Craftsman 272, 410 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 25

5.Connect BLACK grounding cable to negative (-) terminal with remaining

hex bolt and keps nut. Tighten

Hood

securely.

\

6. Close battery box door.

 

Battery

Door

Hsx

Nut

Positive (Red) Cable

Negative (Black)

 

Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiringmay cause your tractorto run poorly,stop running, or prevent it from starting.

Chock wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse, The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in frontof tractor. Grasp hood at

sides, tilt toward engine and lift oft of tractor.

4.To replace, reverse above procedure.

W,re

ENGINE

Maintenance, repair, or replacement of the emission control devices and sys- tems, which are being done at the customers expense, may be performed by any non-road engine repair establish- ment or individual. Warranty repairs must be performed by an authodzed engine manufacturer's service outlet.

TO ADJUST THRO'FFLECONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as de- scribed below before loosening cable. If adjustment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

2.Chock to see if hole in throttle lever

and hole in speed control bracket are aligned.

3.If holes are not aligned, loosen cable clamp screw and align the holes by inserting a pencil or a 1/4" drill bit through both holes.

4.Pull throttle cable up to remove slack and tighten cable clamp screw. Remove alignment pencil or drill bit.

Cable

Screw

Speed Control

Throffiel

25

Image 25
Contents Icraftsmawj Limited 90 DAY Warranty on BAI-FERY WarrantyII. Slope Operation General OperationDo not Mower blades are sharp and can cut IV. ServiceCancer and birth defects or other repro- ductive harm API-SF-SJ Battery AMP/HR MIN. CCA3ROUND Speed Forward 3RDOpeShIIl.e Before Removingtractor from Skid Tools Required For AssemblyTo Removetractor from Carton Unpack Carton Install Seat Checktire Pressure To Convertto Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL B EltsEHO,NEOHENG,HEOFFOILPeESSUnEL,ONTSOOVI,.MP Knowyourtractor Our tractors conform to the safety standardsAmmeter Mower Blades Howto Useyourtractor To SET Parking BrakeGround Drive EngineTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other AttachmentsADD Gasoline To Start EngineMowing Tips Level Mower Housing Service and Adjustments section of thisLeft hand side of mower should be used for trimming Tion of clippings and more uniform cuttingBefore Each USE General RecommendationsSection Brake Operation TractorTires Operator Presence SystemClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts Muffler AIR FilterSpark Plugs Engine OIL FilterTo Install Mower CleaningTractor To Remove Mower SIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Adjust Brake Belt InstallationTransaxle Gear Shift Lever Neutral Adjustment To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Remove Wheel for Repairs To AI-IACHJUMPER CablesTo Replace Headlight Bulb To Adjust Throfflecontrol CableInterlocks and Relays To Replace FuseAcceleration Test To Adjust CarburetorEngine OIL Engine Fuel SystemCylinders OtherCause ProblemCorrection Troubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause Correction Schmatc RRACTOR - Model NumberTRACTOR- -MODEL Number Electrical Tractor - Model NumberTRACTOR- -MODEL Number Chassis and Enclosures KEY Part Description TRACTOR-- Model Number 917.272410 Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive X .1845/1865 TRACTOR-- Model Number Ground DriveTRACTOR--MODELNUMBER917.272410 Steeringassembly KEY Part NO. NO. Description TRACTORMODELNUMBER917--.272410 SteeringassemblyOptional Equipment Spark ArresterTRACTOR- Model Number KEY Part NO. NO.DESCRIPON TRACTOR--MODEL Number Seat AssemblyDecals TRACTOR-- Model NumberWheels &TIRES TRACTOR--MODELNUMBER917.272410 Liftassembly TRACTOR-- Model Number Lift Assembly TRACTORMODELNUMBER917--.272410 Mowerdeck Tractor --MODEL Number 917,272410 Mowerdeck PEERLESSTRANSAXLE- Model NUMBER206-545C TRACTOR-- MODELNUMBER917.272410ORing Crankcase I CARTER-MOTEUR Ram Crankcase KEY Part NO. no DescriptionBlower Housing and Baffles Not Illustrated KEY Part NO. no DescriptionAIR INTAKE/FILTRATION KEY Part Description NO. no OIL PAN / Lubrication KEY Part NO, no Starting SystemFuel System UEL DE LE Systime ItlCrankshaft KEY Part NO. no Fuel System KEY Part NO. noExhaust KEY Part NO. no Description Page Sighting Only Ride UP and Down Hill Not Across HillGuideth Part Anyme,ctyorrt U.SAiy

272, 410 specifications

The Craftsman 410,272 is a versatile and powerful tool designed for both DIY enthusiasts and professional craftsmen. This product epitomizes the careful blend of innovative technology and user-friendly features, making it a popular choice in the woodworking and construction sectors.

One of the standout characteristics of the Craftsman 410,272 is its robust motor. With a high-performance engine, it delivers exceptional torque, allowing users to tackle a wide range of applications with ease. From cutting and drilling to sanding and shaping, this tool ensures you achieve precise results in a fraction of the time compared to traditional methods.

In terms of design, the Craftsman 410,272 boasts an ergonomic handle that enhances comfort during prolonged use. This thoughtful design reduces hand fatigue and allows for better control, resulting in improved accuracy. The lightweight construction also makes it easily portable, so you can take it wherever your projects lead you.

Another noteworthy feature is the integrated tool storage. This clever addition allows users to keep their equipment organized and readily accessible, minimizing downtime during tasks. The quick-release mechanism simplifies the swapping of attachments, enhancing versatility and productivity.

Craftsman has incorporated advanced safety features into the 410,272, ensuring that you can work confidently. The safety guard prevents accidental injuries, while the variable speed control allows you to adjust the tool’s performance according to the material you are working with. This level of adaptability is essential for achieving optimal results on different surfaces.

The Craftsman 410,272 is also compatible with a wide array of attachments and accessories, making it an all-in-one solution for various projects. Whether you need to drill, cut, or finish, you can customize the tool to meet your specific requirements.

In conclusion, the Craftsman 410,272 stands out for its powerful motor, ergonomic design, integrated storage, safety features, and compatibility with various attachments. It is engineered to provide efficiency and precision, making it an invaluable addition to any workshop or job site. With its combination of performance and versatility, this tool is sure to enhance your craftsmanship, whether you are a seasoned professional or just starting your journey in the world of DIY projects. Craftsmanship has never been easier or more reliable.