Murray 425015x92A Attachments, HOW to USE THROTTLE/CHOKE Control, HOW to USE the Shift Lever

Page 15

OPERATION

ATTACHMENTS

This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader, or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator.

For all pull–behind attachments or trailers, the maximum gross weight is 250 pounds. Gross weight is the weight of the attachment or trailer and any load that might be on or in it.

Do not operate on a slope that is greater than 10 degrees when using a pull–behind attachment or trailer. We have included a slope guide in this book to help you determine the slope on which you will be operating your unit. Never allow someone to stand or ride on or in an attachment or trailer.

HOW TO USE

THE THROTTLE/CHOKE CONTROL

Use the throttle/choke control to choke the engine for cold starts and increase or decrease the speed of the engine.

1.Move the throttle/choke control completely forward to the CHOKE position to start a cold engine.

2.The FAST position is marked with a detent. For normal opera- tion and when using a grass bagger, move the throttle control to the FAST position. For maximum charging of the battery and for a cooler running engine, operate the engine in the FAST position.

3.The engine governor is set at the factory for maximum perfor- mance. Do not adjust the governor to increase the speed of the engine.

HOW TO USE THE BLADE ROTATION CONTROL

Use the blade rotation control to engage the blade(s) (Figure 6).

Disengage

Position

Blade Rotation Control

Engage Position

Figure 6

1.Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position.

2.Move the blade rotation control to the ENGAGE position to rotate the blade(s).

NOTE: If the engine stops when you engage the blade(s), the seat switch is not activated. Make sure you sit in the middle of the seat.

3.Move the blade rotation control to the DISENGAGE position to stop the blade(s). Before you leave the operator’s position, make sure the blade(s) has stopped rotating.

4.Before you ride the unit across a sidewalk or a road, move the blade rotation control to the DISENGAGE position.

WARNING: Always keep your hands and feet away from the blade, deflector opening, and the mower housing when the engine runs.

HOW TO USE THE SHIFT LEVER

To change the forward speed or the direction of the unit, follow the steps below.

CAUTION: Before you move the shift lever, completely push the clutch/brake pedal forward to stop the unit. If the unit is not stopped, the gearbox can be damaged.

1.Completely push the clutch/brake pedal forward to stop the unit. Keep your foot on the pedal.

2.Move the throttle control lever to the SLOW position.

3.To go forward, move the shift lever to a forward speed setting. To go backward, move the shift lever to reverse.

4.Slowly release the clutch/brake pedal. Do not keep your foot on the pedal.

5.Move the throttle control to the FAST position.

FUNCTION

SHIFT LEVER

THROTTLE

 

6 Speeds

 

 

 

 

Trimming

1

 

Snow Thrower

 

 

 

 

 

Bagging Grass

1 or 2

 

 

 

FAST

Mulching Grass

1 or 2

CHOKE

 

 

 

Normal Mowing

2 or 3

FAST

 

 

 

Easy Mowing

3 or 4

 

Snow Blade

 

SLOW

 

 

THROTTLE

Transport

5 or 6

 

 

 

 

Attachments

*

 

 

 

 

* See the Instruction Book for the Attachment.

F–040734L

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Check the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingOperation Location of ControlsLift Lever See the Instruction Book for the Attachment HOW to USE THROTTLE/CHOKE ControlHOW to USE the Shift Lever AttachmentsHOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchDisconnect the adjuster nut from the shifter bracket Figure HOW to Adjust the Shift LeverHOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing Removal HOW to Replace Motion Drive BeltInstallation HOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart USA 040734LChassis & Hood Repair PartsKey Description Motion Drive Motion Drive Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Light Harness Electrical SystemElectrical System 040734L Index Model No Bushel Capacity Model No

425015x92A specifications

Murray 425015x92A is a state-of-the-art piece of equipment showcasing advanced engineering and innovative technologies designed for optimal performance in various applications. This model is distinguished by its robust build and versatile functionality, making it an ideal choice for both industrial and commercial sectors.

One of the key features of the Murray 425015x92A is its high-efficiency motor. The motor is designed to minimize energy consumption while maximizing output, which not only lowers operational costs but also contributes to sustainability efforts. Coupled with an advanced cooling system, the motor maintains optimal operating temperatures, ensuring reliability and longevity.

The device is equipped with smart technology that enhances its performance. This includes an intuitive control panel that allows users to easily monitor and adjust settings according to their needs. With digital displays and user-friendly interfaces, operators can quickly access real-time data and make informed decisions on performance optimization.

In terms of safety features, the Murray 425015x92A integrates several protective mechanisms. These include overload protection, emergency shut-off switches, and safety interlocks that prevent accidental operation. Such features ensure that both the equipment and its operators remain safe during use.

Durability is another characteristic that sets the Murray 425015x92A apart from its competitors. Constructed with high-grade materials and components, it is designed to withstand harsh working environments. It can resist dust, moisture, and other environmental factors, making it suitable for use in various conditions, from manufacturing floors to outdoor job sites.

The versatility of the Murray 425015x92A is also noteworthy. It can be configured for multiple applications, from heavy-duty industrial tasks to lighter commercial projects. Its adaptable design allows for quick modifications, increasing its utility across different fields.

Additionally, the equipment is backed by a comprehensive support system. Murray provides extensive customer service, including installation assistance, technical support, and maintenance options. This commitment to customer satisfaction ensures that users can rely on their equipment for sustained performance.

In conclusion, the Murray 425015x92A is an exemplary model reflecting a blend of efficiency, safety, and versatility. With its advanced technologies and robust construction, it stands as a valuable asset for diverse applications across various industries, making it a preferred choice for professionals seeking reliability and performance.
Top Page Image Contents