Craftsman 272, 410 owner manual Belts, Clean AIR Screen, Clean AIR INTAKE/COOLING Areas

Page 19

Keep battery and terminals clean. , Keep battery bolts tight.

, Keep small vent holes open.

, Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on /our tractor is maintenance free, Do not attempt to open or remove caps or covers. _dding or checking level of electrolyte is not necessary.

TO CLEAN BA'I-FERYAND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to "leak" power.

1.Open battery box door.

2.Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until bright.

5.Coat terminals with grease or petro- leum jelly.

6.Reinstall battery (See "REPLACING

BATTERY" in the SERVICE AND ADJUSTMENTS section of this

manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable.

Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated

NithAPI service classificationSF-SJ.

Select the oil'sSAE viscosity grade according to your expected operating :emperature.

TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

1.Remove oil fill cap/dipstick. Be careful not to allow did to enter the engine when changing oil.

2.Remove cap from end of drain valve and install the drain tube onto the fitting.

3.Unlock drain valve by pushing inward slightly and turning counterclcokwise.

4.To open, pug out on the drain valve.

5.After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

6.Remove the drain tube and replace

the cap onto to the end of the drain valve.

7.Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see

"PRODUCT SPECIFICATIONS" section of this manual

8.Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oilfill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at "FULL" line on dipstick. Tighten cap onto the tube securely when finished.

OilDrainValve

Closed and

Locked (

 

Posit_on ::;.]..

rain Tube

 

c

 

CLEAN AIR SCREEN

 

.m

o

_ m _

m

im

iw

Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before starting the engine and after each eight

(8) hours of operation. Tighten oil fill cap/

dipsticksecurely each time you check the oil level.

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

19

Image 19
Contents Icraftsmawj Limited 90 DAY Warranty on BAI-FERY WarrantyII. Slope Operation General OperationDo not Mower blades are sharp and can cut IV. ServiceCancer and birth defects or other repro- ductive harm 3RD Battery AMP/HR MIN. CCAAPI-SF-SJ 3ROUND Speed ForwardOpeShIIl.e Before Removingtractor from Skid Tools Required For AssemblyTo Removetractor from Carton Unpack Carton Install Seat Check for Proper Position of ALL B Elts To Convertto Bagging or DischargingChecktire Pressure Check Deck LevelnessEHO,NEOHENG,HEOFFOILPeESSUnEL,ONTSOOVI,.MP Knowyourtractor Our tractors conform to the safety standardsAmmeter Engine Howto Useyourtractor To SET Parking BrakeMower Blades Ground DriveTo Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsTo Start Engine Towing Carts and Other AttachmentsBefore Starting the Engine Check Engine OIL Level ADD GasolineTion of clippings and more uniform cutting Level Mower Housing Service and Adjustments section of thisMowing Tips Left hand side of mower should be used for trimmingBefore Each USE General RecommendationsSection Operator Presence System TractorBrake Operation TiresClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts Engine OIL Filter AIR FilterMuffler Spark PlugsTo Install Mower CleaningTractor To Remove Mower Belt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Belt InstallationTo Adjust Brake Transaxle Gear Shift Lever Neutral AdjustmentTo AI-IACHJUMPER Cables To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Replace Fuse To Adjust Throfflecontrol CableTo Replace Headlight Bulb Interlocks and RelaysAcceleration Test To Adjust CarburetorOther Engine Fuel SystemEngine OIL CylindersCause ProblemCorrection Troubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause Correction Schmatc RRACTOR - Model NumberTRACTOR- -MODEL Number Electrical Tractor - Model NumberTRACTOR- -MODEL Number Chassis and Enclosures KEY Part Description TRACTOR-- Model Number 917.272410 Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive X .1845/1865 TRACTOR-- Model Number Ground DriveTRACTOR--MODELNUMBER917.272410 Steeringassembly KEY Part NO. NO. Description TRACTORMODELNUMBER917--.272410 SteeringassemblyOptional Equipment Spark ArresterTRACTOR- Model Number KEY Part NO. NO.DESCRIPON TRACTOR--MODEL Number Seat AssemblyDecals TRACTOR-- Model NumberWheels &TIRES TRACTOR--MODELNUMBER917.272410 Liftassembly TRACTOR-- Model Number Lift Assembly TRACTORMODELNUMBER917--.272410 Mowerdeck Tractor --MODEL Number 917,272410 Mowerdeck PEERLESSTRANSAXLE- Model NUMBER206-545C TRACTOR-- MODELNUMBER917.272410ORing Crankcase I CARTER-MOTEUR Ram Crankcase KEY Part NO. no DescriptionBlower Housing and Baffles Not Illustrated KEY Part NO. no DescriptionAIR INTAKE/FILTRATION KEY Part Description NO. no OIL PAN / Lubrication KEY Part NO, no Starting SystemFuel System UEL DE LE Systime ItlCrankshaft KEY Part NO. no Fuel System KEY Part NO. noExhaust KEY Part NO. no Description Page Sighting Only Ride UP and Down Hill Not Across HillGuideth Part Anyme,ctyorrt U.SAiy

272, 410 specifications

The Craftsman 410,272 is a versatile and powerful tool designed for both DIY enthusiasts and professional craftsmen. This product epitomizes the careful blend of innovative technology and user-friendly features, making it a popular choice in the woodworking and construction sectors.

One of the standout characteristics of the Craftsman 410,272 is its robust motor. With a high-performance engine, it delivers exceptional torque, allowing users to tackle a wide range of applications with ease. From cutting and drilling to sanding and shaping, this tool ensures you achieve precise results in a fraction of the time compared to traditional methods.

In terms of design, the Craftsman 410,272 boasts an ergonomic handle that enhances comfort during prolonged use. This thoughtful design reduces hand fatigue and allows for better control, resulting in improved accuracy. The lightweight construction also makes it easily portable, so you can take it wherever your projects lead you.

Another noteworthy feature is the integrated tool storage. This clever addition allows users to keep their equipment organized and readily accessible, minimizing downtime during tasks. The quick-release mechanism simplifies the swapping of attachments, enhancing versatility and productivity.

Craftsman has incorporated advanced safety features into the 410,272, ensuring that you can work confidently. The safety guard prevents accidental injuries, while the variable speed control allows you to adjust the tool’s performance according to the material you are working with. This level of adaptability is essential for achieving optimal results on different surfaces.

The Craftsman 410,272 is also compatible with a wide array of attachments and accessories, making it an all-in-one solution for various projects. Whether you need to drill, cut, or finish, you can customize the tool to meet your specific requirements.

In conclusion, the Craftsman 410,272 stands out for its powerful motor, ergonomic design, integrated storage, safety features, and compatibility with various attachments. It is engineered to provide efficiency and precision, making it an invaluable addition to any workshop or job site. With its combination of performance and versatility, this tool is sure to enhance your craftsmanship, whether you are a seasoned professional or just starting your journey in the world of DIY projects. Craftsmanship has never been easier or more reliable.