Craftsman 917.2759 manual To Start Engine with a Weak BAT- Tery, To Attach Jumper Cables

Page 26

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal

for service or replacement, it should be

purged after reinstallation and before op- erating the tractor. See "PURGE TRANS- MISSION" in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars

horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in

or camber, contact your nearest Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align

grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion.

Retaining

Ring \ Washers

Axle \

Cover \

I

Square Key _

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT- TERY

_,WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the Maintenance section of this

manual).

If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable

to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK

cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

02614

Weak or Dead Fully Charged

BatteryBattery

REPLACING BATTERY

_IkWARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Crrftsmrh Limited Warrantyon Craftsmanriding Equipment Limited Warranty on BatteryGeneral Operation IV. Towing Service Safe Handling of GasolineII. Slope Operation General Service For prices and additional information call 1=800=827=6655 Sears Installation ServiceRepair Protection To Remove Tractor from Carton Check BatteryAdjust Seat Unpack CartonALL Belts ChecklistCheck Deck Levelness Check Brake System@@@@ Will result in death or serious injuryKnow Your Tractor Parking HOW to USE Your TractorStopping MoveTo Operate Mower To Adjust Gauge WheelsUsing the Reverse Operation System Transmission Disengaged To TransportTo Operate on Hills Towing Carts and Other ATTACH- MentsTo Start Engine Automatic Transmission Warm UPMowing Tips Asyoucomplete General RecommendationsCheck Operator Presence System To Change Engine OIL Engine LubricationClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Clean AIR INTAKE/COOLING AreasSpark Plugs CleaningMuffler IN-LINE Fuel FilterRemove Mower Vice or AdjustmentsTractor FRONT-TO-BACK Adjustment To Level Mower HousingSIDE-TO-SIDE Adjustment Mower Drive Belt Removal To Replace Mower Drive BeltBoth Front Plate Links Must be Equal in Length To Replace Mower Blade Secondary Drive Belt Install NEW Mower Blade Secondary Drive BeltReinstall Mower Drive Belt Remove Mower Drive BeltWith parking To Attach Jumper Cables Replacing BatteryTo Start Engine with a Weak BAT- Tery To Replace Fuse To Adjust Throttle Control CableTo Replace Headlight Bulb To Remove Hood and Grill AS- SemblyTo Adjust Carburetor Preliminary SettingTo Adjust Choke Control Final SettingCylinders Fuel SystemEngine OIL OtherWill not ProblemLoss Power Clicks butEngine dies whet tractor is shifted Problem CauseVibration Operator leaves seat with Attach merit Clutch engagedWorking ProblemcauseDischarge Loss of driveSchematic Tractor = = Model NumberTractor = = Model Number Electrical Electrical KEY Part DESCRiPTiONTractor = = Model Number 917.275900 Chassis and Enclosures Tractor = = Model Number 917.275900 Chassis and Enclosures KEY PartGround Drive Tractor . . Model Number Description Tractor - Model Number Ground DrivePart Tractor = = Model Number Description Tractor - Model Number Tractor = = Model Number Seat Assembly Decals KEY PartLiFT Assembly Tractor - Model NumberMower Deck Number 111111 Tractor = = Model Cylinder Head Valve and Breather Crankcase KEY ENGINE=MODELHEAD/VALVE/BR Eath ER ITO AiR INTAKE/FILTRATION Kohler ENGINE=MODEL Number CV730, Type Number Tractor -- Model Number OiL PAN/LUBRICATIONKohler ENGINE=MODEL Number CV730, Type Number Exhaust KEY Part Fuel SystemPage Degrees MAX Only Ride UP and Down HillNot Across Hill Iiiiiii!iii ,YourHome....iHiiiilHiiiHiHi 800LE.FOYERMC

917.2759 specifications

The Craftsman 917.2759 is a powerful lawn tractor designed for homeowners seeking efficiency and reliability in maintaining their lawns. This robust riding mower features a 42-inch cutting deck, which allows for a wide cutting path, ensuring that mowing tasks are completed swiftly. With a 19.5 horsepower Briggs & Stratton engine, the Craftsman 917.2759 delivers adequate power for various mowing conditions, from flat terrains to slightly hilly landscapes.

One of the key features of this tractor is its automatic transmission, which allows for smooth and effortless speed adjustments. Users can easily transition between forward and reverse without the hassle of shifting gears manually. This makes maneuvering around trees, flower beds, and other obstacles much simpler. The tractor also boasts a comfortable high-back seat, providing ample support during long mowing sessions.

Technologically advanced, the Craftsman 917.2759 includes a debris management system that prevents grass clippings from clogging the cutting deck. With its side discharge feature, the mower efficiently expels clippings to the side, promoting a cleaner mowing experience. For those who prefer to collect clippings, optional bagging systems are available, further enhancing the mower's versatility.

In terms of durability, the Craftsman 917.2759 is built with a heavy-duty steel frame and a reinforced cutting deck, ensuring it can withstand the wear and tear of regular use. The tire design offers excellent traction on various terrains, contributing to seamless movement across the lawn.

Another noteworthy characteristic of this tractor is its ease of maintenance. The placement of the engine and battery allows for straightforward access, making it convenient for users to perform routine checks. Additionally, the mower supports various attachments, making it adaptable for different gardening tasks, such as leaf collection, snow removal, and aeration.

Overall, the Craftsman 917.2759 is an excellent choice for homeowners looking for a reliable, feature-rich lawn tractor that can tackle various mowing tasks effectively. Its combination of power, comfort, and innovative technologies positions it as a valuable tool for maintaining a beautiful and healthy lawn.
Top Page Image Contents