Craftsman 917.2759 manual To Replace Headlight Bulb, To Replace Fuse, Engine

Page 27

3. Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

Hex Bolt

Positive (Red)

Cable

Negative (Black)

Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

iNTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to reconnect the headlight wire connector.

Hood

Headlight Wire

Connector

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road

engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever to fast position.

2.Check that speed control lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw. Tighten clamp screw securely.

Idle Fuel Adjusting

Idle Speed

Needle (If Equipped)

, Adjusting Screw

Control

Cable

Choke

Control

Cable

Clamp Screw

27

Image 27
Contents Crrftsmrh Limited Warranty on Battery Limited Warrantyon Craftsmanriding EquipmentGeneral Operation Service Safe Handling of Gasoline II. Slope OperationIV. Towing General Service Sears Installation Service Repair ProtectionFor prices and additional information call 1=800=827=6655 Unpack Carton Check BatteryAdjust Seat To Remove Tractor from CartonCheck Brake System ChecklistCheck Deck Levelness ALL BeltsWill result in death or serious injury @@@@Know Your Tractor Move HOW to USE Your TractorStopping ParkingTo Adjust Gauge Wheels Using the Reverse Operation SystemTo Operate Mower Towing Carts and Other ATTACH- Ments To TransportTo Operate on Hills Transmission DisengagedAutomatic Transmission Warm UP To Start EngineMowing Tips General Recommendations AsyoucompleteCheck Operator Presence System Engine Lubrication To Change Engine OILClean AIR INTAKE/COOLING Areas To Service PRE-CLEANERTo Service Cartridge Clean AIR ScreenIN-LINE Fuel Filter CleaningMuffler Spark PlugsVice or Adjustments TractorRemove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Replace Mower Drive Belt Both Front Plate Links Must be Equal in LengthMower Drive Belt Removal Remove Mower Drive Belt Install NEW Mower Blade Secondary Drive BeltReinstall Mower Drive Belt To Replace Mower Blade Secondary Drive BeltWith parking Replacing Battery To Start Engine with a Weak BAT- TeryTo Attach Jumper Cables To Remove Hood and Grill AS- Sembly To Adjust Throttle Control CableTo Replace Headlight Bulb To Replace FuseFinal Setting Preliminary SettingTo Adjust Choke Control To Adjust CarburetorOther Fuel SystemEngine OIL CylindersClicks but ProblemLoss Power Will notOperator leaves seat with Attach merit Clutch engaged Problem CauseVibration Engine dies whet tractor is shiftedLoss of drive ProblemcauseDischarge WorkingTractor = = Model Number SchematicTractor = = Model Number Electrical DESCRiPTiON Electrical KEY PartTractor = = Model Number 917.275900 Chassis and Enclosures KEY Part Tractor = = Model Number 917.275900 Chassis and EnclosuresGround Drive Tractor . . Model Number Tractor - Model Number Ground Drive PartDescription Tractor = = Model Number Description Tractor - Model Number Tractor = = Model Number Seat Assembly KEY Part DecalsTractor - Model Number LiFT AssemblyMower Deck Number 111111 Tractor = = Model Cylinder Head Valve and Breather ENGINE=MODEL HEAD/VALVE/BR Eath ERCrankcase KEY ITO AiR INTAKE/FILTRATION Kohler ENGINE=MODEL Number CV730, Type Number OiL PAN/LUBRICATION Tractor -- Model NumberKohler ENGINE=MODEL Number CV730, Type Number Fuel System Exhaust KEY PartPage Only Ride UP and Down Hill Not Across HillDegrees MAX 800LE.FOYERMC Iiiiiii!iii ,YourHome....iHiiiilHiiiHiHi

917.2759 specifications

The Craftsman 917.2759 is a powerful lawn tractor designed for homeowners seeking efficiency and reliability in maintaining their lawns. This robust riding mower features a 42-inch cutting deck, which allows for a wide cutting path, ensuring that mowing tasks are completed swiftly. With a 19.5 horsepower Briggs & Stratton engine, the Craftsman 917.2759 delivers adequate power for various mowing conditions, from flat terrains to slightly hilly landscapes.

One of the key features of this tractor is its automatic transmission, which allows for smooth and effortless speed adjustments. Users can easily transition between forward and reverse without the hassle of shifting gears manually. This makes maneuvering around trees, flower beds, and other obstacles much simpler. The tractor also boasts a comfortable high-back seat, providing ample support during long mowing sessions.

Technologically advanced, the Craftsman 917.2759 includes a debris management system that prevents grass clippings from clogging the cutting deck. With its side discharge feature, the mower efficiently expels clippings to the side, promoting a cleaner mowing experience. For those who prefer to collect clippings, optional bagging systems are available, further enhancing the mower's versatility.

In terms of durability, the Craftsman 917.2759 is built with a heavy-duty steel frame and a reinforced cutting deck, ensuring it can withstand the wear and tear of regular use. The tire design offers excellent traction on various terrains, contributing to seamless movement across the lawn.

Another noteworthy characteristic of this tractor is its ease of maintenance. The placement of the engine and battery allows for straightforward access, making it convenient for users to perform routine checks. Additionally, the mower supports various attachments, making it adaptable for different gardening tasks, such as leaf collection, snow removal, and aeration.

Overall, the Craftsman 917.2759 is an excellent choice for homeowners looking for a reliable, feature-rich lawn tractor that can tackle various mowing tasks effectively. Its combination of power, comfort, and innovative technologies positions it as a valuable tool for maintaining a beautiful and healthy lawn.