Murray 425015x92A manual II. Slope operation

Page 4

OWNER’S INFORMATION

b.Limit loads to those you can safely control.

c.Do not turn sharply. Use care when backing.

d.Use counterweights or wheel weights when suggested in the Instruction Book.

19.Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine.

20.Do not use this machine if you are mentally or physically unable to operate this machine safely.

21.Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower related injuries. These opera- tors should evaluate their ability to operate a riding mower safely enough to protect themselves and others from serious injury.

II. Slope operation

Slopes and rough terrain are major factors related to loss–of–control and tip–over accidents, which can result in severe injury or death. ALL slopes require extra caution. If you cannot back up the slope or if you feel uneasy on the slope, do not mow it. See the “Slope Guide” in the back of this book to check for safe operation.

DO

1.Mow up and down slopes, not across.

2.Remove obstacles such as rocks, limbs, etc...

3.Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

4.Use slow speed. Choose a low enough gear so that you will not have to stop or shift while on the slope.

5.Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.

6.Use extra care with grass baggers or other attachments, they can change the stability of the machine.

7.Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.

8.Avoid starting or stopping on a slope. If tires lose traction, turn off the blades and proceed slowly straight down the slope.

DO NOT

1.Do not turn on slopes unless absolutely necessary, then only turn slowly and gradually downhill, if possible.

2.Do not mow drop–offs, ditches or embankments. A wheel over the edge or an edge caving in could cause a sudden overturn and an injury or death.

3.Do not mow on wet grass. Reduced traction could cause sliding.

4.Do not try to stabilize the machine by putting your foot on the ground.

5.Do not use a grass bagger or other rear mounted accessories on steep slopes (greater than 10 degrees).

III. Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. NEVER assume that children will remain where you last saw them.

1.Keep children out of the mowing area and in the watchful care of another responsible adult.

2.Be alert and turn the engine off if children enter the area.

3.Before and when backing, look behind and down for small children.

4.Never carry children or any passengers, even with the blades off. They may fall off and be seriously injured or interfere with the safe operation of the machine.

5.Never allow children to operate the machine. Instruct children in the potential dangers of the machine.

6.Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure vision.

IV. Service

1.Use extra care when handling gasoline and other fuels. Fuels are flammable and the vapors are explosive.

a.Use only an approved container.

b.Never remove the gas cap or add fuel with the engine running. Allow the engine to cool for several minutes before refueling. Do not smoke.

c.Never refuel the machine indoors.

d.Never store the machine with fuel in the tank or fuel container inside where there is an open flame, such as a water heater.

2.Never start or run the engine inside a closed area.

3.Keep all nuts and bolts, especially the blade attachment nuts tight. Frequently check the blade(s) for wear or damage such as cracks and nicks. A blade that is bent or damaged must be immediately replaced with an original equipment blade from an authorized service dealer. For safety, replace the blade every two years. Keep the equipment in good condition.

4.Never tamper with the safety devices. Check their proper operation regularly.

5.To reduce fire hazards, keep the machine free of grass, leaves or other debris build–up. Clean up oil or fuel spills. Allow the machine to cool before storing.

6.Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

7.Never make adjustments or repairs with the engine running. The carburetor can be adjusted with the engine running. Do not change the engine governor settings or over–speed the engine.

8.Grass bagger components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. For storage, always make sure the grass bag is empty. Frequently check components and replace with manufacturer’s recom- mended parts when necessary.

9.Mower blade(s) are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them or the blade housing area.

10.Check the brake operation frequently. Adjust and service as required.

11.Wait for all movement to stop before servicing any part of the unit.

Look for this symbol to indicate important safety precautions. This symbol indicates: “Attention! Become Alert! Your Safety Is At Risk.”

F–040734L

4

Image 4
Contents Model Table of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables HOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresLocation of Controls OperationLift Lever HOW to USE THROTTLE/CHOKE Control HOW to USE the Shift LeverAttachments See the Instruction Book for the AttachmentHOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineCarburetor Operating Tips Mowing and Bagging TipsMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Adjust the Shift Lever Disconnect the adjuster nut from the shifter bracket FigureWhere to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing HOW to Replace Motion Drive Belt RemovalInstallation HOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart 040734L USARepair Parts Chassis & HoodKey Description Motion Drive Motion Drive Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Electrical System Light HarnessElectrical System 040734L Index Model No Model No Bushel Capacity

425015x92A specifications

Murray 425015x92A is a state-of-the-art piece of equipment showcasing advanced engineering and innovative technologies designed for optimal performance in various applications. This model is distinguished by its robust build and versatile functionality, making it an ideal choice for both industrial and commercial sectors.

One of the key features of the Murray 425015x92A is its high-efficiency motor. The motor is designed to minimize energy consumption while maximizing output, which not only lowers operational costs but also contributes to sustainability efforts. Coupled with an advanced cooling system, the motor maintains optimal operating temperatures, ensuring reliability and longevity.

The device is equipped with smart technology that enhances its performance. This includes an intuitive control panel that allows users to easily monitor and adjust settings according to their needs. With digital displays and user-friendly interfaces, operators can quickly access real-time data and make informed decisions on performance optimization.

In terms of safety features, the Murray 425015x92A integrates several protective mechanisms. These include overload protection, emergency shut-off switches, and safety interlocks that prevent accidental operation. Such features ensure that both the equipment and its operators remain safe during use.

Durability is another characteristic that sets the Murray 425015x92A apart from its competitors. Constructed with high-grade materials and components, it is designed to withstand harsh working environments. It can resist dust, moisture, and other environmental factors, making it suitable for use in various conditions, from manufacturing floors to outdoor job sites.

The versatility of the Murray 425015x92A is also noteworthy. It can be configured for multiple applications, from heavy-duty industrial tasks to lighter commercial projects. Its adaptable design allows for quick modifications, increasing its utility across different fields.

Additionally, the equipment is backed by a comprehensive support system. Murray provides extensive customer service, including installation assistance, technical support, and maintenance options. This commitment to customer satisfaction ensures that users can rely on their equipment for sustained performance.

In conclusion, the Murray 425015x92A is an exemplary model reflecting a blend of efficiency, safety, and versatility. With its advanced technologies and robust construction, it stands as a valuable asset for diverse applications across various industries, making it a preferred choice for professionals seeking reliability and performance.