Craftsman 272, 410 owner manual Belt Installation, To Adjust Brake, To Replace Motion Drive Belt

Page 23

BELT INSTALLATION -

4.Install new belt in reverse order of removal.

5.Make sure bolt is in all pulley grooves and inside all belt guides.

6.Install mower in reverse order of removal instructions.

Mandrel

Mandrel

TO ADJUST BRAKE

Your tractor is equipped with an adjust- able brake system which is mounted on the right side of the transaxle.

If tractorrequires more than six (6) feet stoppingdistance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

1.Depress clutch/brake pedal and engage parking brake.

2.Measure distance between brake

operating arm and nut =A" on brake rod.

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a

bolt installation guide decal on bottom side of left footrest.

1.Remove mower (See "TO REMOVE

MOWER" in this section of this manual.)

2.Disconnect clutch wire harness.

3.Remove clutch leeator.

4.Remove belt from stationary idler and clutching idler,

5.Pull belt slack toward rear of tractor.

Remove bert upwards from transaxle pulley by deflecting belt keepers.

6.Pull belt toward frontof tractor and remove downwards from around electric clutch,

7.Install new belt by reversing above procedure.

Clutch

Electdc/Locater Clutch

Clutching /

Idler

Stationary /

Idler

Y

3.If distance is other than 1-1/2 =, loosen jam nut and turn nut "A"until distance becomes 1-1/2". Retightenjam nut against nut "A".

4.Road test tractor for proper stopping distance as stated above. Readjust if necessary, If stopping distance is still greater than six (6) feet in highest gear, further maintenance is neces- sary. Contact a Sears or other qualified service center.

With Parking Brake "Engaged"

1"1/2=

Nut "A"

Jam Nut

_ting

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (leek gate) position.The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transax]e is in neutral (N),

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

2.Loosen adjustment bolt in front of the right rear wheel,

3, Position the gear shift lever in the neutral (N) position.

4.Tighten adjustment bolt securely. NOTE: if additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GearshiftNeutralLockGate

23

! Adjustment Bolt

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Icraftsmawj Limited 90 DAY Warranty on BAI-FERY WarrantyDo not General OperationII. Slope Operation Mower blades are sharp and can cut IV. ServiceCancer and birth defects or other repro- ductive harm 3RD Battery AMP/HR MIN. CCAAPI-SF-SJ 3ROUND Speed ForwardOpeShIIl.e To Removetractor from Carton Unpack Carton Tools Required For AssemblyBefore Removingtractor from Skid Install Seat Check for Proper Position of ALL B Elts To Convertto Bagging or DischargingChecktire Pressure Check Deck LevelnessEHO,NEOHENG,HEOFFOILPeESSUnEL,ONTSOOVI,.MP Ammeter Our tractors conform to the safety standardsKnowyourtractor Engine Howto Useyourtractor To SET Parking BrakeMower Blades Ground DriveTo Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsTo Start Engine Towing Carts and Other AttachmentsBefore Starting the Engine Check Engine OIL Level ADD GasolineTion of clippings and more uniform cutting Level Mower Housing Service and Adjustments section of thisMowing Tips Left hand side of mower should be used for trimmingSection General RecommendationsBefore Each USE Operator Presence System TractorBrake Operation TiresBelts Clean AIR ScreenClean AIR INTAKE/COOLING Areas Engine OIL Filter AIR FilterMuffler Spark PlugsTractor To Remove Mower CleaningTo Install Mower Belt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Belt InstallationTo Adjust Brake Transaxle Gear Shift Lever Neutral AdjustmentTo AI-IACHJUMPER Cables To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Replace Fuse To Adjust Throfflecontrol CableTo Replace Headlight Bulb Interlocks and RelaysAcceleration Test To Adjust CarburetorOther Engine Fuel SystemEngine OIL CylindersCorrection ProblemCause Troubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause Correction Schmatc RRACTOR - Model NumberTRACTOR- -MODEL Number Electrical Tractor - Model NumberTRACTOR- -MODEL Number Chassis and Enclosures KEY Part Description TRACTOR-- Model Number 917.272410 Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive X .1845/1865 TRACTOR-- Model Number Ground DriveTRACTOR--MODELNUMBER917.272410 Steeringassembly KEY Part NO. NO. Description TRACTORMODELNUMBER917--.272410 SteeringassemblyOptional Equipment Spark ArresterTRACTOR- Model Number KEY Part NO. NO.DESCRIPON TRACTOR--MODEL Number Seat AssemblyWheels &TIRES TRACTOR-- Model NumberDecals TRACTOR--MODELNUMBER917.272410 Liftassembly TRACTOR-- Model Number Lift Assembly TRACTORMODELNUMBER917--.272410 Mowerdeck Tractor --MODEL Number 917,272410 Mowerdeck PEERLESSTRANSAXLE- Model NUMBER206-545C TRACTOR-- MODELNUMBER917.272410ORing Crankcase I CARTER-MOTEUR Ram Crankcase KEY Part NO. no DescriptionBlower Housing and Baffles AIR INTAKE/FILTRATION KEY Part Description NO. no KEY Part NO. no DescriptionNot Illustrated OIL PAN / Lubrication KEY Part NO, no Starting SystemFuel System UEL DE LE Systime ItlExhaust KEY Part NO. no Description Fuel System KEY Part NO. noCrankshaft KEY Part NO. no Page Guideth Only Ride UP and Down Hill Not Across HillSighting Part Anyme,ctyorrt U.SAiy

272, 410 specifications

The Craftsman 410,272 is a versatile and powerful tool designed for both DIY enthusiasts and professional craftsmen. This product epitomizes the careful blend of innovative technology and user-friendly features, making it a popular choice in the woodworking and construction sectors.

One of the standout characteristics of the Craftsman 410,272 is its robust motor. With a high-performance engine, it delivers exceptional torque, allowing users to tackle a wide range of applications with ease. From cutting and drilling to sanding and shaping, this tool ensures you achieve precise results in a fraction of the time compared to traditional methods.

In terms of design, the Craftsman 410,272 boasts an ergonomic handle that enhances comfort during prolonged use. This thoughtful design reduces hand fatigue and allows for better control, resulting in improved accuracy. The lightweight construction also makes it easily portable, so you can take it wherever your projects lead you.

Another noteworthy feature is the integrated tool storage. This clever addition allows users to keep their equipment organized and readily accessible, minimizing downtime during tasks. The quick-release mechanism simplifies the swapping of attachments, enhancing versatility and productivity.

Craftsman has incorporated advanced safety features into the 410,272, ensuring that you can work confidently. The safety guard prevents accidental injuries, while the variable speed control allows you to adjust the tool’s performance according to the material you are working with. This level of adaptability is essential for achieving optimal results on different surfaces.

The Craftsman 410,272 is also compatible with a wide array of attachments and accessories, making it an all-in-one solution for various projects. Whether you need to drill, cut, or finish, you can customize the tool to meet your specific requirements.

In conclusion, the Craftsman 410,272 stands out for its powerful motor, ergonomic design, integrated storage, safety features, and compatibility with various attachments. It is engineered to provide efficiency and precision, making it an invaluable addition to any workshop or job site. With its combination of performance and versatility, this tool is sure to enhance your craftsmanship, whether you are a seasoned professional or just starting your journey in the world of DIY projects. Craftsmanship has never been easier or more reliable.
Top Page Image Contents