Jettech Metal Products FX-44 CAP.4 Installation, Removal from packing and positioning

Page 7

CAP.4 INSTALLATION

4.1Removal from packing and positioning:

￿Make sure that the dishwasher is in perfect condition. In case of signs of damage, report them to the seller and haulage contractor. In case of doubt concerning the dishwasher conditions,

do not use it before having it checked by an authorised service centre.

￿The installation must be performed exclusively by qualified technicians, according to the manufacturer’s instructions.

￿Move the dishwasher where you wish to install it and remove the packing.

￿This dishwasher is designed for fixed connections only.

￿Position the dishwasher on a flat surface.

￿Install electrical, hydraulic and drain lines in the washing area according to the instructions provided on the machine's technical data sheet. Further details are indicated in the paragraphs relative to plumbing and electrical connections.

￿Before connecting the dishwasher to the water and electrical supply, make sure that the general features and data indicated by the manufacturer on the plate on the back of the manual have been complied with as far as the arrangement of the installation site is concerned.

￿The floor must be measured taking the overall weight of the machine into consideration. It must also be perfectly flat.

NOTE: to connect the dishwasher to work tops, couple the supports on the edges of the tank and fix them using the screws provided. The connection can be either on the front or side.

4.2 Electrical connections :

“The dishwasher shall be installed in accordance with local codes, or in the absence of local codes, installed in accordance with the applicable requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC), Part 1, CSA C22.1, and Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations, NFPA 96”

￿When connecting the dishwasher to the power supply, refer to the wiring diagram and the data plate of the dishwasher.

￿Make sure that the voltage and frequency of the power supply correspond to those on the plate indicating the technical characteristics located on the right side of the machine.

￿Install a “main switch” (not provided) on the electrical line that supplies the dishwasher in compliance with the requirements of the local electrical standards.

￿All the electrical connections go to the terminal block located inside the machine, then connect to the mains using a power cord (not provided) suitably sized for the load (see plate adjacent to the terminal block); the cord and plug must comply with the requirements of the local electrical standards.

￿The appliance must also be included in an equipotential system, the connection of which is performed using a

screw marked with the following symbol:

 

 

. The equipotential conductor must have a section of 10 mm².

 

 

￿An effective earthing system in conformity with the prevention standards in force is a guarantee for operator and equipment safety.

￿In the three-phase models, check for correct rotation of the wash pump.

Note: If interventions on the electric circuit must be performed, disconnect from the mains and apply a tag on the switch indicating the intervention in progress.

4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents FX-44 JET-TECH Systems Corp Manufacturers Limited Warranty Dishwasher Handling and Transport InstallationMaintenance IntroductionTerminology CAP.1 IntroductionCAP.2 Dishwasher Handling and Transport CAP.3 Danger Zones and Safety MechanismsRemoval from packing and positioning CAP.4 InstallationElectrical connections Commissioniing filling the Booster Tank Limit switch connectionPlumbing connections Connection to the drainageAdjusting the controls Adjusting the amount of rinse aid Detergent measuring device optional adjustment Commissioning the detergent and rinse aid measuring device Checks and inspections After InstallationPrevention measure recommendations Setting up the dishwasher for useCAP.5 Dishwasher USE Using the dishwasher Operations to be performed at the end of the work cycle CAP.6 MaintenancePeriodic Maintenance to be performed at least every 20 days Machine use prec autionsSelf-diagnosis DOS and do Nots with the DishwasherCAP.7 Dismantling JET-TECH Systems Garantie Limitée DU Fabricant Entretien Utilisation DU LAVE-VAISSELLEDemontage Terminologie CAP.3 Zones Dangereuses ET Mécanismes DE Sécurité CAP.2 Manutention ET Transport DU LAVE-VAISSELLERaccordements électriques Déballage et mise en placeRaccordement du contacteur de fin de course Mise en service remplissage de la chaudièreRaccordements de plomberie Raccordement au circuit de vidangeRéglage des commandes Affichage des températures et temps de fonctionnement Réglage de la quantité de liquide de rinçageDispositif de dosage du détergent option réglage Jusqu’à ce que le message Contrôles et inspections Apres Installation Recommandations concernant les mesures de protectionPréparation à l’utilisation du lave-vaisselle CAP.5 Utilisation DU LAVE-VAISSELLEMise en route du lave-vaisselle Opérations à effectuer à la fin du cycle de travail Précautions lors de l’utilisation de la machineFaire ET NE PAS Faire CAP.6 EntretienDispositions générales Entretien Periodique à faire au moins tous les 20 joursCAP.7 Demontage AutodiagnosticPage MDI 80ETL

FX-44 specifications

Jettech Metal Products has garnered a reputation for excellence in manufacturing high-quality industrial components, and their FX-44 series exemplifies this commitment. The FX-44, designed for versatility and robustness, stands out in the realm of metal products, offering innovative solutions for various industries, including automotive, aerospace, and heavy machinery.

One of the main features of the FX-44 is its remarkable strength-to-weight ratio. Constructed from advanced alloys, this product delivers superior performance without unnecessary bulk. This characteristic is especially beneficial in applications where weight reduction is crucial, such as in aerospace components, allowing for improved fuel efficiency and performance.

Another noteworthy aspect of the FX-44 is its exceptional resistance to corrosion and wear. The application of cutting-edge surface treatments significantly enhances its durability, making it suitable for use in harsh environments. This is particularly important in industries like oil and gas, where components are often exposed to corrosive substances and extreme temperatures.

The FX-44 also incorporates precision engineering techniques, ensuring tight tolerances and consistent quality throughout the manufacturing process. This attention to detail minimizes the risk of failure and increases the reliability of the components, providing peace of mind to OEMs and end-users alike.

Additionally, the FX-44 is designed with adaptability in mind. Its modular design allows for easy integration into existing systems and can be customized to meet specific client needs. This flexibility makes it a popular choice among engineers looking to optimize their projects without compromising performance or safety.

Advanced manufacturing technologies play a vital role in the production of the FX-44. Utilizing state-of-the-art CNC machining and additive manufacturing techniques, Jettech Metal Products can produce complex geometries that were previously unattainable. This capability not only enhances the design possibilities but also contributes to reduced lead times and increased production efficiency.

In summary, the Jettech Metal Products FX-44 is a testament to modern engineering and manufacturing excellence. With its superior strength-to-weight ratio, corrosion resistance, precision engineering, adaptability, and the application of advanced technologies, the FX-44 is poised to meet the demanding needs of today's industrial landscape, proving to be a reliable choice for professionals across various sectors.
Top Page Image Contents