Nilfisk-Advance America 56316026 (R32-C) manual 10 / English, Detergent System Preparation and USE

Page 10

A-10 / ENGLISH

DETERGENT SYSTEM PREPARATION AND USE

COMMON INSTRUCTIONS:

The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over floor drain before purging because a small amount of detergent will be dispensed in the process.

To Purge When Changing Chemicals:

1Disconnect and remove the detergent cartridge.

2Turn the Key Switch (J) ON and press the Detergent ON/OFF Switch (S) and the Flow Rate Switch (T) down for at least 3 seconds. NOTE: Once activated the Flow Rate Indicator (U) will begin to flash and will automatically shut off after 10 seconds. Normally one purge cycle is adequate to purge the system.

To Purge Weekly:

1Disconnect and remove the detergent cartridge. Install and connect a Cartridge filled with clean water

2Turn the Key Switch (J) ON and press the Detergent ON/OFF Switch (S) and the Flow Rate Switch (T) down for at least 3 seconds. NOTE: Once activated the Flow Rate Indicator (U) will begin to flash and will automatically shut off after 10 seconds. Normally one purge cycle is adequate to purge the system.

The Detergent Box (AA) has a Detergent Level Viewing Slot (BB) for keeping track of how much detergent is remaining in the cartridge. When the detergent level is nearing the bottom of this slot it is time to refill or replace the cartridge.

General Use:

The detergent (AXP/EDS) system is turned on when the Key Switch (J) is turned on but no detergent is dispensed until the scrub system is activated and the Drive Pedal (8) pushed forward. The solution flow rate automatically defaults to the last setting used. The solution flow rate can be varied by subsequently pressing the Flow Rate Switch (T). There are two solution flow rates indicated by the Flow Rate Indicator (U). The detergent flow rate increases or decreases with the solution flow rate but the detergent ratio remains the same. During scrubbing, the detergent system can be turned off at any time by pressing the Detergent ON/OFF Switch (S) to allow scrubbing with water only. The solution flow rate is controlled by the Flow Rate Switch (T) whether the detergent system is ON or OFF.

SERVICE NOTE: Follow the “To Purge Weekly” instructions above if the machine is going to be stored for an extended period of time or if you plan to discontinue use of the detergent (AXP/EDS) system.

NON-REFILLABLE CARTRIDGE SPECIFIC INSTRUCTIONS:

Remove the Cap (CC) and place the cartridge in the detergent box. Install the Dry Break Cap (DD) as shown.

REFILLABLE CARTRIDGE SPECIFIC INSTRUCTIONS:

Fill the detergent cartridge with a maximum of 1.25 gallons (4.73 Liters) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to filling to avoid spilling detergent on the machine.

It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the detergent name on each cartridge to avoid mixing them up. The detergent cartridge has a Magnetic Slider (EE) on one end that needs to be set to the proper dilution ratio according to the dilution instructions on the manufacturer’s bottle. Slide the Magnet Slider (EE) to the appropriate location on Detergent Dilution Ratio Decal (FF). When installing a new cartridge, remove the Cap (CC) and place the cartridge in the detergent box. Install the Dry Break Cap (DD) as shown.

A-10- 56041647 - Adhancer™ R28-C, R32-C / BR 800S TRIO EDS™

Page 9 Page 11
Image 10
Page 9 Page 11
Contents BR 800S Trio EDS English Symbols English / A-3Consignes DE Prudence ET DE Sécurité Symboles English / A-5 Charger Connector not found on all modelsKnow Your Machine Control Panel When Servicing Batteries Description of the Battery Condition IndicatorsInstall the Batteries English / A-7Install the Brushes Fill the Solution Tank Install the SqueegeeEnglish / A-9 Detergent System Preparation and USE To Purge When Changing Chemicals10 / English To Purge WeeklyEnglish / A-11 WET Vacuuming 12 / EnglishOperating the Machine To ScrubAfter USE Maintenance ScheduleEnglish / A-13 Lubricating the MachineCharging the Batteries Checking the Battery Electrolyte Level14 / English To Charge the BatteriesSqueegee Adjustment Squeegee MaintenanceEnglish / A-15 16 / English Side Skirt MaintenanceSide Skirt Height Adjustment To replace the scrub system side skirtsProblem Possible Cause Remedy General Machine TroubleshootingEnglish / A-17 18 / English Model Adhancer R28-C Adhancer R32-CPage Español Precauciones Y Advertencias Símbolos Español / B-3Conozca SU Máquina Español / B-5 Panel DE ControlEstándar Alternativo Descripción DE LOS Indicadores DE Situación DE LAS BateríasInstalación DE LAS Baterías Cuando revise las bateríasEspañol / B-7 Instalación DE LOS CepillosInstalación DE LA Boquilla Llenado DEL Depósito DE SoluciónEspañol / B-9 Reparación Y USO DEL Sistema DE Detergente10 / Español Aspiración EN Húmedo Español / B-11Manejo DE LA Máquina Para fregarPrograma DE Mantenimiento 12 / EspañolDespués DE LA Utilización Lubricación DE LA MáquinaComprobación DEL Nivel DE Electrolitos DE LAS Baterías Español / B-13Recarga DE Baterías Para cargar las bateríasAjuste DE LA Boquilla 14 / EspañolMantenimiento DE LA Boquilla Ajuste del ángulo de la boquillaMantenimiento DE LA Faldilla Lateral Español / B-15Ajuste DE LA Altura DE LA Faldilla Lateral 16 / Español Solución DE Problemas Generales DE LA MáquinaProblema Posible causa Solución Véase el manual de servicioEspañol / B-17 Adhancer R28-C Adhancer R32-C2007

56316025 (R32-C), 56316026 (R32-C) specifications

Nilfisk-Advance America has continued to push the boundaries of cleaning technology with the introduction of the R32-C series, specifically models 56316026 and 56316025. These commercial-grade scrubbers are engineered for efficiency and effectiveness in a variety of settings, from retail environments to large industrial spaces.

One of the standout features of the R32-C models is their robust cleaning performance, powered by advanced brush technologies. The machines are equipped with dual counter-rotating brushes that provide a thorough scrub, ensuring that even the most stubborn dirt and grime is effectively removed. This brush system is designed to maintain consistent contact with the surface, enhancing cleaning efficiency and allowing operators to achieve superior results with minimal effort.

Another notable aspect of these scrubbers is the integrated solution delivery system. This technology allows for precise control over water and detergent dispensing, reducing waste and improving overall cleaning effectiveness. Operators can easily adjust the solution flow based on the specific cleaning task, making these machines adaptable to various floor types and conditions.

User convenience is also a primary focus in the design of R32-C models. The intuitive control panel simplifies operation, allowing staff to quickly learn how to use the equipment without extensive training. Additionally, the ergonomic design of the machine ensures comfortable handling, even during prolonged cleaning sessions, which is crucial for maintaining productivity in high-traffic environments.

Durability is another hallmark of the Nilfisk-Advance R32-C series. Constructed with high-quality materials, these scrubbers are built to withstand the rigors of daily use. Their robust chassis and components contribute to lower maintenance costs and longer service life, a critical factor for businesses looking to make a wise investment in cleaning equipment.

In summary, Nilfisk-Advance America's R32-C scrubbers 56316026 and 56316025 represent a significant advancement in cleaning technology. With their powerful cleaning capabilities, user-friendly operation, and durable construction, these models are designed to deliver exceptional performance for a wide range of commercial cleaning tasks. They not only enhance cleaning efficiency but also contribute to a healthier and safer environment for staff and customers alike.
Top Page Image Contents