Craftsman 917.2759 To Operate Mower, To Adjust Gauge Wheels, Using the Reverse Operation System

Page 12

,The average lawn should be cut to ap- proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

,For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted

when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Be sure tractor is on a flat level surface.

1.Lower mower and adjust mower to desired cutting height.

2.Remove retainer spring and clevis pin which secure each gauge wheel bar.

3.Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

4.Replace retainer spring into clevis pin.

5.Be sure all gauge wheels are in the same setting.

IMPORTANT." Be sure to readjust gauge

wheels if you change the cutting height of the mower deck.

Retainer Spring

Clevis Pin

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1.Select desired height of cut.

2.Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

_CAUTION: Do not operate the mower with- out either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

Push In To "Disengage"Attachment Lift Lever

High

Position

 

 

Low

 

 

Position

Attachment

_-

 

Clutch Switch

 

Deflector

Pull Out To

_

Shield

"Engage"

 

 

REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direc- tion with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

_.WARNING: Backing up with the at- tachment clutch engaged while mowing

is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in

reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

1.Move motion control lever to neutral

(N)position.

2.With engine running, turn ignition key

counterclockwise to ROS "ON" posi- tion.

3.Look down and behind before backing.

4.Slowly move motion control lever to reverse (R) position to start movement.

5.When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" Position Engine "ON" Position (Normal Operating)

12

Image 12
Contents Crrftsmrh Limited Warrantyon Craftsmanriding Equipment Limited Warranty on BatteryGeneral Operation Service Safe Handling of Gasoline II. Slope OperationIV. Towing General Service Sears Installation Service Repair ProtectionFor prices and additional information call 1=800=827=6655 Check Battery Adjust SeatTo Remove Tractor from Carton Unpack CartonChecklist Check Deck LevelnessALL Belts Check Brake System@@@@ Will result in death or serious injuryKnow Your Tractor HOW to USE Your Tractor StoppingParking MoveTo Adjust Gauge Wheels Using the Reverse Operation SystemTo Operate Mower To Transport To Operate on HillsTransmission Disengaged Towing Carts and Other ATTACH- MentsTo Start Engine Automatic Transmission Warm UPMowing Tips Asyoucomplete General RecommendationsCheck Operator Presence System To Change Engine OIL Engine LubricationTo Service PRE-CLEANER To Service CartridgeClean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning MufflerSpark Plugs IN-LINE Fuel FilterVice or Adjustments TractorRemove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Replace Mower Drive Belt Both Front Plate Links Must be Equal in LengthMower Drive Belt Removal Install NEW Mower Blade Secondary Drive Belt Reinstall Mower Drive BeltTo Replace Mower Blade Secondary Drive Belt Remove Mower Drive BeltWith parking Replacing Battery To Start Engine with a Weak BAT- TeryTo Attach Jumper Cables To Adjust Throttle Control Cable To Replace Headlight BulbTo Replace Fuse To Remove Hood and Grill AS- SemblyPreliminary Setting To Adjust Choke ControlTo Adjust Carburetor Final SettingFuel System Engine OILCylinders OtherProblem Loss PowerWill not Clicks butProblem Cause VibrationEngine dies whet tractor is shifted Operator leaves seat with Attach merit Clutch engagedProblemcause DischargeWorking Loss of driveSchematic Tractor = = Model NumberTractor = = Model Number Electrical Electrical KEY Part DESCRiPTiONTractor = = Model Number 917.275900 Chassis and Enclosures Tractor = = Model Number 917.275900 Chassis and Enclosures KEY PartGround Drive Tractor . . Model Number Tractor - Model Number Ground Drive PartDescription Tractor = = Model Number Description Tractor - Model Number Tractor = = Model Number Seat Assembly Decals KEY PartLiFT Assembly Tractor - Model NumberMower Deck Number 111111 Tractor = = Model Cylinder Head Valve and Breather ENGINE=MODEL HEAD/VALVE/BR Eath ERCrankcase KEY ITO AiR INTAKE/FILTRATION Kohler ENGINE=MODEL Number CV730, Type Number Tractor -- Model Number OiL PAN/LUBRICATIONKohler ENGINE=MODEL Number CV730, Type Number Exhaust KEY Part Fuel SystemPage Only Ride UP and Down Hill Not Across HillDegrees MAX Iiiiiii!iii ,YourHome....iHiiiilHiiiHiHi 800LE.FOYERMC

917.2759 specifications

The Craftsman 917.2759 is a powerful lawn tractor designed for homeowners seeking efficiency and reliability in maintaining their lawns. This robust riding mower features a 42-inch cutting deck, which allows for a wide cutting path, ensuring that mowing tasks are completed swiftly. With a 19.5 horsepower Briggs & Stratton engine, the Craftsman 917.2759 delivers adequate power for various mowing conditions, from flat terrains to slightly hilly landscapes.

One of the key features of this tractor is its automatic transmission, which allows for smooth and effortless speed adjustments. Users can easily transition between forward and reverse without the hassle of shifting gears manually. This makes maneuvering around trees, flower beds, and other obstacles much simpler. The tractor also boasts a comfortable high-back seat, providing ample support during long mowing sessions.

Technologically advanced, the Craftsman 917.2759 includes a debris management system that prevents grass clippings from clogging the cutting deck. With its side discharge feature, the mower efficiently expels clippings to the side, promoting a cleaner mowing experience. For those who prefer to collect clippings, optional bagging systems are available, further enhancing the mower's versatility.

In terms of durability, the Craftsman 917.2759 is built with a heavy-duty steel frame and a reinforced cutting deck, ensuring it can withstand the wear and tear of regular use. The tire design offers excellent traction on various terrains, contributing to seamless movement across the lawn.

Another noteworthy characteristic of this tractor is its ease of maintenance. The placement of the engine and battery allows for straightforward access, making it convenient for users to perform routine checks. Additionally, the mower supports various attachments, making it adaptable for different gardening tasks, such as leaf collection, snow removal, and aeration.

Overall, the Craftsman 917.2759 is an excellent choice for homeowners looking for a reliable, feature-rich lawn tractor that can tackle various mowing tasks effectively. Its combination of power, comfort, and innovative technologies positions it as a valuable tool for maintaining a beautiful and healthy lawn.