Toro manual Adjusting Traction Control, Adjusting the Traction Control Toro Models 38065, 38080

Page 29

Belts, Controls and Linkages

ADJUSTING TRACTION CONTROL

Adjusting the Traction Control — Toro Models 38065, 38080, 38085

1.Move wheel drive control into No. 1, 1st gear. Position control lever so its front surface is 1/4 of an inch (6mm) from bottom of slot (Figure 56); then hold lever in this position.

(6 mm)

Figure 56

13299-5

2.While holding wheel drive control lever in position, push up on long rod and rotate clevis until holes in clevis line up with hole in link arm (Figure 57).

Next, secure clevis and link arm together with clevis pin and cotter pin (Figure 57).

1

5

42

3

 

 

 

 

 

 

 

Figure 57

13299-6

1.

Long rod

6.

Clevis

2.

Clevis

7.

Short rod

3.

Link arm

8.

Clevis pin and

4.

Clevis pin and

cotter pin

 

cotter pin

9.

Jam nut

5.Shift arm

3.Move wheel drive control lever onto the hump between N and 1 (Figure 58). Hold wheel drive control lever in this position — on hump.

Note: Lever must be held against the hump, not in the N or 1 position.

 

 

 

Figure 58

13299-7

4.Move shift arm fully to the left (Figure 57). Next, rotate clevis at end of short rod until holes in clevis line up with hole in shift arm (Figure 57). Secure clevis and shift arm together with clevis pin and cotter pin (Figure 57).

5.Tighten the jam nut against top of both clevises (Figure 57).

Two Stage Snowthrower Drive Systems Manual

2 - 9

Image 29
Contents TORO/LAWN-BOY TWO Stage Snowthrower Drive Systems Manual Table of Contents Page 2 Stage Snowthrower Drive Systems About This Manual Contents This page Intentionally Left Blank Introduction Introduction Gearbox Removal General InformationAuger Gearbox Lubricant Primary Method Minimum Disassembly Loosen Remove Disconnect the chute crank rod at the auger Figure Now perform steps 1 9 under Gearbox Removal on page 1 Installation Auger Gearbox Disassembly / Service 1577-028 Failure Analysis Gearbox AssemblyLetter R and arrow 2773-059 This page Intentionally Left Blank Replacing the AUGER/IMPELLER Drive Belt IntroductionReplacing the Traction Belt Toro Models 38065, 38080 Replacing the Traction BeltBelt cover Upper belt cover Screw View from left side of unit Tabs in holes Auger Control Adjustment Toro Models 38065, 38080 Control and Linkage AdjustmentAuger/Impeller Drive Control Linkage All Other Models Adjusting the Traction Control Toro Models 38065, 38080 Adjusting Traction ControlCm . This is a preliminary setting only Traction control lever 8 in cm Handgrip .5-5 cm Adjusting the Speed Selector Traction Drive Systems Disassembly Toro Models 38065, 38080 Troubleshooting the Traction Drive ALL ModelsTo disassemble the pivot assembly, proceed as follows Figure Assembly Toro Models 38065, 38080 Preparation Assembly 2768-033 MVC-714 Gear quadrant Self-tapping screws Assembly Steps 2773-078 If the receiver cam has been removed, install it now MVC-716 Disassembly Toro Models 38066, 38078, 38083, 38084 Traction engagement rod Assembly Toro Models 38066, 38078, 38083, 38084 Toro Models 38066, 38078, 38083, 38084 SUB Assembly RepairTraction Shaft/Friction Wheel Disassembly Axle and Friction Plate Disassembly Axle and Friction Plate Assembly This page Intentionally Left Blank Page 492-4738