Murray 425015x92A IMPORTANT! Before YOU Start Mowing, HOW to Prepare the Engine, Check the Tires

Page 13

ASSEMBLY

IMPORTANT! BEFORE YOU START MOWING

-Check the engine oil.

-Fill the fuel tank with gasoline.

-Check the level of the mower housing.

-Check the air pressure of the tires.

-Make sure the battery cables are attached.

WARNING: Before doing any assembly or mainte- nance to the mower, remove the wire from the spark plug.

NOTE: In this instruction book, left and right describe the loca- tion of a part with the operator on the seat.

HOW TO PREPARE THE ENGINE

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type of gasoline and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage.

WARNING: Follow the engine manufacturer’s instructions for the type of gasoline and oil to use. Always use a safety gasoline container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gasoline. Before you add gasoline, stop the engine. Let the engine cool for several minutes.

IMPORTANT: This unit is equipped with an internal combustion engine and must not be used on or near any unimproved

forest–covered, brush–covered or grass–covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it must be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. See an Authorized Service Center for a spark arrester for the muffler.

In some areas, local law requires the use of a resistor spark plug to control the ignition signals. See an Authorized Service Center for a resistor spark plug for the engine.

NOTE: Actual sustained horsepower will likely be lower due to operating limitations and environmental factors.

CHECK THE LEVEL OF THE MOWER HOUSING

Make sure the level of cut is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section of this instruction book.

CHECK THE TIRES

Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure (PSI) is 14 PSI (1 BAR). The tires were over inflated for shipment.

F–040734L

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables Check the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresLocation of Controls OperationLift Lever HOW to USE the Shift Lever HOW to USE THROTTLE/CHOKE ControlAttachments See the Instruction Book for the AttachmentHOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingBefore Starting the Engine HOW to Start the EngineCarburetor Mowing and Bagging Tips Operating TipsFrequency Maintenance Required Comments MaintenanceHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchDisconnect the adjuster nut from the shifter bracket Figure HOW to Adjust the Shift LeverHOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Removal HOW to Replace Motion Drive BeltInstallation HOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart USA 040734LChassis & Hood Repair PartsKey Description Motion Drive Motion Drive Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Light Harness Electrical SystemElectrical System 040734L Index Model No Bushel Capacity Model No

425015x92A specifications

Murray 425015x92A is a state-of-the-art piece of equipment showcasing advanced engineering and innovative technologies designed for optimal performance in various applications. This model is distinguished by its robust build and versatile functionality, making it an ideal choice for both industrial and commercial sectors.

One of the key features of the Murray 425015x92A is its high-efficiency motor. The motor is designed to minimize energy consumption while maximizing output, which not only lowers operational costs but also contributes to sustainability efforts. Coupled with an advanced cooling system, the motor maintains optimal operating temperatures, ensuring reliability and longevity.

The device is equipped with smart technology that enhances its performance. This includes an intuitive control panel that allows users to easily monitor and adjust settings according to their needs. With digital displays and user-friendly interfaces, operators can quickly access real-time data and make informed decisions on performance optimization.

In terms of safety features, the Murray 425015x92A integrates several protective mechanisms. These include overload protection, emergency shut-off switches, and safety interlocks that prevent accidental operation. Such features ensure that both the equipment and its operators remain safe during use.

Durability is another characteristic that sets the Murray 425015x92A apart from its competitors. Constructed with high-grade materials and components, it is designed to withstand harsh working environments. It can resist dust, moisture, and other environmental factors, making it suitable for use in various conditions, from manufacturing floors to outdoor job sites.

The versatility of the Murray 425015x92A is also noteworthy. It can be configured for multiple applications, from heavy-duty industrial tasks to lighter commercial projects. Its adaptable design allows for quick modifications, increasing its utility across different fields.

Additionally, the equipment is backed by a comprehensive support system. Murray provides extensive customer service, including installation assistance, technical support, and maintenance options. This commitment to customer satisfaction ensures that users can rely on their equipment for sustained performance.

In conclusion, the Murray 425015x92A is an exemplary model reflecting a blend of efficiency, safety, and versatility. With its advanced technologies and robust construction, it stands as a valuable asset for diverse applications across various industries, making it a preferred choice for professionals seeking reliability and performance.
Top Page Image Contents