Toro 20200, 20199 owner manual Washing Underneath the Machine

Page 24

WARNING

Incorrectly installing the blades could damage the machine or cause an injury to the operator or to bystanders.

Washing Underneath the Machine

Service Interval: Before each use or daily—Wash underneath the machine.

1.Move the machine to a level surface.

2.Stop the engine and wait for all moving parts to stop before leaving the operating position.

3.Lower the machine to the lowest height-of-cut.

4.Attach a hose to the washout fitting, and turn the water on high (Figure 48).

Note: Spread petroleum jelly on the washout fitting O-ring to make the coupling slide on easier and protect the O-ring.

 

 

Figure 48

 

1.

Washout fitting

3.

O-ring

2.

Hose

4.

Coupling

5.Start the engine, engage the blade-control lever, and let the machine run for 1 to 3 minutes.

6.Disengage the blade-control lever, stop the engine, and wait for all moving parts to stop.

7.Shut off the water and remove the coupling from the washout fitting.

Note: If the machine is not clean after a single washing, soak it and let it stand for 30 minutes. Then repeat the process.

8.Run the machine again and engage the blades for 1 to 3 minutes to remove the excess water.

WARNING

A broken or missing washout fitting could expose you and others to thrown objects or blade contact. Contact with a blade or thrown debris can cause injury or death.

•Replace a broken or missing washout fitting immediately, before using the machine again.

•Never put your hands or feet under the machine or through openings in the mower.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Introduction TimeMaster 30in Lawn MowerSafety General OperationSlope Operation Service General ServiceChildren Safe Handling of GasolineSafety and Instructional Decals 114-7982Setup No Parts Required ProcedureAssembling the Handle Installing the Blade-control Bar Parts needed for this procedureFilling the Engine with Oil Charging the Battery Product OverviewUsing Fuel Stabilizer/Conditioner OperationBefore Starting Recommended Fuel Filling the Fuel TankAdjusting the Cutting Height Checking the Engine Oil LevelAdjusting the Handle Height Starting the EngineStandard Model Electric-start ModelUsing the Self-propel Drive Stopping the EngineEngaging the Blade Using the Grass Bag Not Using the Grass BagDisengaging the Blade Checking the Blade-stop System OperationInstalling the Grass Bag Recycling the ClippingsBagging the Clippings Installing the Side-discharge Chute Side-discharging the ClippingsRemoving the Grass Bag Removing the Side-discharge ChuteOperating Tips General Mowing TipsCutting Grass Cutting LeavesMaintenance Recommended Maintenance SchedulesPreparing for Maintenance Servicing the Air Filter Changing the Engine OilService Interval Every 25 hours Replacing the Battery Removing the Old BatteryInstalling the New Battery Replacing the FuseAdjusting the Self-propel Drive Cable Servicing the Blade-drive SystemPreparing to Service the Cutting Blades Servicing the Cutting BladesInspecting the Blades Checking for Bent Blades Removing the BladesInstalling the Blades Washing Underneath the Machine Storage General InformationPreparing the Fuel System Preparing the EnginePage Page Toro Total Coverage Guarantee

20199, 20200 specifications

The Toro 20200 and 20199 are two versatile and innovative products designed to enhance landscaping and maintenance tasks for both professionals and homeowners. These models offer a range of features and technologies that cater to various needs, making them a top choice for turf care.

One of the primary features of the Toro 20200 is its efficient 21-inch cutting deck. This deck size provides the perfect balance between maneuverability and cutting efficiency, allowing users to tackle both small and medium-sized yards with ease. The 20199 model boasts similar dimensions, ensuring it can fit into tight spaces while still covering considerable ground.

Both models are equipped with Toro's proprietary Recycler cutting system. This technology allows for superior mulching capabilities, ensuring grass clippings are finely shredded and distributed back onto the lawn. This process not only enhances the appearance of the lawn but also contributes to its health by returning essential nutrients to the soil.

The power behind the Toro 20200 and 20199 comes from their robust engines. Both models utilize efficient gas engines that deliver ample power for cutting through tough grass, while also being designed for fuel efficiency. This ensures longer run times between refueling, saving both time and energy for users.

Ease of use is a hallmark of the Toro brand, and these models exemplify that. The self-propelled drive system on both the 20200 and 20199 models simplifies operation by allowing users to set their walking pace, making mowing less strenuous. Additionally, the adjustable cutting heights provide versatility for various grass types, ensuring optimal results throughout the growing season.

Durability is another key characteristic, with both models featuring sturdy construction to withstand the rigors of regular use. This durability is complemented by Toro's commitment to customer support, ensuring that users can rely on their equipment for years to come.

In summary, the Toro 20200 and 20199 are exceptional lawn mowers that combine efficiency, power, and user-friendly features. With their advanced technologies and robust design, these models stand out in the marketplace, making lawn care an achievable task for everyone, from novice gardeners to seasoned landscapers. Whether for residential or commercial use, these mowers offer reliability and performance to keep lawns looking their best.
Top Page Image Contents