PUR Water Purification Products PUR200, PUR210, PUR220, PUR310, PUR300 Setting Up Your Water Cooler

Page 5

3

Setting Up Your Water Cooler

SETTING UP YOUR WATER COOLER

1.DO NOT PLUG UNIT IN

2.Allow the water cooler to stand in an upright position for at least 30 minutes before turning on the power to allow all cooling refrigerant to settle.

3.Allow at least 1" of space for ventilation around the sides of the unit for air circulation and electrical connections.

4.Select a firm level floor for system away from radiators.

Pre-activating & Installing the Filter System

7. INSERT FILTER

Insert filter into filter tray by lining up the notches on the filter with the grooves in the filter tray. (See figure 9A)

When the filter has dropped into the grooves, twist the filter 45 degrees according to the arrow on the filter tray to lock and seal the filter into place. Each filter goes into the filter tray in an opposite direction. (See figure 9B)

Filter should feel snug in filter tray.

Do not try to force the filter in when it is not lined up as it may cause damage to the product.

8. FILL TANK

• Fill with cold water to the fill line and place on unit. (See figures 4 & 5)

9.ALLOW FILTRATION TO START

• Wait approximately 15 minutes.

• Plug in the power cord and turn on all 3 switches on the back of the cooler.

1 ENGLISH

HOW TO INSTALL FILTERS:

Note: Moisture may be present in the filter bag. This is to prevent the filter from drying out.

Important: Do not remove shipping retainer until cartridge has been soaked and drained. Refer to Figure #5.

1. SOAK THE FILTERS

Place each filter in a large glass. (See figure 1)

Soak two filters in cold tap water for 15 minutes.

2. WASH

1

12

2

Cold and hot water will be ready to serve when the heating and cooling lights above the water dispensing push buttons shut off.

For the Filter Life Indicator to function, fill water to the fill line on top of the fill tank each time it is refilled and allow the water to drain completely out of the filter tray before refilling the fill tank.

Hand-wash all components (except filters): Reservoir, filter tray, float valve, fill tank and fill tank cap with mild soapy water while filter is soaking. (See figure 2) Rinse each component with water. Note: Do not place components in dishwasher, they are not dishwasher safe.

Insert reservoir and filter tray into product. Do not install filters. (See figure 3)

3.FLUSH SYSTEM WITHOUT FILTERS (1st Use Only)

• USE COLD WATER ONLY.

Open fill cap and fill the fill tank to the fill line with cold water. (See figure 4) Close fill cap firmly. If fill tank is damaged or cracked, discontinue use and contact our Consumer Relations Department for replacement.

Turn fill tank upside down and place on filter tray. (See figure 5)

Remove water from unit by placing a 3-gallon bucket under the drain plug. Unscrew drain plug to release water into the bucket. Caution-water could be hot. Replace drain plug.

Dispense remaining water by pressing cold temperature button (marked with blue waves), room temperature button (gray waves) and hot temperature water (marked with red waves) into a large glass.

Flush system twice, then move on to step 4.

4. FLUSH FILTERS

Hold filters upright under cold running tap water for 10 seconds to flush. (See figure 6)

5. DRAIN FILTERS

• Allow excess water to drain from filters. (See figure 7)

6. REMOVE SHIPPING RETAINER

Remove shipping retainer from top of each filter by pulling retainer straight up and out. (See figure 8)

3

4

5

6

7

8

9A

9B

Image 5
Contents Manuel d’utilisation et d’entretien Use and Care ManualManual para uso y mantenimiento Page Safety Precautions Table of ContentsUnpack and Remove ALL Packaging Materials Unpacking and PartsSetting Up Your Water Cooler Key Features How to Monitor Filter LifeFrequently Asked Questions Proper Care and CleaningTroubleshooting Storing UnitPurchases Made In Iowa Limited Product WarrantyTechnical Specifications Contaminant Removal Data Important Notice Performance Data SheetImportante Precauciones de seguridad ÍndiceLEA Todas Estas Instrucciones Antes DE Usar Guarde Estas Instrucciones para consultar en el futuroDesempaque Y Remueva Todos LOS Materiales DE Embalaje Desempaque y componentesSistema de filtración Las características más importantes Descontinuar la operación Resolución de problemasCuidado y mantenimiento Especificaciones técnicas Garantía limitada del productoCompras hechas en Iowa Refrescador de agua PU¯ R Modelo PU¯ R220/CRF-950 Hoja de datos de rendimientoPage Mesures de sécurité Table des matièresLire Toutes LES Instructions Avant D’UTILISER LE Produit Conserver CES Instructions pour consultation ultérieureDéballer ET Enlever Tous LES Matériaux D’EMBALLAGE Déballage et piècesSystème de filtration Caractéristiques principales Remisage de l’appareil Entretien et nettoyage appropriésFoire Aux Questions DépannageSpécifications techniques Garantie limitée sur le produitAchats faits en Iowa Élimination Fiche de données de performancePage Page 035-04026-000, Rev A/W