Craftsman 272, 410 owner manual Cleaning, Tractor To Remove Mower, To Install Mower

Page 21

3.Be sure there are no fuel line leaks and clamps are properly positioned.

4.Immediately wipe up any spilled gasoline,

Clam_Clamp

Fuel FIItar-'f_

CLEANING

Keep finished surfaces and wheels free of all gasoline, oil, etc.

Protect painted surfaces with automo- tive type wax.

We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in a shortened

engine life.

Clean engine, battery, seat, finish, etc. of all foreign matter.

1,CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

1.Depress clutch/brake pedal fully and set parking brake.

2.Place gearshift lever in neutral (N) position,

3.Place attachment clutch in "DISENGAGED" position.

4.Turn ignition key "OFF" and remove key.

5, Make sure the blades and all moving parts have completely stopped.

6, Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the right side of tractor.

1.Place attachment clutch switch in "DISENGAGED" position.

2.Move attachment lift lever forward to lower mower to its lowest position.

3.Roll belt oft electric clutch pulley.

4.Disconnect anti-sway bar from chassis bracket by removing retainer spring.

5.Disconnect suspension arms from rear deck brackets by removing retainer springs.

6.Disconnect front links from deck by removing retainer springs.

Srnall Retainer

Retainer

Ant_-Sway

7.Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links,

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflector shield to right side of tractor.

3.Lower lift lever to its lowest position. 4, Install mower in reverse order of

removal instructions.

Electric

Suspension

ArmsPulley

Front Link

;prings

(Both Sides)

Retainer Spring

21

Image 21
Contents Icraftsmawj Limited 90 DAY Warranty on BAI-FERY WarrantyGeneral Operation II. Slope OperationDo not Mower blades are sharp and can cut IV. ServiceCancer and birth defects or other repro- ductive harm API-SF-SJ Battery AMP/HR MIN. CCA3ROUND Speed Forward 3RDOpeShIIl.e Tools Required For Assembly Before Removingtractor from SkidTo Removetractor from Carton Unpack Carton Install Seat Checktire Pressure To Convertto Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL B EltsEHO,NEOHENG,HEOFFOILPeESSUnEL,ONTSOOVI,.MP Our tractors conform to the safety standards KnowyourtractorAmmeter Mower Blades Howto Useyourtractor To SET Parking BrakeGround Drive EngineTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other AttachmentsADD Gasoline To Start EngineMowing Tips Level Mower Housing Service and Adjustments section of thisLeft hand side of mower should be used for trimming Tion of clippings and more uniform cuttingGeneral Recommendations Before Each USESection Brake Operation TractorTires Operator Presence SystemClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts Muffler AIR FilterSpark Plugs Engine OIL FilterCleaning To Install MowerTractor To Remove Mower SIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Adjust Brake Belt InstallationTransaxle Gear Shift Lever Neutral Adjustment To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Remove Wheel for Repairs To AI-IACHJUMPER CablesTo Replace Headlight Bulb To Adjust Throfflecontrol CableInterlocks and Relays To Replace FuseAcceleration Test To Adjust CarburetorEngine OIL Engine Fuel SystemCylinders OtherProblem CauseCorrection Troubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause Correction Schmatc RRACTOR - Model NumberTRACTOR- -MODEL Number Electrical Tractor - Model NumberTRACTOR- -MODEL Number Chassis and Enclosures KEY Part Description TRACTOR-- Model Number 917.272410 Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive X .1845/1865 TRACTOR-- Model Number Ground DriveTRACTOR--MODELNUMBER917.272410 Steeringassembly KEY Part NO. NO. Description TRACTORMODELNUMBER917--.272410 SteeringassemblyOptional Equipment Spark ArresterTRACTOR- Model Number KEY Part NO. NO.DESCRIPON TRACTOR--MODEL Number Seat AssemblyTRACTOR-- Model Number DecalsWheels &TIRES TRACTOR--MODELNUMBER917.272410 Liftassembly TRACTOR-- Model Number Lift Assembly TRACTORMODELNUMBER917--.272410 Mowerdeck Tractor --MODEL Number 917,272410 Mowerdeck PEERLESSTRANSAXLE- Model NUMBER206-545C TRACTOR-- MODELNUMBER917.272410ORing Crankcase I CARTER-MOTEUR Ram Crankcase KEY Part NO. no DescriptionBlower Housing and Baffles KEY Part NO. no Description Not IllustratedAIR INTAKE/FILTRATION KEY Part Description NO. no OIL PAN / Lubrication KEY Part NO, no Starting SystemFuel System UEL DE LE Systime ItlFuel System KEY Part NO. no Crankshaft KEY Part NO. noExhaust KEY Part NO. no Description Page Only Ride UP and Down Hill Not Across Hill SightingGuideth Part Anyme,ctyorrt U.SAiy

272, 410 specifications

The Craftsman 410,272 is a versatile and powerful tool designed for both DIY enthusiasts and professional craftsmen. This product epitomizes the careful blend of innovative technology and user-friendly features, making it a popular choice in the woodworking and construction sectors.

One of the standout characteristics of the Craftsman 410,272 is its robust motor. With a high-performance engine, it delivers exceptional torque, allowing users to tackle a wide range of applications with ease. From cutting and drilling to sanding and shaping, this tool ensures you achieve precise results in a fraction of the time compared to traditional methods.

In terms of design, the Craftsman 410,272 boasts an ergonomic handle that enhances comfort during prolonged use. This thoughtful design reduces hand fatigue and allows for better control, resulting in improved accuracy. The lightweight construction also makes it easily portable, so you can take it wherever your projects lead you.

Another noteworthy feature is the integrated tool storage. This clever addition allows users to keep their equipment organized and readily accessible, minimizing downtime during tasks. The quick-release mechanism simplifies the swapping of attachments, enhancing versatility and productivity.

Craftsman has incorporated advanced safety features into the 410,272, ensuring that you can work confidently. The safety guard prevents accidental injuries, while the variable speed control allows you to adjust the tool’s performance according to the material you are working with. This level of adaptability is essential for achieving optimal results on different surfaces.

The Craftsman 410,272 is also compatible with a wide array of attachments and accessories, making it an all-in-one solution for various projects. Whether you need to drill, cut, or finish, you can customize the tool to meet your specific requirements.

In conclusion, the Craftsman 410,272 stands out for its powerful motor, ergonomic design, integrated storage, safety features, and compatibility with various attachments. It is engineered to provide efficiency and precision, making it an invaluable addition to any workshop or job site. With its combination of performance and versatility, this tool is sure to enhance your craftsmanship, whether you are a seasoned professional or just starting your journey in the world of DIY projects. Craftsmanship has never been easier or more reliable.