Multi Tech Equipment MVH306DSCPAS manual TRanspORTing saFeTY, EnviROnmenTaL saFeTY/deCOmmissiOning

Page 10

Safety Information

TRanspORTing saFeTY

CauTiOn

„NEVER allow any person or animal to stand underneath the equipment while lifting.

NOTICE

„Before lifting, make sure that the equipment parts (hook and vibration insulator) are not damaged and screws are not loose or missing.

„Always make sure crane or lifi tng device has been properly secured to the lifting bail (hook) of the equipment.

„ALWAYS shutdown engine before transporting.

„neveR lift the equipment while the engine is running.

„Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

„Use adequate lifting cable (wire or rope) of suffi cient strength.

„Use one point suspension hook and lift straight upwards.

„dO nOT lift machine to unnecessary heights.

„ALWAYS tie down equipment during transport by securing the equipment with rope.

enviROnmenTaL saFeTY/deCOmmissiOning

NOTICE

Decommissioning is a controlled process used to safely

retire a piece of equipment that is no longer serviceable. If the equipment poses an unacceptable and unrepairable safety risk due to wear or damage or is no longer cost effective to maintain (beyond life-cycle reliability) and is to be decommissioned (demolition and dismantlement),be sure to follow rules below:

„dO nOT pour waste or oil directly onto the ground, down a drain or into any water source.

„Contact your country's Department of Public Works or recycling agency in your area and arrange for proper disposal of any electrical components, waste or oil associated with this equipment.

„When the life cycle of this equipment is over, remove battery and bring to appropriate facility for lead reclamation. Use safety precautions when handling batteries that contain sulfuric acid.

„When the life cycle of this equipment is over, it is recommended that the trowel frame and all other metal parts be sent to a recycling center.

Metal recycling involves the collection of metal from discarded products and its transformation into raw materials to use in manufacturing a new product.

Recyclers and manufacturers alike promote the process of recycling metal. Using a metal recycling center promotes energy cost savings.

emissiOns inFORmaTiOn

NOTICE

The diesel engine used in this equipment has been designed to reduce harmful levels of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxides (NOx) contained in diesel exhaust emissions.

This engine has been certifi ed to meet US EPA Evaporative emissions requirements in the installed confi guration.

Attempting to modify or make adjustments to the engine emission system by unauthorized personnel without proper training could damage the equipment or create an unsafe condition.

Additionally, modifying the fuel system may adversely affect evaporative emissions, resulting in fi nes or other penalties.

emission Control Label

The emission control label is an integral part of the emission

system and is strictly controlled by regulations.

The label must remain with the engine for its entire life.

If a replacement emission label is needed, please contact your authorized Kohler Engine Distributor.

