Craftsman 917.270751 owner manual Install Mulcher Plate, To Drive Tractor OFF Skid

Page 8

Label

Battery Box

Door

al

INSTALL SEAT

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the carboard packing and discard.

•Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely.

•Assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

Seat

Seat Pan

Shoulder _

Bolt _f--_-_'

,-,

,t iN

_Flat Washer

Adjustment

Knob

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and

function of controls)

•Press lift lever plunger and raise

attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID

WARNING: Before starting, read, under- stand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to "OFF" position. Continue with the instructions that follow.

INSTALL MULCHER PLATE

(If previously removed)

•Raise and hold deflector shield in upright position.

•Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

•Hook front latch into hole on front of mower deck.

•Hook rear latch into hole on back of mower deck.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CRI Ftsmrni Safety Rules Limited 90 DAY Warranty on BatteryGeneral Operation Slope OperationDo not ChildrenService Product Specifications Customer ResponsibilitiesFl l HOW to SET UP Your Tractor Tools Required for AssemblyCheck Battery Before Removing Tractor from Skid Attach Steering WheelInstall Mulcher Plate To Drive Tractor OFF SkidTo Convert to Bagging or Discharging Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsJxl ,@ Know Your Tractor LeverHOW to USE Your Tractor to SET Parking Brake StoppingThrottle Control To Move Forward and BackwardTo Adjust Mower Cutting To Operate Height To Adjust Gauge WheelsAcaution To Operate On HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline Cold Weather Starting 50 F and below To Start EngineWarm Weather Starting 50 F and Above Mowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Clean AIR INTAKE/COOLING Areas Clean AIR ScreenEngine BeltsAIR Filter Engine OIL FilterMuffler Spark PlugsTo Remove Mower CleaningTo Install Mower To Level Mower Housing Belt RemovalBelt Installation To Adjust BrakeTransaxle Gear Shift Lever Adjustment To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BatteryTo Adjust Steering Wheel Alignment Replacing Battery To Remove Hood and Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Tractor Fuel SystemEngine OIL CylindersCorrection ProblemCause Troubleshooting Chart ProblemCause CorrectionProblem Cause OFFTractor - Model Number Schematic OptionalTractor - Model Number 917,270751 Electrical 747604!2 Switch, InterlockTractor - Model Number HAsSlS AHOEHcLOSUEs 111Tractor --MODEL Number Chassis and Enclosures 13 172107X010 Panel, Dash, R.H30 164918X558 Fend/Ftrest 114 Keeper Belt Rear Lh Stl P930Tractor - Model Number Ground Drive Tractor - Model Number Ground Drive 113 !27285X Strap Torque 90 DegreesTractor - Model Number 917.270751 Steering Assembly Iti139768 154427169840 169839Tractor - Model Number Engine Engine 140123 14055171110616 134300Decals Wheels & TiresTractor - Model Number Lift Assembly KEY Part NO. NO.DESCRIPTION Tractor - Model Number Mower Deck 117Tractor - Model Number Mower Deck Numbers Here Part Description 929 216Requiresspecialtools 265 1026Instructionmanual 635 578363 573Fuel Transfer Tube KEY Part NO. no Page Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours Days a week

917.270751 specifications

The Craftsman 917.270751 is a powerful lawn tractor designed for homeowners who demand efficiency and performance in maintaining their lawns. This model seamlessly combines cutting-edge technology, user-friendly features, and durable construction to provide a reliable solution for lawn care.

One of the standout features of the Craftsman 917.270751 is its robust engine. Equipped with a 21.5 HP Briggs & Stratton engine, it offers ample power to tackle various mowing tasks. This engine is designed for smooth operation and durability, ensuring that it can handle large yards and diverse terrain with ease. The automatic transmission further enhances the user experience by allowing smooth speed transitions without the need for manual gear changes.

Another noteworthy characteristic of the Craftsman 917.270751 is its cutting deck. The model features a 42-inch cutting deck, which provides a wide mowing path for efficient grass cutting. This size is ideal for medium to large lawns, allowing users to complete their mowing tasks in less time. The deck is designed for quick height adjustments, accommodating various grass lengths and ensuring a clean, precise cut every time.

The tractor also includes the innovative mulching capability, allowing users to finely chop grass clippings and return them to the lawn, enhancing soil health and reducing waste. This feature not only saves time on yard maintenance but also promotes a healthier lawn ecosystem.

User comfort and convenience are prioritized in the Craftsman 917.270751. The adjustable seat provides ergonomic support during long mowing sessions, while the easy-to-use controls ensure that operators of all skill levels can navigate the tractor effortlessly. Coupled with a tight turning radius, maneuvering around flower beds and tight corners becomes a hassle-free task.

In terms of durability, the Craftsman 917.270751 is built with a heavy-duty steel frame and deck, ensuring it can withstand the challenges of regular use. The tractor comes with a warranty, providing peace of mind for owners regarding its longevity and performance.

In summary, the Craftsman 917.270751 stands out as a well-rounded lawn tractor equipped with features designed for power, efficiency, and user comfort. Its combination of a reliable engine, versatile cutting deck, and innovative technology makes it an excellent choice for homeowners seeking to maintain a pristine lawn with ease.
Top Page Image Contents