Dishwasher does not drain properly
←Make sure that the cycle was complete before you opened the dishwasher. If not, allow it to complete and check again.
←Some water left in the sump area near the drain is normal.
←If the plumbing code in your area requires an air gap, make sure that it isn’t blocked or plugged.
←If the unit is connected to a garbage disposer, make sure the disposer is empty.
←If water backs up into the sink, check the garbage disposer and trap for blockage.
←Check the dishwasher filters and drain area for blockage. (See page 27.)
←Check for a kink in the drain hose.
Dishwasher does not fill properly
←Make sure the water supply is turned on.
←Make sure the dishwasher is turned on and the door is closed securely.
←Check for crimps in the water feed line.
←Make sure the water inlet filter isn’t clogged. (See page 27.)
←The system is designed to detect an overflow. When it does, it shuts off the circulation pump and turns on the drain pump. (See “Overfill Protection” on page 28.)
Dishwasher will not start
←Make sure the dishwasher is turned on and the door is closed securely.
←Make sure the Delay option is not selected.
←Check that the water supply is connected properly and the water is turned on.
←Make sure the power cord is properly plugged into the wall socket.
←Check your fuse box for a blown fuse or tripped circuit breaker.
ERROR MESSAGES ON MODELS EDW254E, EDW274E, AND EDW294E
An error will display in the LCD window if a fault occurs while a program is in progress. The table below defines each error message.
ERROR | DEFINITION |
|
|
E1 | Fill fault. Check that the main water supply is turned on. If it is, call a service technician. |
|
|
E2 | Wash and heating fault. Call a service technician. |
|
|
E4 | Water fill fault. Call a service technician. |
|
|
E5 | Drain fault. Make sure that nothing is blocking the drain and that the outlet hose isn’t kinked. If |
| that is not the case, call a service technician |
|
|
E6 | Low water fault. Check that none of the dishes have overturned and collected water. If this is |
| not the case, call a service technician. |
|
|
E7 | Alternating spray arm fault. Call a service technician. |
|
|
ERROR MESSAGES ON MODELS EDW242C
N.B.: Anomalies are signalled in the following way:
all the LEDs remain on, while the LED corresponding to the type of error flashes.
Error | When this occurs | Checks to carry out | Action to be taken |
|
|
|
|
LED 1 | During the water cycle | - Water supply valve closed | - Open the water supply valve and reset the dishwasher |
| (the program stops) | - Inlet valve filter blocked | - Check and clean the inlet valve filter if necessary |
|
| - Drain hose is kinked | - Reroute the drain hose to eliminate kinks |
|
| - Drain hose is leaking | - Call an authorized service company |
|
| - Water supply like is kinked | - Reroute the water supply line to eliminate kinks |
|
| - Insufficient water pressure | - Verify the water valve is fully open |
LED 2 | At the end | - Repeat the washing cycle | - If the same problem happens again, contact an authorized service company |
| |||
| of the cycle |
|
|
|
|
|
|
LED 5 | At the end | - The drain hose is kinked | - Reroute the drain hose to eliminate kinks |
of the cycle | - The siphon is blocked | - Check the siphon | |
| - The drain pump is clogged | - Call an authorized service company | |
LED 4 | At the end | - The filter is clogged | - Clean the filter |
of the cycle | - A pot is placed up side down | - Make sure the pot is positioned correctly during the next cycle | |
|
|
| |
|
|
|
|
ENGLISH
31