Fisher & Paykel OR120 installation instructions Installation with a flexible hose assembly

Page 15

Installation instructions

13

Installation with a flexible hose assembly

If this appliance has to be installed with a hose assembly, the installer shall refer to the network operator or gas supplier for confirmation of the gas type, if in doubt.

When used with a flexible hose, the connector on the wall should be between 450 mm to 500

mmfrom the floor and 200 mm to 300 mm from the left-hand side of the appliance as viewed from the front. The hose connection on the appliance shall face downwards.

It is important that the hose does not come in contact with the metal of the appliance and is secured as per appropriate gas installation codes. A chain 80% of the length of the flexible gas hose must be used to prevent stress being applied to the hose. The chain should be attached securely to the product where shown, and on the wall.

Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified. The thread connection shall be Rp 1/2” (ISO 7-1) male.

Important!

After connection the installer must check that the hose is not kinked, subjected to abrasion or permanently deformed. The installer must check also that the hose is not near (or in contact) with any hot surfaces.

The hose assembly shall be as short as practicable and comply with relevant AS5601 / NZS5261 requirements.

Leak-testing and flame-testing the cooker

After installing the freestanding cooker and connecting the gas supply:

1Using a suitable leak detection fluid solution, check each gas connection one at a time by brushing the solution over the connection.

The presence of bubbles will indicate a leak. If there is a leak, tighten the fitting and then recheck for leaks.

Important!

Do not use a naked flame to test for leaks.

2Adjust the test point pressure or supply pressure to the value that is appropriate for the gas type.

3Test the operation of the appliance:

Turn on the appliance gas controls and light each burner individually and in combination. Check for a well-defined blue flame without any yellow tipping. If any abnormality is evident, then check that the burner cap is located properly and the injector nipple is aligned correctly.

Check the minimum burner setting by quickly rotating the gas control knob from the maximum to the minimum position. The flame must not go out. If you need to adjust the setting, see section ‘Adjusting the minimum burner setting’.

4If satisfacfory performance cannot be obtained, the installer shall check the installation and notify the local gas supply authority for a gas supply problem, or if it is an appliance problem, our Customer Service Centre should be called to obtain the nearest authorized Service Agent.

Image 15
Contents Installation instructions Page Contents Electrical Safety and warningsInstallation GeneralCooker must be earthed Operation Important safety precautions Installation instructions Product dimensionsFixing the backguard Rear and Side Clearances Cooker overall dimensions mmClearances Overhead ClearancesScrew/unscrew the feet to get the required height Levelling the cookerFitting the anti-tilt bracket Correctly lifting the cooker Moving the cookerLocating the area for gas and electrical connection Locating the area for gas and electrical connectionLPG Connecting the cooker to the gas supplyLeak-testing and flame-testing the cooker Installation with a flexible hose assemblyConverting to a different gas type Dual burner Replacing the injectorsSemi-rapid Triple ring wok burnerOutside crowns of dual burner Adjusting the minimum burner settingSemi-rapid and triple-ring wok burners Inside crown of dual burnerLubrication of the gas valves Table for the choice of injectorsPower supply Connecting the power supply cableInstructions Wiring diagramIntroducing your cooker Right oven controlsLeft oven controls Gas burners Using your gas cooktopUsing the dual gas burners Before using your cooktopUsing the gas burners semi-rapid and triple-ring wok Flame failure safety featureUsing the cast-iron griddle If a burner does not lightIf the flame is irregular Using the wok stand Matching cookware to burnerDiameters of pans which may be used on the cooktop Problem Cooktop troubleshootingClock display Function Temperature Control buttons Using your ovens for the first timeOven controls Illuminated symbolsButtons To set the clockBake Cooking functionsFAN Bake Using the electronic timer To set the oven for automatic cooking Automatic cookingLeft drawer Using your warmer drawerTo use the moisture selector Reversible rackCleaning the gas cooktop Care and cleaningGeneral advice Cleaning the outside of the cookerReplacing the burners Cleaning the burner parts and trivetsCorrect positioning of cap and ring triple-ring wok burner Replacing the triple-ring wok burnerReplacing the dual burners Cleaning the cast-iron griddleDrop-down grill element Cleaning the inside of your ovensCaring for the catalytic panels Cleaning the enamel cavityCleaning the fat filter When you replace the panels, make sure thatSliding shelf supports To remove the sliding shelf supportsTo re-fit the sliding shelf support onto the side racks Removing the inner and middle panes of glass Cleaning the oven door glassCare and cleaning Replacing the middle and inner panes of glass Care and cleaning Removing the oven doors Replacing the drawers Removing the drawersRemoving the oven lamp Replacing the oven lampBefore you call for service or assistance Warranty and servicePage Page NZ AU
Related manuals
Manual 48 pages 8.14 Kb Manual 52 pages 7.67 Kb Manual 48 pages 15.45 Kb

OR120 specifications

Fisher & Paykel OR120 is a versatile and high-performance range cooker designed to meet the culinary needs of both home chefs and professionals. Boasting a combination of innovative technologies and thoughtful design, the OR120 delivers exceptional cooking flexibility and efficiency, allowing users to create a variety of dishes seamlessly.

One of the standout features of the OR120 is its dual fuel configuration. This system combines the responsive heat of gas burners with the even and controlled cooking of an electric oven. This dual fuel setup offers enhanced cooking precision, ensuring that users can achieve the best results for diverse cooking techniques, from rapid boiling to slow roasting.

The OR120 features a spacious oven compartment with a generous capacity, making it ideal for preparing large meals or multiple dishes simultaneously. Equipped with multiple cooking functions, including bake, broil, and convection, the oven ensures even heat distribution for consistent cooking results. The convection feature is particularly useful, as it circulates hot air around the oven, reducing cooking times and enhancing flavor development.

For ease of usability, the OR120 comes equipped with intuitive controls and a large digital display. This user-friendly interface allows for precise temperature adjustments and cooking time settings, providing users complete control over their culinary creations. Additionally, the integrated timers and cooking progress indicators enhance the cooking experience, providing convenience and assurance.

Aesthetic appeal is another hallmark of the OR120. Its sleek design, available in a range of finishes, such as stainless steel and classic white, ensures that it complements any kitchen décor. The high-quality materials used in its construction not only enhance its durability but also make it easy to clean.

Safety is a priority in the OR120 design, with features such as flame failure protection and a cooling fan to prevent overheating. This ensures peace of mind while cooking, allowing users to focus on the task at hand.

In summary, Fisher & Paykel’s OR120 stands out as a premium choice for those seeking a combination of performance, versatility, and style in a range cooker. With features designed to enhance cooking efficiency and ease of use, it’s a valuable asset for any kitchen. Whether for everyday meals or special occasions, the OR120 can elevate the cooking experience, allowing users to explore their culinary passions with confidence.