Craftsman 917.270751 owner manual Belt Installation, To Adjust Brake, To Replace Motion Drive Belt

Page 23

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instructions.

Mandrel

Idler

Pulleys

Pulley __

/_

 

_',

/_

Mandrel

,_ ,_._L

/ _

_. Pulley

TO ADJUST BRAKE

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.

Depress clutch/brake pedal and engage parking brake.

Measure distance between brake operating arm and nut "A" on brake rod.

If distance is other than 1-1/2", loosen jam nut and turn nut "A" until distance becomes 1-1/2". Retighten jam nut against nut "A".

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest authorized service center/department.

With Parking Brake "Engaged"

Nut "A"

Sam Nut

_ Operating Arm

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a

belt installation guide decal on bottom side of left footrest.

Remove mower (See "TO REMOVE MOWER" in this section of this manual.)

Remove belt from stationary idler and clutching idler.

Pull belt slack toward rear of tractor, Remove belt upwards from transaxle pulley by deflecting belt keepers.

Pull belt toward front of tractor and remove downwards from around engine pulley.

Install new belt by reversing above procedure.

Engine

Pulley

Clutching

Idler

Stationary

Idler

Transaxle

Pulley

TRANSAXLE GEAR SHIFT LEVER ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels

move freely, the transaxle is in neutral.

Loosen adjustment bolt in front of the right rear wheel.

Position the gear shift lever in the neutral (N) position.

Tighten adjustment bolt securely. NOTE: If additional clearance is needed

to get to adjustment bolt, move mower deck height to the lowest position.

23

Image 23
Contents CRI Ftsmrni Limited 90 DAY Warranty on Battery Safety RulesChildren General OperationSlope Operation Do notService Customer Responsibilities Product SpecificationsFl l Before Removing Tractor from Skid Attach Steering Wheel HOW to SET UP Your TractorTools Required for Assembly Check BatteryTo Drive Tractor OFF Skid Install Mulcher PlateCheck for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessJxl ,@ Lever Know Your TractorTo Move Forward and Backward HOW to USE Your Tractor to SET Parking BrakeStopping Throttle ControlTo Operate On Hills To Adjust Mower Cutting To Operate HeightTo Adjust Gauge Wheels AcautionCheck Engine OIL Level Before Starting the EngineADD Gasoline Cold Weather Starting 50 F and below To Start EngineWarm Weather Starting 50 F and Above Mulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Belts Clean AIR INTAKE/COOLING AreasClean AIR Screen EngineSpark Plugs AIR FilterEngine OIL Filter MufflerTo Remove Mower CleaningTo Install Mower Belt Removal To Level Mower HousingTo Replace Motion Drive Belt Belt InstallationTo Adjust Brake Transaxle Gear Shift Lever AdjustmentFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BatteryTo Adjust Steering Wheel Alignment Interlocks and Relays Replacing BatteryTo Remove Hood and Grill Assembly To Replace Headlight BulbTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Cylinders TractorFuel System Engine OILCorrection ProblemCause Correction Troubleshooting ChartProblem CauseOFF Problem CauseOptional Tractor - Model Number SchematicTractor - Model Number 917,270751 Electrical 747604!2 Switch, InterlockTractor - Model Number 111 HAsSlS AHOEHcLOSUEs114 Keeper Belt Rear Lh Stl P930 Tractor --MODEL Number Chassis and Enclosures13 172107X010 Panel, Dash, R.H 30 164918X558 Fend/FtrestTractor - Model Number Ground Drive 113 !27285X Strap Torque 90 Degrees Tractor - Model Number Ground DriveIti Tractor - Model Number 917.270751 Steering Assembly169839 139768154427 169840Tractor - Model Number Engine Engine 134300 140123140551 71110616Wheels & Tires DecalsTractor - Model Number Lift Assembly KEY Part NO. NO.DESCRIPTION 117 Tractor - Model Number Mower DeckTractor - Model Number Mower Deck Numbers Here Part Description 1026 929216 Requiresspecialtools 265Instructionmanual 573 635578 363Fuel Transfer Tube KEY Part NO. no Page Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Days a week Get it fixed, at your home or ours

917.270751 specifications

The Craftsman 917.270751 is a powerful lawn tractor designed for homeowners who demand efficiency and performance in maintaining their lawns. This model seamlessly combines cutting-edge technology, user-friendly features, and durable construction to provide a reliable solution for lawn care.

One of the standout features of the Craftsman 917.270751 is its robust engine. Equipped with a 21.5 HP Briggs & Stratton engine, it offers ample power to tackle various mowing tasks. This engine is designed for smooth operation and durability, ensuring that it can handle large yards and diverse terrain with ease. The automatic transmission further enhances the user experience by allowing smooth speed transitions without the need for manual gear changes.

Another noteworthy characteristic of the Craftsman 917.270751 is its cutting deck. The model features a 42-inch cutting deck, which provides a wide mowing path for efficient grass cutting. This size is ideal for medium to large lawns, allowing users to complete their mowing tasks in less time. The deck is designed for quick height adjustments, accommodating various grass lengths and ensuring a clean, precise cut every time.

The tractor also includes the innovative mulching capability, allowing users to finely chop grass clippings and return them to the lawn, enhancing soil health and reducing waste. This feature not only saves time on yard maintenance but also promotes a healthier lawn ecosystem.

User comfort and convenience are prioritized in the Craftsman 917.270751. The adjustable seat provides ergonomic support during long mowing sessions, while the easy-to-use controls ensure that operators of all skill levels can navigate the tractor effortlessly. Coupled with a tight turning radius, maneuvering around flower beds and tight corners becomes a hassle-free task.

In terms of durability, the Craftsman 917.270751 is built with a heavy-duty steel frame and deck, ensuring it can withstand the challenges of regular use. The tractor comes with a warranty, providing peace of mind for owners regarding its longevity and performance.

In summary, the Craftsman 917.270751 stands out as a well-rounded lawn tractor equipped with features designed for power, efficiency, and user comfort. Its combination of a reliable engine, versatile cutting deck, and innovative technology makes it an excellent choice for homeowners seeking to maintain a pristine lawn with ease.