Connect Dryer Exhaust System | Alliance Laundry Systems Dishwasher

Step 7: Connect Dryer Exhaust System

WARNING

To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors.

W604

To reduce the risk of fire and the accumulation of combustion gases, DO NOT exhaust dryer air into a window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl space under a building or concealed space of a building.

W045

WARNING

This gas appliance contains or produces a chemical or chemicals which can cause death or serious illness and which are known to the State of California to cause cancer, birth defects, or other reproductive harm. To reduce the risk from substances in the fuel or from fuel combustion, make sure this appliance is installed, operated, and maintained according to the instructions in this manual.

W115

To reduce the risk of fire, DO NOT use plastic or thin foil ducting to exhaust the dryer.

W354

•DO NOT use plastic or thin foil ducting. Rigid metal duct is recommended. Refer to Figure 21.

•Locate dryer so exhaust duct is as short as possible.

•Be certain old ducts are cleaned before installing your new dryer.

•Use 4 inch (102 mm) diameter rigid or flexible metal duct.

•The male end of each section of duct must point away from the dryer.

•Use as few elbows as possible.

•Use duct tape or pop-rivets on all duct joints. DO NOT use sheet metal screws or fasteners on exhaust pipe joints which extend into the duct and catch lint.

•Ductwork that runs through unheated areas must be insulated to help reduce condensation and lint build-up on pipe walls.

•In mobile home installations, dryer exhaust duct must be secured to mobile home structure.

•Dryer exhaust duct MUST NOT terminate under mobile home.

•Dryer exhausts 220 cfm (measured at back of dryer).

•DO NOT install flexible duct in concealed spaces, such as a wall or ceiling.

•Static pressure in exhaust duct should not be greater than .6 inches water column (1.5 cm), measured with manometer placed on exhaust duct two feet (61 cm) from dryer (check with dryer running and no load).

•Exhausting dryer in hard-to-reach locations can be done by installing 521P3 Flexible Metal Vent Kit (available as optional equipment at extra cost).

•Sufficient make-up air must be supplied to replace the air exhausted by the dryer. The free area of any opening for outside air must be at least 40 in.2 (260 cm2).

•Failure to exhaust dryer properly will void warranty.

DON’T

SWD449N

NOTE: Venting materials are not supplied with the dryer (obtain locally).

IMPORTANT: DO NOT block the airflow at the bottom of the dryer’s front panel with laundry, rugs, etc. Blockage will decrease airflow through the dryer, thus reducing the efficiency of the dryer.

Figure 21

802715

Dishwasher specifications

Alliance Laundry Systems is renowned for its commitment to quality and innovation in the field of commercial laundry and cleaning solutions. Among its impressive lineup, the Alliance Dishwasher stands out as a robust solution designed for heavy-duty performance, suited for commercial kitchens and establishments requiring efficient cleaning of dishware, glassware, and utensils.

One of the main features of Alliance Dishwashers is their exceptional cleaning capabilities. Equipped with advanced wash systems, these dishwashers effectively utilize high-pressure jets and strategically placed spray arms to ensure thorough washing, targeting every corner of the items being cleaned. The result is spotless dishes with minimal remaining contaminants, enhancing hygiene standards in any food service environment.

The technology behind Alliance Dishwashers incorporates intelligent controls that simplify operation. With user-friendly interfaces, staff can easily select from multiple washing cycles tailored to different types of loads. This versatility allows businesses to optimize energy consumption and water usage, contributing to lower operational costs while maintaining top-notch cleaning performance.

In terms of speed, Alliance Dishwashers are engineered for rapid turnarounds, often completing washing cycles in under five minutes. This feature is particularly beneficial for high-volume settings where efficiency is paramount. Additionally, many models include a built-in heat exchanger that efficiently manages water temperatures, fostering compliance with sanitation requirements and enhancing the effectiveness of the cleaning process.

Durability is another critical characteristic of Alliance Dishwashers. Constructed with high-quality stainless steel, these units resist corrosion, withstand the rigors of continual use, and maintain their appearance over time. This not only ensures longevity but also supports the maintenance of a pristine kitchen environment which is vital in the hospitality sector.

Energy efficiency is at the core of the Alliance Dishwasher design. Many models are ENERGY STAR certified, consuming less water and electricity while delivering powerful performance. This focus on sustainability not only helps businesses reduce their environmental footprint but also leads to significant cost savings.

In conclusion, the Alliance Dishwasher combines state-of-the-art technology, user-friendly features, and robust construction to meet the demands of modern commercial kitchens. From its powerful cleaning capabilities and rapid cycle times to its energy-efficient operation, the Alliance Dishwasher is an invaluable asset for any food service operation aiming for excellence in sanitation and efficiency.