Murray 425015x92A manual Trouble Shooting Chart

Page 34

TROUBLE SHOOTING CHART

PROBLEM: The engine will not start.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric–Start Models: Clean the battery terminals. Tighten the cables.

3.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

4.Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position. Try to start the en- gine several times. Install the spark plug.

5.Replace the spark plug.

6.Adjust the carburetor.

PROBLEM: The engine will not turn over.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric–Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery.

3.Replace the fuse.

4.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

5.Electric–Start Models: replace the solenoid. Recoil–Start Mod-

els: replace the module.

PROBLEM: The engine is difficult to start.

1.Adjust the carburetor.

2.Replace the spark plug.

3.Replace the fuel filter.

PROBLEM: The engine does not run smooth or has a loss of power.

1.Check the oil.

2.Clean the air filter.

3.Clean the air screen.

4.Replace the spark plug.

5.The engine is working too hard. Use a lower gear.

6.Adjust the carburetor.

7.Replace the fuel filter.

PROBLEM: The engine does not run smooth at fast speed.

1.Replace the spark plug.

2.Adjust the throttle control.

3.Clean the air filter.

4.Replace the fuel filter.

PROBLEM: The engine stops when the blades are engaged.

1.To activate the seat sensor, always sit in the middle of the seat.

2.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

PROBLEM: On slopes, the engine stops.

1.Mow up and down slopes. Never mow across a slope.

2.To activate the seat sensor, always sit in the middle of the seat.

PROBLEM: The engine will not idle.

1.Replace the spark plug.

2.Clean the air filter.

3.Adjust the carburetor.

4.Adjust the throttle control.

5.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

PROBLEM: A hot engine causes a decrease in power.

1.Clean the air screen.

2.Check the oil.

3.Adjust the carburetor.

4.Replace the fuel filter.

PROBLEM: Excessive vibration.

1.Replace the blade.

2.Check for loose engine bolts.

3.Decrease the air pressure in the tires.

4.Adjust the carburetor.

5.Check for a damaged belt or damaged pulley. Replace the damaged parts.

PROBLEM: The grass does not discharge correctly.

1.Stop the engine. Clean the mower housing.

2.Raise the height of cut.

3.Replace or sharpen the blade(s).

4.Move the shift lever to a slower speed.

5.Move the throttle control to the FAST position.

6.Replace the spring for the blade idler.

PROBLEM: The mower housing does not cut level.

1.Check the air pressure in the tires.

2.Adjust the level of the mower housing.

3.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The mower blades will not rotate.

1.Check the mower drive belt. Make sure the belt is installed cor- rectly.

2.Replace the mower drive belt.

PROBLEM: The unit will not move when the clutch is engaged.

1.Check the motion drive belt. Make sure the belt is installed correctly.

2.Adjust the clutch.

3.Replace the motion drive belt.

PROBLEM: The unit moves slower or stops when the clutch is engaged.

1.Adjust the clutch.

2.Replace the motion drive belt.

PROBLEM: When the clutch/brake pedal is released, belt noise can be heard.

1.Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides.

2.If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over uneven terrain.

1.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The transaxle is difficult to shift between gears with the engine running and the clutch depressed.

1.Check the clutch adjustment to make sure the belt stops when the clutch pedal is depressed with the transaxle in (N) neutral.

2.Check the belt guides around the transaxle drive pulley. Make sure the belt guides do not touch the pulley.

F–040734L

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model Table of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresLocation of Controls OperationLift Lever Attachments HOW to USE THROTTLE/CHOKE ControlHOW to USE the Shift Lever See the Instruction Book for the AttachmentHOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceFrequency Maintenance Required Comments General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Adjust the Shift Lever Disconnect the adjuster nut from the shifter bracket FigureWhere to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing HOW to Replace Motion Drive Belt RemovalInstallation HOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart 040734L USARepair Parts Chassis & HoodKey Description Motion Drive Motion Drive Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Electrical System Light HarnessElectrical System 040734L Index Model No Model No Bushel Capacity

425015x92A specifications

Murray 425015x92A is a state-of-the-art piece of equipment showcasing advanced engineering and innovative technologies designed for optimal performance in various applications. This model is distinguished by its robust build and versatile functionality, making it an ideal choice for both industrial and commercial sectors.

One of the key features of the Murray 425015x92A is its high-efficiency motor. The motor is designed to minimize energy consumption while maximizing output, which not only lowers operational costs but also contributes to sustainability efforts. Coupled with an advanced cooling system, the motor maintains optimal operating temperatures, ensuring reliability and longevity.

The device is equipped with smart technology that enhances its performance. This includes an intuitive control panel that allows users to easily monitor and adjust settings according to their needs. With digital displays and user-friendly interfaces, operators can quickly access real-time data and make informed decisions on performance optimization.

In terms of safety features, the Murray 425015x92A integrates several protective mechanisms. These include overload protection, emergency shut-off switches, and safety interlocks that prevent accidental operation. Such features ensure that both the equipment and its operators remain safe during use.

Durability is another characteristic that sets the Murray 425015x92A apart from its competitors. Constructed with high-grade materials and components, it is designed to withstand harsh working environments. It can resist dust, moisture, and other environmental factors, making it suitable for use in various conditions, from manufacturing floors to outdoor job sites.

The versatility of the Murray 425015x92A is also noteworthy. It can be configured for multiple applications, from heavy-duty industrial tasks to lighter commercial projects. Its adaptable design allows for quick modifications, increasing its utility across different fields.

Additionally, the equipment is backed by a comprehensive support system. Murray provides extensive customer service, including installation assistance, technical support, and maintenance options. This commitment to customer satisfaction ensures that users can rely on their equipment for sustained performance.

In conclusion, the Murray 425015x92A is an exemplary model reflecting a blend of efficiency, safety, and versatility. With its advanced technologies and robust construction, it stands as a valuable asset for diverse applications across various industries, making it a preferred choice for professionals seeking reliability and performance.
Top Page Image Contents