Vanguard Heating SBVRBP, SBVRBN installation manual Gas leak. See Warning statement

Page 25

OWNER’S MANUAL

TROUBLESHOOTING

Continued

WARNING: If you smell gas

•Shut off gas supply.

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating burner system where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Burner system produces unwanted odors

1.

Gas leak. See Warning statement

1.

Locate and correct all leaks (see Check-

 

 

above

 

ing Gas Connections, pages 14 and 15)

 

 

 

 

 

Burner system shuts off in use

1.

High or gusting winds

1.

Burner system has been tested for up to

 

 

 

 

40mph winds. However, extreme con-

 

 

 

 

ditions may occur. See Lighting Instruc-

 

 

 

 

tions on page 19

 

2.

Low line pressure

2.

Contact local propane/LP or natural gas

 

 

 

 

company

 

3.

Pilot is partially clogged

3.

Clean pilot (see Cleaning and Mainte-

 

 

 

 

nance, page 22)

 

4.

Inner vent pipe leaking exhaust gasses

4.

Locate and correct all leaks (see Check-

 

 

into system

 

ing Gas Connections, pages 14 and 15)

 

5.

Glass too loose and air tight gasket leaks

5.

Tighten glass

 

 

in corners after usage

 

 

 

6.

Bad thermopile

6.

Replace faulty component

 

7.

Improper vent cap installation

7.

Check for proper installation and free-

 

 

 

 

dom from debris or blockage

 

 

 

 

 

Gas odor even when control knob is in OFF

1.

Gas leak. See Warning statement

1.

Locate and correct all leaks (see Check-

position

 

above

 

ing Gas Connections, pages 14 and 15)

 

2.

Control valve defective

2.

Replace control valve

 

 

 

 

 

Gas odor during combustion

1.

Gas leak. See Warning statement

1.

Locate and correct all leaks (see Check-

 

 

above

 

ing Gas Connections, pages 14 and 15)

 

 

 

 

 

Dark residue on logs or inside of burner

1.

Improper log placement

1.

Properly locate logs (see Installing Logs,

system Note: After removing all causes of

 

 

 

Lava Rock, and Glowing Embers, page 18)

residue deposits, completely clean fireplace

2.

Air holes at burner inlet blocked

2.

Clean out air holes at burner inlets. Pe-

and appliance of all residue before reusing

 

 

 

riodically repeat as needed

appliance.

3.

Burner flame holes blocked

3.

Remove blockage or replace burner

www.desatech.com

106707

25

For more information, visit www.desatech.com

Page 24 Page 26
Image 25
Page 24 Page 26
Contents For Your Safety What to do if YOU Smell GAS For Your SafetySbvrbn and Sbvrbp Cast Iron Stove and Burner System Safety InformationProduct Identification Product FeaturesLocal Codes OperationLocation and Space Requirements PRE-INSTALLATION PreparationStove Body Assembly Cast Iron Stove and B-VENT Burner System AssemblyAttaching Stove Legs Installing Optional Blower Accessory Installing B-VENT Burner System Into Stove BodyInstalling Rear Cover Cast Iron Stove and DIRECT-VENT Burner System AssemblyInstallation Precautions Venting InstallationType B-VENT Installation Listed B-0 or Greater Installing Vent System in a Chase Installation of Listed B-1 VentChecking Vent Capacity Chimneys High Altitude InstallationRelining Systems Cast Iron Stove and B-VENT Burner System Installation Troubleshooting Venting ProblemsTion. Purchase the CSA/AGA design-certi Installation Items NeededPressure Testing Gas Supply Piping System Connecting STOVE/ Burner System to GAS SupplyPressure Testing Burner System Gas Connections Checking GAS ConnectionsInstalling Optional Wall Mounted Thermostat GWMT1 Installing Optional Wall Mount Switch GWMS2Thermostat Base Terminal W and R Installing Remote ReceiverREMOVING/REPLACING Glass Door Installing 9-Volt Battery in Hand- Held Remote Control UnitInstalling Log No Installing LOGS, Lava ROCK, and Glowing EmbersManual Lighting Procedure For Your Safety Read Before LightingOperating Stove with B-VENT Burner System Lighting InstructionsThermostat Control Operation Optional RemoteGhrc Series Operation Ghrcta Series OperationPilot Assembly Operating Optional Blower AccessoryInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatGlass Door Cleaning and MaintenancePilot and Burners LogsObserved Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Gas leak. See Warning statement Technical Service Replacement PartsWiring Diagram Service HintsAccessories SpecificationsSbvrbn Sbvrbp Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListIndicates Color Suffix Designation Amity SCIVFC* Series PSCIVFC* SeriesKEY Part Description QTY Warranty Information

SBVRBP, SBVRBN specifications

Vanguard Heating has made significant strides in the heating industry with its innovative product line, including the SBVRBN and SBVRBP models. These heating solutions are designed for both residential and commercial applications, prioritizing efficiency, durability, and advanced technology.

The SBVRBN model stands out with its high performance output, making it ideal for areas needing rapid heating. This model utilizes state-of-the-art heating elements that ensure even warmth distribution, thereby eliminating cold spots and enhancing comfort. Additionally, its compact design allows for installation in various spaces without consuming excessive floor area.

One of the standout features of the SBVRBN model is its smart technology integration. Equipped with Wi-Fi connectivity, users can easily control the temperature remotely via a smartphone app, enabling them to preheat spaces before arriving home. This feature not only enhances convenience but also contributes to energy savings, as users can adjust heating schedules according to their lifestyle.

The SBVRBP variant focuses on energy efficiency, meeting rigorous standards that result in lower energy bills. It is equipped with advanced thermostatic controls that constantly monitor and adjust the heating output based on the ambient temperature. This technology ensures that the heating system operates only when necessary, reducing unnecessary energy consumption while maintaining comfort.

Both the SBVRBN and SBVRBP models feature durable construction with high-quality materials that are designed to withstand the test of time. Corrosion-resistant components and advanced insulation techniques contribute to longevity and consistent performance. Furthermore, their quiet operation is a significant benefit, making them suitable for environments where noise is a concern, such as offices or bedrooms.

Safety is a paramount consideration in Vanguard Heating's designs. Both models are equipped with multiple safety features, including overheating protection and automatic shut-off mechanisms. These enhancements provide peace of mind for users, knowing that their heating solutions operate safely and reliably.

In summary, Vanguard Heating’s SBVRBN and SBVRBP models represent a perfect blend of innovation, efficiency, and reliability. With smart technology, energy efficiency, durable construction, and safety features, these heating solutions are designed to meet the diverse needs of modern users, making them a compelling choice in the heating market.
Top Page Image Contents