Craftsman 410, 272 owner manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 24

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructionsin the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are

not adjustable on your tractor. If damage has occurred to affect the front wheel toe-

in or camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1.BIcok up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle.

Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. "13resealant also prevents tire dry rot and corrosion.

IMPORTANT: Your tractor is equipped with a 12 volt negative grounded system. The other vehical must also be a 12 volt

negative grounded system. Do not use your tractor battery to start other vehicles.

TO A'I-I'ACHJUMPER CABLES -

1.Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

3.Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuet tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

Positive Terminal

Negative Terminal

RetainingA

A

Charged

Battery

Positive Terminal

Negative Terminal

REPLACING BA'i-I'ERY

_,CAUTION: Do not short battery

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATI'ERY

_CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY"in the MAINTENANCE section of this manual).

If "jumper cables" are used for emergency starting, follow this procedure:

terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch

bands, rings, etc.

Positive terminal must be connected first

to prevent sparking from accidental grounding.

1.Lift seat pan to raised position and open battery box door.

2.Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

24

Image 24
Contents Icraftsmawj Warranty Limited 90 DAY Warranty on BAI-FERYGeneral Operation II. Slope OperationDo not IV. Service Mower blades are sharp and can cutCancer and birth defects or other repro- ductive harm Battery AMP/HR MIN. CCA API-SF-SJ3ROUND Speed Forward 3RDOpeShIIl.e Tools Required For Assembly Before Removingtractor from SkidTo Removetractor from Carton Unpack Carton Install Seat To Convertto Bagging or Discharging Checktire PressureCheck Deck Levelness Check for Proper Position of ALL B EltsEHO,NEOHENG,HEOFFOILPeESSUnEL,ONTSOOVI,.MP Our tractors conform to the safety standards KnowyourtractorAmmeter Howto Useyourtractor To SET Parking Brake Mower BladesGround Drive EngineTo Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportTowing Carts and Other Attachments Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start EngineLevel Mower Housing Service and Adjustments section of this Mowing TipsLeft hand side of mower should be used for trimming Tion of clippings and more uniform cuttingGeneral Recommendations Before Each USESection Tractor Brake OperationTires Operator Presence SystemClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts AIR Filter MufflerSpark Plugs Engine OIL FilterCleaning To Install MowerTractor To Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Blade Drive Belt Belt RemovalBelt Installation To Adjust BrakeTransaxle Gear Shift Lever Neutral Adjustment To Replace Motion Drive BeltTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs To AI-IACHJUMPER CablesTo Adjust Throfflecontrol Cable To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Adjust Carburetor Acceleration TestEngine Fuel System Engine OILCylinders OtherProblem CauseCorrection Troubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause Correction RRACTOR - Model Number SchmatcTRACTOR- -MODEL Number Tractor - Model Number ElectricalTRACTOR- -MODEL Number Chassis and Enclosures TRACTOR-- Model Number 917.272410 Chassis and Enclosures KEY Part DescriptionTRACTOR--MODEL Number Ground Drive TRACTOR-- Model Number Ground Drive X .1845/1865TRACTOR--MODELNUMBER917.272410 Steeringassembly TRACTORMODELNUMBER917--.272410 Steeringassembly KEY Part NO. NO. DescriptionSpark Arrester Optional EquipmentTRACTOR- Model Number TRACTOR--MODEL Number Seat Assembly KEY Part NO. NO.DESCRIPONTRACTOR-- Model Number DecalsWheels &TIRES TRACTOR--MODELNUMBER917.272410 Liftassembly TRACTOR-- Model Number Lift Assembly TRACTORMODELNUMBER917--.272410 Mowerdeck Tractor --MODEL Number 917,272410 Mowerdeck TRACTOR-- MODELNUMBER917.272410 PEERLESSTRANSAXLE- Model NUMBER206-545CORing Crankcase I CARTER-MOTEUR Crankcase KEY Part NO. no Description RamBlower Housing and Baffles KEY Part NO. no Description Not IllustratedAIR INTAKE/FILTRATION KEY Part Description NO. no OIL PAN / Lubrication Starting System KEY Part NO, noItl Fuel System UEL DE LE SystimeFuel System KEY Part NO. no Crankshaft KEY Part NO. noExhaust KEY Part NO. no Description Page Only Ride UP and Down Hill Not Across Hill SightingGuideth Anyme,ctyorrt U.SAiy Part

272, 410 specifications

The Craftsman 410,272 is a versatile and powerful tool designed for both DIY enthusiasts and professional craftsmen. This product epitomizes the careful blend of innovative technology and user-friendly features, making it a popular choice in the woodworking and construction sectors.

One of the standout characteristics of the Craftsman 410,272 is its robust motor. With a high-performance engine, it delivers exceptional torque, allowing users to tackle a wide range of applications with ease. From cutting and drilling to sanding and shaping, this tool ensures you achieve precise results in a fraction of the time compared to traditional methods.

In terms of design, the Craftsman 410,272 boasts an ergonomic handle that enhances comfort during prolonged use. This thoughtful design reduces hand fatigue and allows for better control, resulting in improved accuracy. The lightweight construction also makes it easily portable, so you can take it wherever your projects lead you.

Another noteworthy feature is the integrated tool storage. This clever addition allows users to keep their equipment organized and readily accessible, minimizing downtime during tasks. The quick-release mechanism simplifies the swapping of attachments, enhancing versatility and productivity.

Craftsman has incorporated advanced safety features into the 410,272, ensuring that you can work confidently. The safety guard prevents accidental injuries, while the variable speed control allows you to adjust the tool’s performance according to the material you are working with. This level of adaptability is essential for achieving optimal results on different surfaces.

The Craftsman 410,272 is also compatible with a wide array of attachments and accessories, making it an all-in-one solution for various projects. Whether you need to drill, cut, or finish, you can customize the tool to meet your specific requirements.

In conclusion, the Craftsman 410,272 stands out for its powerful motor, ergonomic design, integrated storage, safety features, and compatibility with various attachments. It is engineered to provide efficiency and precision, making it an invaluable addition to any workshop or job site. With its combination of performance and versatility, this tool is sure to enhance your craftsmanship, whether you are a seasoned professional or just starting your journey in the world of DIY projects. Craftsmanship has never been easier or more reliable.