Craftsman 917.27624 owner manual To Remove Mower, To Install Mower, To Level Mower Housing

Page 23

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER- VICE OR ADJUSTMENTS:

1.Depress brake pedal fully and set parking brake.

2.Place attachment clutch in "DISENGAGED" position.

3.Turn ignition key to "STOP" and remove key.

4.Make sure the blades and all moving parts have completely stopped.

5.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER

1.Place attachment clutch in "DISEN- GAGED" position.

2.Lower attachment lift lever to its lowest position.

3.Disengage belt tension rod from lock bracket.

_, CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and re- lease slowly.

4.Remove mower belt from electric clutch pulley.

5.DISCONNECT REAR MOWER PINS FIRST - Pull out the spring loaded pin, disconnect suspension arm from pin and release pin.

6.Go to other side of mower and discon- nect rear pin in the same manner.

7.Remove the four retainer springs and two flanged pins from front plate as-

sembly and remove plate.

8.Raise attachment lift lever to its highest position.

Belt Tension Rod

Bracket

Disengage_on

9.Turn tractor steering wheel to the left as far as it will go.

10.Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in "INSTALL MOWER AND DRIVE BELT" in the As-

sembly section of this manual. NOTE: You will need to reattach front plate assembly

to tractor after sliding mower under the tractor.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•Measure height from bottom edge of

mower to ground level at front corners

of mower. Distance "A" on both sides of mower should be the same.

Electric Clutch Pulley

!

Front Plate Assembly

 

 

Double

Loop

 

Retainer

Springs

,,p-------Single Loop

Retainer Springs

Flanged Pins

Rear Mower Pins

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Crrftsmiin Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Safe Handling of Gasoline ServiceIII. Children IV. TowingGeneral Service Repair Protection Agreements ProductSteering Wheel To Remove Tractor from Carton To Drive Tractor OFF Skid See Operation section for location Attach Front Plate Connect Rear PinsInstall Mower and Drive Belt Assemble Gauge Wheels to Mower DeckCheck Brake System ChecklistCheck Mower Levelness Automatic Models only ROS on Know Your TractorTractor To Move Forward and Backward HOW to USE Your TractorTo SET Parking Brake StoppingTo Stop Mower Blades Using the Reverse Operation SystemTo Operate Mower Before Starting the Engine Check Engine OIL Level To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsAutomatic Transmission Warm UP To Start EngineMowing Tips Purge TransmissionTransport General Recommendations Lubrication ChartBefore Each USE To Sharpen Blade Blade RemovalBelts BatteryEngine Transaxle CoolingMuffler Clean AIR ScreenCleaning Engine OIL FilterTo Remove Mower To Install MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Drive Belt FRONT-TO-BACK AdjustmentMower Drive Belt Installation Both Front Plate Links Must be Equal in LengthTo Check Brake To Adjust Attachment ClutchTo Check and Adjust Brake To Adjust BrakeTo Remove Wheel for Repairs To Adjust Steering Wheel Align MentTo Replace Motion Drive Belt To Start Engine with a Weak BATReplacing Battery Final Setting To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingOther Engine OILCylinders Start Troubleshooting ChartCorrection Problem CauseROS Not rotate Problem Cause CorrectionTractor --MODEL Number SchematicTractor --MODEL Number Electrical KEY Part Description ElectricalTractor --MODEL Number Chassis and Enclosures 148 164655 Extrusion Bumpers 179716X428 Tractor --MODEL Number Ground Drive LH VGT Steering KEY Part NO. NO.DESCRIPTION Engine Spark Arrester KIT J NO. NO. Description Tractor --MODEL Number Seat AssemblyKEY Part KEY PartDecals Wheels and TiresLift Assembly Tractor --MODEL Number Mower Deck KEY Part NO. NO.DESCRIPTION Tractor --MODEL Number TRANSAXLE--MODEL Number Bushing .50X .60X Ylinder HEAD, Valve and Breatherj KEY Part NO. no HEAD/VALVE/BREATHERDescription Crankcase KEY Part NO. noIGNITION/ELECTRICALJ Blower Housing and Baffles Notillustrated 24-096-85-S Blower Housing KEY Part NO. noAIR INTAKE/FILTRATION IGNITION/ELECTRICAL KEY Part DescriptionStarting System J Engine Controls J OIL PAN / Lubrication OIL PAN/LUBRICATION KEY Part Description DescriptionStarting System Crankshaft Exhaust J Fuel SystemjCrankshaft KEY Part Description Fuel SystemPage Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationIiiiiiiiiiiiiiiii

917.27624 specifications

The Craftsman 917.27624 is a robust lawn tractor designed for homeowners seeking efficiency, performance, and reliability in their lawn care routine. With a powerful engine and innovative features, this model stands out among its peers in the gardening equipment market.

At the heart of the Craftsman 917.27624 is a 19 horsepower Briggs & Stratton engine, which provides ample power for various lawn care tasks. The engine's reliable performance ensures that users can tackle tough grass conditions and maintain their lawns without interruption. Coupled with a 42-inch cutting deck, this lawn tractor is capable of delivering a precise and clean cut, making it ideal for medium to large-sized yards.

One standout feature of the Craftsman 917.27624 is its advanced transmission system. It comes equipped with a hydrostatic transmission, allowing for smooth acceleration and effortless operation. This system eliminates the hassle of shifting gears, enabling users to focus on mowing without distractions. The adjustable cutting height, offering six different settings, adds versatility to the mowing experience, allowing users to customize their cut according to their lawn's needs.

In terms of comfort, the Craftsman 917.27624 does not fall short. It features a plush, adjustable high-back seat designed to provide maximum support during longer mowing sessions. The steering wheel is ergonomically designed, allowing for responsive handling and maneuverability, making it easier to navigate around tight spaces and landscaping features.

The Craftsman 917.27624 is also equipped with innovative safety features, including an automatic shut-off mechanism that activates when the operator leaves the seat. This feature enhances safety while operating the equipment and prevents accidents caused by unintended movement.

Additionally, this model includes a debris shield and optimized airflow technology that enhances grass collection efficiency. These features ensure that clippings are neatly collected, helping keep the lawn appearance tidy and preventing the buildup of organic matter that can harm grass health.

Overall, the Craftsman 917.27624 is an excellent choice for homeowners who require a reliable lawn tractor with power, comfort, and advanced features for efficient lawn maintenance. Whether mowing, mulching, or towing attachments, this lawn tractor delivers outstanding performance suited to meet diverse lawn care needs.
Top Page Image Contents