Craftsman 272, 410 owner manual Troubleshooting Chart Problem Cause

Page 29

TROUBLESHOOTING

 

CHART

PROBLEM

CAUSE

Loss of power

1.

Cutting too much grass/too

 

 

fast.

 

2.

Throttle in"CHOKE"

 

 

position.

 

3.

Build-up of grass, leaves

 

 

and trash under mower.

 

4.

Dirty air filter.

 

5.

Low oil leveVdirty oil.

 

6.

Faulty spark plug.

 

7.

Dirty fuel filter.

 

8.

Stale or dirtyfuel.

 

9.

Water in fuel.

10.Spark plug wire loose.

11.Dirty engine air screen/fins.

12.Dirty/clogged muffler. 13.Loose or damaged wiring.

14.Carburetor out of

CORRECTION

1.Set in "Higher Cut" position/ reduce speed.

2.Adjust throttle control

3.Clean underside of mower housing.

4.Clean/replace air filter.

5.Check oil level/change oil.

6.Clean and regap or change spark plug.

7.Replace fuel filter.

8.Drain fuel tank and refill with fresh gasoline.

9.Drain fuel tank and carbure tor, refill tank with fresh

gasoline and replace fuel filter.

10.Connect and tighten spark plug wire.

11.Clean engine air screen/fins. 12.ClearVreplace muffler. 13.Check all wiring.

14. See "To Adjust Carburetor"

Excessive vibration

Engine continues to run

when operator leaves seat with with attachment

clutch engaged

adjustment.

15.Engine valves out of adjustment.

1.Worn, bent or loose blade.

2.Bent blade mandrel.

3.Loose/damaged part(s).

1.Faulty operator-safety presence control system.

in Service Adjustments

section.

15.Contact a Sears or other qualified service center.

1.Replace blade. Tighten blade bolt.

2.Replace blade mandrel.

3.Tighten loose part(s). Replace damaged parts.

1.Check wiring, switches and connections. If not contact a Sears or other qualified service center.

Poor cut - uneven t. Worn, bent or loose blade.

2.Mower deck not level.

3.Buildup of grass, leaves, and trash under mower.

4, Bent blade mandrel.

5.Clogged mower deck vent holes from buildup of

grass, leaves, and trash around mandrels.

1.Replace blade. Tighten blade bolt.

2.Level mower deck.

3.Clean underside of mower housing.

4.Replace blade mandrel.

5.Clean around mandrels to open vent holes.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Icraftsmawj Limited 90 DAY Warranty on BAI-FERY WarrantyDo not General OperationII. Slope Operation Mower blades are sharp and can cut IV. ServiceCancer and birth defects or other repro- ductive harm API-SF-SJ Battery AMP/HR MIN. CCA3ROUND Speed Forward 3RDOpeShIIl.e To Removetractor from Carton Unpack Carton Tools Required For AssemblyBefore Removingtractor from Skid Install Seat Checktire Pressure To Convertto Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL B EltsEHO,NEOHENG,HEOFFOILPeESSUnEL,ONTSOOVI,.MP Ammeter Our tractors conform to the safety standardsKnowyourtractor Mower Blades Howto Useyourtractor To SET Parking BrakeGround Drive EngineTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other AttachmentsADD Gasoline To Start EngineMowing Tips Level Mower Housing Service and Adjustments section of thisLeft hand side of mower should be used for trimming Tion of clippings and more uniform cuttingSection General RecommendationsBefore Each USE Brake Operation TractorTires Operator Presence SystemBelts Clean AIR ScreenClean AIR INTAKE/COOLING Areas Muffler AIR FilterSpark Plugs Engine OIL FilterTractor To Remove Mower CleaningTo Install Mower SIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Adjust Brake Belt InstallationTransaxle Gear Shift Lever Neutral Adjustment To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Remove Wheel for Repairs To AI-IACHJUMPER CablesTo Replace Headlight Bulb To Adjust Throfflecontrol CableInterlocks and Relays To Replace FuseAcceleration Test To Adjust CarburetorEngine OIL Engine Fuel SystemCylinders OtherCorrection ProblemCause Troubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause Correction Schmatc RRACTOR - Model NumberTRACTOR- -MODEL Number Electrical Tractor - Model NumberTRACTOR- -MODEL Number Chassis and Enclosures KEY Part Description TRACTOR-- Model Number 917.272410 Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive X .1845/1865 TRACTOR-- Model Number Ground DriveTRACTOR--MODELNUMBER917.272410 Steeringassembly KEY Part NO. NO. Description TRACTORMODELNUMBER917--.272410 SteeringassemblyOptional Equipment Spark ArresterTRACTOR- Model Number KEY Part NO. NO.DESCRIPON TRACTOR--MODEL Number Seat AssemblyWheels &TIRES TRACTOR-- Model NumberDecals TRACTOR--MODELNUMBER917.272410 Liftassembly TRACTOR-- Model Number Lift Assembly TRACTORMODELNUMBER917--.272410 Mowerdeck Tractor --MODEL Number 917,272410 Mowerdeck PEERLESSTRANSAXLE- Model NUMBER206-545C TRACTOR-- MODELNUMBER917.272410ORing Crankcase I CARTER-MOTEUR Ram Crankcase KEY Part NO. no DescriptionBlower Housing and Baffles AIR INTAKE/FILTRATION KEY Part Description NO. no KEY Part NO. no DescriptionNot Illustrated OIL PAN / Lubrication KEY Part NO, no Starting SystemFuel System UEL DE LE Systime ItlExhaust KEY Part NO. no Description Fuel System KEY Part NO. noCrankshaft KEY Part NO. no Page Guideth Only Ride UP and Down Hill Not Across HillSighting Part Anyme,ctyorrt U.SAiy

272, 410 specifications

The Craftsman 410,272 is a versatile and powerful tool designed for both DIY enthusiasts and professional craftsmen. This product epitomizes the careful blend of innovative technology and user-friendly features, making it a popular choice in the woodworking and construction sectors.

One of the standout characteristics of the Craftsman 410,272 is its robust motor. With a high-performance engine, it delivers exceptional torque, allowing users to tackle a wide range of applications with ease. From cutting and drilling to sanding and shaping, this tool ensures you achieve precise results in a fraction of the time compared to traditional methods.

In terms of design, the Craftsman 410,272 boasts an ergonomic handle that enhances comfort during prolonged use. This thoughtful design reduces hand fatigue and allows for better control, resulting in improved accuracy. The lightweight construction also makes it easily portable, so you can take it wherever your projects lead you.

Another noteworthy feature is the integrated tool storage. This clever addition allows users to keep their equipment organized and readily accessible, minimizing downtime during tasks. The quick-release mechanism simplifies the swapping of attachments, enhancing versatility and productivity.

Craftsman has incorporated advanced safety features into the 410,272, ensuring that you can work confidently. The safety guard prevents accidental injuries, while the variable speed control allows you to adjust the tool’s performance according to the material you are working with. This level of adaptability is essential for achieving optimal results on different surfaces.

The Craftsman 410,272 is also compatible with a wide array of attachments and accessories, making it an all-in-one solution for various projects. Whether you need to drill, cut, or finish, you can customize the tool to meet your specific requirements.

In conclusion, the Craftsman 410,272 stands out for its powerful motor, ergonomic design, integrated storage, safety features, and compatibility with various attachments. It is engineered to provide efficiency and precision, making it an invaluable addition to any workshop or job site. With its combination of performance and versatility, this tool is sure to enhance your craftsmanship, whether you are a seasoned professional or just starting your journey in the world of DIY projects. Craftsmanship has never been easier or more reliable.
Top Page Image Contents