Connect Fill Hoses | Alliance Laundry Systems Dishwasher specification

Step 3: Connect Fill Hoses

WARNING

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not smoke or use an open flame during this time.

W029

Water Supply

Water supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS.

Water supply faucets should be readily accessible to permit turning them off when washer is not being used.

Recommended cold water temperature is 60o to

80o Fahrenheit (16o to 27o Celsius). Recommended maximum hot water temperature is 125° Fahrenheit (51o Celsius). Warm water is a mixture of hot and cold water. Warm water temperature is dependent upon water temperature and pressure of both the hot and cold water supply lines.

WARNING

To prevent personal injury, avoid contact with inlet water temperatures higher than 125° Fahrenheit (51° Celsius) and hot surfaces.

W748

Water pressure must be a minimum of 20 to a maximum of 120 pounds per square inch (138 to 827 kPa) static pressure measured at the faucet.

NOTE: Water pressure under 20 pounds per square inch (138 kPa) will cause an extended fill time in the washer and may not properly flush out the detergent dispenser.

Turn on the water faucets and flush the lines for approximately two minutes to remove any foreign material that could clog the screens in the water mixing valve.

NOTE: When installing in newly constructed or renovated buildings, it is very important to flush the lines since build-up may have occurred during construction.

Connecting Hoses

Remove the two plain rubber washers and two filter screens from the accessories bag. Install them into each end of the fill hoses as shown in Figure 5. The screen must be facing outward.

Screw hose couplings with the filter screens onto the water faucets until they are finger-tight. Then, using a pliers, screw approximately 1/4 turn.

Screw hose couplings from other end of hoses onto the water mixing valve until they are finger-tight. Then, using a pliers, screw approximately 1/4 turn. Refer to Figure 6.

IMPORTANT: Do not cross thread or overtighten couplings. This will cause them to leak.

Turn water on and check for leaks. If leaks are found, turn off the water, unscrew hoses and reinstall them until there are no leaks.

IMPORTANT: Turn off water supply whenever there will be an extended period of non-use.

COLD

HOT

2 3

TLW1976N

1Water Faucet

2Fill Hose

3Plain Rubber Washer

4Hose Coupling

5Filter Screens

Figure 5

802715

Dishwasher specifications

Alliance Laundry Systems is renowned for its commitment to quality and innovation in the field of commercial laundry and cleaning solutions. Among its impressive lineup, the Alliance Dishwasher stands out as a robust solution designed for heavy-duty performance, suited for commercial kitchens and establishments requiring efficient cleaning of dishware, glassware, and utensils.

One of the main features of Alliance Dishwashers is their exceptional cleaning capabilities. Equipped with advanced wash systems, these dishwashers effectively utilize high-pressure jets and strategically placed spray arms to ensure thorough washing, targeting every corner of the items being cleaned. The result is spotless dishes with minimal remaining contaminants, enhancing hygiene standards in any food service environment.

The technology behind Alliance Dishwashers incorporates intelligent controls that simplify operation. With user-friendly interfaces, staff can easily select from multiple washing cycles tailored to different types of loads. This versatility allows businesses to optimize energy consumption and water usage, contributing to lower operational costs while maintaining top-notch cleaning performance.

In terms of speed, Alliance Dishwashers are engineered for rapid turnarounds, often completing washing cycles in under five minutes. This feature is particularly beneficial for high-volume settings where efficiency is paramount. Additionally, many models include a built-in heat exchanger that efficiently manages water temperatures, fostering compliance with sanitation requirements and enhancing the effectiveness of the cleaning process.

Durability is another critical characteristic of Alliance Dishwashers. Constructed with high-quality stainless steel, these units resist corrosion, withstand the rigors of continual use, and maintain their appearance over time. This not only ensures longevity but also supports the maintenance of a pristine kitchen environment which is vital in the hospitality sector.

Energy efficiency is at the core of the Alliance Dishwasher design. Many models are ENERGY STAR certified, consuming less water and electricity while delivering powerful performance. This focus on sustainability not only helps businesses reduce their environmental footprint but also leads to significant cost savings.

In conclusion, the Alliance Dishwasher combines state-of-the-art technology, user-friendly features, and robust construction to meet the demands of modern commercial kitchens. From its powerful cleaning capabilities and rapid cycle times to its energy-efficient operation, the Alliance Dishwasher is an invaluable asset for any food service operation aiming for excellence in sanitation and efficiency.