Amana W10130752B Electrical Requirements, Gas Supply Requirements, Type of Gas, Natural gas

Page 5

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

This range is equipped with a power supply cord having a

3 prong ground plug. To minimize possible shock hazard the cord must be plugged into a grounded 3 prong outlet.

Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

This range is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized.

The wiring diagram is located on the back of the range in a clear plastic bag.

NOTE: The metal chassis of the range must be grounded in order for the control panel to work. If the metal chassis of the range is not grounded, no keypads will operate. Check with a qualified electrician if you are in doubt as to whether the metal chassis of the range is grounded.

Gas Supply Requirements

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Leak testing of the range must be conducted according to the manufacturer’s instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

This range is factory set for use with Natural gas. See “Gas Conversions” section. The model/serial rating plate located behind the broiler door on the left-hand side oven door frame has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See “Gas Conversions” section.

5

Image 5
Contents Installation Instructions 30 76.2 CM Freestanding GAS Ranges Your safety and the safety of others are very important Range SafetyLocation Requirements Installation RequirementsTools and Parts Mobile home installations require Mobile Home Additional Installation RequirementsProduct Dimensions Cabinet Dimensions Gas Supply Requirements Electrical RequirementsType of Gas Natural gasGas Supply Line Gas Supply Pressure TestingGas Pressure Regulator Burner Input RequirementsUnpack Range Installation InstructionsInstall Anti-Tip Bracket Typical flexible connection Make Gas ConnectionTypical rigid pipe connection Complete Connection Verify Anti-Tip Bracket LocationLevel Range If the low flame needs adjusting Initial lighting and gas flame adjustmentsElectronic Ignition System Check Operation of Cooktop BurnersIf the flame needs adjusting Complete InstallationIf you need Assistance or Service If range does not operate, check the followingTo Convert Gas Pressure Regulator GAS ConversionsLP Gas Conversion To Convert Oven Burner To Convert Surface BurnersNatural Gas Conversion Complete ConversionStd Burner W10130752B