Kenmore 362.72220 manual Provide Adequate Gas Supply, Connect the Range to Gas, Preparation, Step

Page 32

PREPARATION

•Remove all tape and packaging_ Lift up the cooktop (on models with standard twin burners) and remove any packing material under it. Make sure the standard twin burners are properly seated and level.

•Remove plastic film that covers some chrome parts (around oven door, side trim).

•Take the accessory pack out of the oven.

o Check to be sure that no range parts have come loose during shipping.

STEP 1

Provide Adequate Gas Supply

Your range is designed to operate at a pressure of 4" (10.2 cm) of water column on natural gas or, if designed for LP gas (propane or butane), 10" (25.4 cm) of water column.. Make sure you are supplying your range with the type of gas for which it is designed.

This range is convertible for use on natural or propane gas.. If you decide to use this range on LP gas, conversion must be made by a qualified LP installer before attempting to operate the range on that gas°

For proper operation, the pressure of natural gas supplied to the regulator must be between 4" (10o2 cm) and 13" (33 cm) of water column. For LP gas, the pressure supplied must be between 10" (25.4 cm) and !3" (33 cm) of water column.. When checking for proper operation of the regulator, the inlet pressure must be at least 1" (2.5 cm) greater than the operating (manifold) pressure as given above. The pressure regulator located at the inlet of the range manifold must remain in the supply line regardless of whether natural or LP gas is being used° A flexible metal appliance connector used to connect the range to the gas supply line should have an I.D of 1/2" and be 5 feet (1..5 m) in length for ease of installation_ In Canada, flexible connectors must be single wall metal connectors no longer than 6 feet

(1.8 m)in length.

STEP 2

Connect the Range to Gas

Shut off the main gas supply valve before disconnecting the old range and leave it off until new hook-up has been completed., Don'tforget to relight the pilot on other gas appliances when you turn the gas back on,,

Because hard piping restricts movement of the range, the use of an A..G_A.-certified flexible metal appliance connector is recommended unless local codes require a hard-piped connection. Never use an old connector when installing a new range.. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.

To prevent gas leaks, use pipe joint compound or wrap Teflon* pipe thread tape around all male (external) pipe threads.

*Teflon: Registered trademark of DuPont

Gas Pipe and Electric Outlet Locations for

Models Equipped with Sealed Burners

This area aitows

for flush range installation with

through-the-wall connection of pipe stub/shut-off valve and rear wall 120V OUflet.r

Shortest connection from

hard pipe stub location to

range hookup.

I connection of pipe

Istub/shut-off valve, r

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents GAS Range Cocina Estufa DE GAS Maintenance InstructionsOperation En EspafiolImportant Safety Notice California Safe Drinking Water and ToxicUsing Your Range To the vent Cleaning YourRange Con To Light a Surface Burner Lighting Instructions For Standing Pilot ModelsLighting Instructions for Electronic Ignition Models How to Select Flame Size After Lighting a BurnerTop-of-Range Cookware Wok This WayTo Set the Timer To Change or Cancel the Timer SettingTo Display the Clock While Timer Is Operating On some modelsBefore Using Your Oven Power OutageStanding Pilot Models Lighting Instructions for Electric Ignition ModelsOven Shelves Oven Temp KnobOven Light On some models Shelf Positions Oven VentsHow to Set Your Range for Baking BakingOven Shelves Cookies Or cupcakesNever entirely cover a shelf with aluminum foil Dont Peek Set the timer for the estimated cooking timeAluminum Foil Adjust the Oven Thermostat Do It Yourself Air Adjustment Shutter for Oven BurnersType of Margarine Will Affect Baking Performance You may feel that your new oven cooks differentlyRoasting Dual Shelf CookingUse Aluminum FoilRoasting Guide Use of Aluminum Foil How to BroilBroiling Broiling Guide Oven door and broiler drawer must be closed during BroilingBe Sure Electrical Power is Disconnected Sealed Burner AssembliesIgniter Burner HeadsBurner Grates Drip PansClean Standard Twin BurnersIon some models Lift-Up CooktopOven Air Vents Broiler Pan and GridLower Control Panel Front Manifold Panel and Knobs Oven Light Bulb on some modelsTo Clean the Door Lift-Off Oven DoorInside of door Outside of doorOven Bottom Removable Broiler DrawerOven bottom has a porcelain enamel finish+ To removeSpecial Care of the Continuous Cleaning Oven Interior Oven bottom has a porcelain enamel finishFor Your Safety Dimensions and Clearances Height76,2 cm 5cmTo wall on eitherInstructions General Additional Materials YOU MAY NeedProvide Adequate Gas Supply Connect the Range to GasPreparation StepBurners For Models EquippedWith Standard Power Cord TFIPreferred MethodYou will have this disconnect plug Seal the OpeningsElectric Disconnect Adjust the Surface Burner Pilots If Necessary Light the Oven PilotCheck Ignition of Oven Burner Adjusting the Air Adjustment Shutter if Necessary Leveling the RangeInstalling the Anti-Tip Device Converting to LP gasAjoneelcabinetor SidePaneliStandard Twin Burner Models Sealed Burner ModelsPossible Cause Full ONE-YEAR Warranty on ALL Parts Master Protection Agreements

362.71332, 362.61021, 362.61020, 362.61121, 362.72224 specifications

The Kenmore 362 series, which includes models 362.72232, 362.72221, 362.72220, 362.72222, and 362.71330, is a notable range of appliances known for their reliability, performance, and innovative features. These models are designed to cater to diverse cooking needs while ensuring energy efficiency and user convenience.

One of the main features of the Kenmore 362 series is its versatility in cooking options. These appliances typically come equipped with various cooking modes, including baking, broiling, and roasting, allowing users to prepare a wide range of recipes. Additionally, some models in the series incorporate a convection feature, which circulates hot air for even cooking and browning, making it perfect for baking pastries and roasting meats.

User-friendly digital controls are another characteristic of the Kenmore 362 line. These intuitive interfaces allow for precise temperature settings and cooking times, making it easier than ever to achieve perfect results. Many models may also include pre-programmed cooking settings, enabling users to select options based on specific meals, which simplifies the cooking process.

In terms of characteristics, the Kenmore 362 series is designed with quality materials that provide durability and longevity. The interiors are often coated with non-stick surfaces, making cleaning a breeze. The external designs typically feature sleek finishes that can complement any kitchen decor while ensuring easy operation through strategically placed knobs and buttons.

Energy efficiency is a significant consideration in the Kenmore 362 models. These units are generally ENERGY STAR rated, which denotes lower energy consumption without compromising performance. This focus on sustainability helps reduce utility bills while serving the dual purpose of being an environmentally friendly choice.

Safety features are also paramount in the Kenmore 362 series. Many models are fitted with automatic shut-off functions, ensuring that the appliances turn off after a set period of inactivity. Moreover, cool-to-the-touch exteriors help prevent accidental burns, making these ovens suitable for families with children.

Overall, the Kenmore 362 series, including the models 362.72232, 362.72221, 362.72220, 362.72222, and 362.71330, combines modern technology with practical design, providing users with efficient, reliable, and versatile cooking solutions for any kitchen.
Top Page Image Contents