Jettech Metal Products FX-44 operation manual Adjusting the controls

Page 9

2) Turn on the machine by pressing the line button

and the machine will start to charge water. Wait for

the water to come out of the rinse arms.

Caution: if the tank door is not closed, the machine will not charge the water, so check the door by looking inside the machine baskets outlet.

3) Now the booster tank should be full, so start the quick heating of the booster. Turn off the machine, open one of the machine doors, and at the same time press buttons C and D for a few seconds until the wording Key 00 appears.

4)Go to Key 01 by pressing button C and confirm with D.

5)The wording QUIK READY NO will appear afterwards. Press C to change the status to Yes.

Keep the line button

pressed until you see this again:

. Then re-start the machine

and the quick heating will be activated. Lastly, wait until the machine is completely filled.

 

4.7 Adjusting the controls

The table below indicates the requirements and default settings of the dishwasher:

minimum washing temperature

170

°F (75°C)

minimum rinsing temperature

190

°F (88°C)

intensive washing program (speed 1)

150

racks/h

quick washing program (speed 2)

200

racks/h

Filling hose

26.4 mm (3/4")

Max. incoming water temperature

140

°F (60 °C)

Min. incoming water pressure

100 kPa (14.5 psi)

Max. incoming water pressure

345 kPa (50 psi)

Water hardness (recommended)

6 (French degrees)

Water flow rate

20 l/min. (5.3 gpm)

For viewing the temperatures and operating times:

By keeping the C button pressed for approximately 4 seconds, the instant temperature of the booster and of the tank can be viewed. The number of daily hours and of the machine's working totals of the machine’s life will also run across the display.

6

Page 8 Page 10
Image 9
Page 8 Page 10
Contents FX-44 JET-TECH Systems Corp Manufacturers Limited Warranty Maintenance InstallationIntroduction Dishwasher Handling and TransportTerminology CAP.1 IntroductionCAP.2 Dishwasher Handling and Transport CAP.3 Danger Zones and Safety MechanismsCAP.4 Installation Removal from packing and positioningElectrical connections Plumbing connections Limit switch connectionConnection to the drainage Commissioniing filling the Booster TankAdjusting the controls Adjusting the amount of rinse aid Detergent measuring device optional adjustment Commissioning the detergent and rinse aid measuring device Checks and inspections After InstallationSetting up the dishwasher for use Prevention measure recommendationsCAP.5 Dishwasher USE Using the dishwasher Periodic Maintenance to be performed at least every 20 days CAP.6 MaintenanceMachine use prec autions Operations to be performed at the end of the work cycleDOS and do Nots with the Dishwasher Self-diagnosisCAP.7 Dismantling JET-TECH Systems Garantie Limitée DU Fabricant Utilisation DU LAVE-VAISSELLE EntretienDemontage Terminologie CAP.3 Zones Dangereuses ET Mécanismes DE Sécurité CAP.2 Manutention ET Transport DU LAVE-VAISSELLERaccordements électriques Déballage et mise en placeRaccordements de plomberie Mise en service remplissage de la chaudièreRaccordement au circuit de vidange Raccordement du contacteur de fin de courseRéglage des commandes Affichage des températures et temps de fonctionnement Réglage de la quantité de liquide de rinçageDispositif de dosage du détergent option réglage Jusqu’à ce que le message Contrôles et inspections Apres Installation Recommandations concernant les mesures de protectionCAP.5 Utilisation DU LAVE-VAISSELLE Préparation à l’utilisation du lave-vaisselleMise en route du lave-vaisselle Opérations à effectuer à la fin du cycle de travail Précautions lors de l’utilisation de la machineDispositions générales CAP.6 EntretienEntretien Periodique à faire au moins tous les 20 jours Faire ET NE PAS FaireCAP.7 Demontage AutodiagnosticPage MDI 80ETL

FX-44 specifications

Jettech Metal Products has garnered a reputation for excellence in manufacturing high-quality industrial components, and their FX-44 series exemplifies this commitment. The FX-44, designed for versatility and robustness, stands out in the realm of metal products, offering innovative solutions for various industries, including automotive, aerospace, and heavy machinery.

One of the main features of the FX-44 is its remarkable strength-to-weight ratio. Constructed from advanced alloys, this product delivers superior performance without unnecessary bulk. This characteristic is especially beneficial in applications where weight reduction is crucial, such as in aerospace components, allowing for improved fuel efficiency and performance.

Another noteworthy aspect of the FX-44 is its exceptional resistance to corrosion and wear. The application of cutting-edge surface treatments significantly enhances its durability, making it suitable for use in harsh environments. This is particularly important in industries like oil and gas, where components are often exposed to corrosive substances and extreme temperatures.

The FX-44 also incorporates precision engineering techniques, ensuring tight tolerances and consistent quality throughout the manufacturing process. This attention to detail minimizes the risk of failure and increases the reliability of the components, providing peace of mind to OEMs and end-users alike.

Additionally, the FX-44 is designed with adaptability in mind. Its modular design allows for easy integration into existing systems and can be customized to meet specific client needs. This flexibility makes it a popular choice among engineers looking to optimize their projects without compromising performance or safety.

Advanced manufacturing technologies play a vital role in the production of the FX-44. Utilizing state-of-the-art CNC machining and additive manufacturing techniques, Jettech Metal Products can produce complex geometries that were previously unattainable. This capability not only enhances the design possibilities but also contributes to reduced lead times and increased production efficiency.

In summary, the Jettech Metal Products FX-44 is a testament to modern engineering and manufacturing excellence. With its superior strength-to-weight ratio, corrosion resistance, precision engineering, adaptability, and the application of advanced technologies, the FX-44 is poised to meet the demanding needs of today's industrial landscape, proving to be a reliable choice for professionals across various sectors.
Top Page Image Contents