its construction reflects GE's commitment to quality and innovation in aerospace engineering.

In terms of technologies, GE 229C4053P447-3 incorporates state-of-the-art manufacturing processes, including precision machining and advanced casting techniques. These methods ensure that each component meets stringent safety and performance standards, a critical requirement in the aviation industry. The integration of cutting-edge technologies in the design and production of this part allows for better performance metrics and operational efficiency.

A standout characteristic of the GE 229C4053P447-3 is its contribution to overall engine efficiency. The component plays a vital role in optimizing fuel combustion processes, thereby reducing emissions and operating costs. This aligns with the industry's increasing focus on sustainability and environmental responsibility. The part is engineered to enhance airflow and thermodynamic efficiency within the engine, resulting in improved thrust performance.

Furthermore, the GE 229C4053P447-3 is designed with maintenance and serviceability in mind. Its modular construction allows for easier access and replacement during routine maintenance, minimizing downtime for aircraft operators. This feature is particularly valuable for maintaining high operational readiness in commercial and military aviation sectors.

In conclusion, the GE 229C4053P447-3 1,31-10463 exemplifies GE’s innovative spirit in aerospace manufacturing. With its advanced materials, cutting-edge technologies, and focus on efficiency and longevity, this component is essential for modern aircraft engines, aligning with industry demands for performance, reliability, and sustainability. As aviation technology continues to evolve, components like the GE 229C4053P447-3 will remain at the forefront of enhancing flight capabilities and operational excellence.
Top Page Image Contents