page 10 — mvh306ds2/dsCPAs pLATE COMPACTOR • operation and parts manual — rev. #7 (02/04/14)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Series Model MVH306DS2/ MVH306DSCPAS PROPOSITION 65 Warning Diesel engine exhaust and somePage Table of Contents Choose from three easy options Safety Information Safety MessagesGeneRaL saFeTY Engine saFeTY Before servicing equipmentBaTTeRY saFeTY eLeCTRiC sTaRT OnLY FueL saFeTY„ Use well-insulated gloves when picking up the battery EmissiOns inFORmaTiOn TRanspORTing saFeTYEnviROnmenTaL saFeTY/deCOmmissiOning Emission Control LabelSpecifications YanmarDimensions DimensionsGeneral nformation Components MVH306DS2/DSCPAS Reversible Plate Compactor ComponentsBasic engine Fuel Tank Capacity is 3.5 quarts 3.31 liters of diesel fuelChecking Engine Oil Level Using a 24 mm wrench, remove the hydraulic oil filler plugBefore Starting Checking the Hydraulic Oil LevelChecking The Fuel Checking the Air CleanerLoosen the wing nut , remove the air cleaner cover Remove the fuel cap located on top of fuel tankOperation Adjusting Handle HeightReleasing the Handle Push down decompression lever and release Recoil StartMove the throttle lever to the Start position Figure If the engine does not start, repeat steps 1 thruTraveling Normal ShutdownEmergency Shutdown Push up the handle upward until the handle locks in placeNormal Compaction Compaction Limit Compaction Sensor MVH306 Dscpas OnlySystem Diagnostics to Detect Operational Abnormalities Function to Detect Electric System AbnormalityDaily Service MaintenanceInspection and Maintenance Service Tables „„Check for leakage of fuel or oilAir Filter Every 6 Months or 400 Hours Engine Oil ReplacementReinstalling the V-belt Replacing the V-beltDraining Hydraulic Oil Vibrator Oil Level CheckDraining Vibrator Oil Adding Hydraulic OilBattery Maintenance Option Adding Hydraulic OilBattery Cable Connection Option Reinstall fuel filter and connect all associated hardwareLong Term Storage Explanation of Code in Remarks Column Suggested Spare Parts Nameplates and decals Decal Caution Decal OIL SAE 10W-30Decal Model Logo MVH-306 Decal Shell Tellus OILVibrating Plate Assy Copper Packing Vibrating PlateDrain Plug Packing 1/4 CUBase and Engine Assy Belt Cover BaseEngine ASSY. L70V6 Yanmar DUST-PROOF SpongeBase and Engine Assy Guard Hook Drain JointClamp TC-100 WASHER, Lock M14Vibrator Assy Roller Bearing NJ310EMC4 Includes Items W/ #Vibrating Case Rotary SHAFT, DriveControl Handle Assy WASHER, Flat M12 Handle BracketHandle Bracket R Rubber CouplingControl Handle Assy Handle Boss COLUMN, HandleTravel Lever Handle W/GRIP RubberHand Pump Assy Control Shaft AccumlatorIncludes Items W/# BushBattery Assy CRADLE, Battery Battery Cord 400LBattery Cord + 550L Battery 55B24LCOMPACTION Analyzing System ASSY. mVH3O6DSCPAS Wire CLIP,SENSOR Wire HARNESS, SensorWire Harness Compaction Sensor PanelElectric Device Assy Buzzer EBL Wire CPHarness C, Wire Ignition KEYYanmar L70V6 Cylinder Block Assy Ring Cylinder Block AssyCylinder Head Gasket Assy Shim SETYanmar L70V6 Cylinder head Assy Exhaust Valve Adjusting ScrewIntake Valve Valve SpringYanmar L70V6 air cleaner Assy AIR Cleaner Gasket AIR Cleaner BodyAIR Cleaner Cover Wing NUTYanmar L70V6 Muffler Assy Bolt M6X14 Plated Muffler GasketMuffler Assy Stud M8X18 PlatedYanmar L70V6 Crankshaft and Camshaft Assy Roller Tappet Assy Camshaft AssyTappet Push ROD AssyYanmar L70V6 Piston Assy Piston PIN Piston Rings SET = STDPiston Ring SET OS = CirclipYanmar L70V6 LUB OIL Pump and Governor Assy LUB. OIL Pump Cover Adjusting BoltLUB. OIL Pump Assy Ring CoverYanmar L70V6 Cooling and Starting Device Assy Side Cover a Tank GrommetSide Cover B TOP COVER, BlackYanmar L70V6 Fuel Injection Pump Assy PIN Nozzle AssyNozzle NUT Nozzle SpringYanmar L70V6 Fuel Tank and Fuel Line Assy FILTER, Fuel PackingCAP Valve Pipe GuageYanmar L70V6 Starting Motor and Dynamo Assy Armature Gear Housing AssyMagnet Switch Thrust Washer KITYanmar L70V6 TOOL, LABEL, and Gasket Assy Yanmar Label HOW to START- E LabelAIR Cooled Label Diesel LabelTerms and Conditions of Sale Parts FReighT pOLiCYPage HERE’S HOW to GET Help
Top Page Image Contents