Craftsman 917.27624 owner manual To Remove Tractor from Carton

Page 8

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need

are

listed

below.

 

 

(1)

9/16"

wrench

(1)

Pliers

(1)

1/2"

wrench

(1)

Utility knife

(1)3/4" socket with drive ratchet

(1) Tire pressure gauge

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

3.Remove mower and packing materials.

4.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR

FROM SKID

ATTACH STEERING WHEEL

1.Remove Iocknut and large flat washer from steering shaft.

2.Position front wheels of the tractor so they are pointing straight forward.

3.Slide the steering sleeve over the steering shaft.

4.Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

5.Secure steering wheel to steering

shaft with Iocknut and large flat washer previously removed. Tighten securely.

6.Snap steering wheel insert into center of steering wheel.

7.Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off skid.

Insert

Lock Nut

__teering Wheel Large Flat

Washer

Steering

Wheel-

-- AdaptorSteering Wheel

Steering

Shaft

Steering

Sleeve

CHECK BATTERY

1. Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc- tions).

,, --., _Label

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Crrftsmiin Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation Service III. ChildrenIV. Towing Safe Handling of GasolineGeneral Service Product Repair Protection AgreementsSteering Wheel To Remove Tractor from Carton To Drive Tractor OFF Skid See Operation section for location Connect Rear Pins Install Mower and Drive BeltAssemble Gauge Wheels to Mower Deck Attach Front PlateCheck Brake System ChecklistCheck Mower Levelness Automatic Models only ROS on Know Your TractorTractor HOW to USE Your Tractor To SET Parking BrakeStopping To Move Forward and BackwardTo Stop Mower Blades Using the Reverse Operation SystemTo Operate Mower To Operate on Hills To TransportTowing Carts and Other ATTACH- Ments Before Starting the Engine Check Engine OIL LevelTo Start Engine Automatic Transmission Warm UPMowing Tips Purge TransmissionTransport General Recommendations Lubrication ChartBefore Each USE Blade Removal To Sharpen BladeBattery EngineTransaxle Cooling BeltsClean AIR Screen CleaningEngine OIL Filter MufflerTo Install Mower To Level Mower HousingSIDE-TO-SIDE Adjustment To Remove MowerFRONT-TO-BACK Adjustment Mower Drive Belt InstallationBoth Front Plate Links Must be Equal in Length To Replace Mower Drive BeltTo Adjust Attachment Clutch To Check and Adjust BrakeTo Adjust Brake To Check BrakeTo Adjust Steering Wheel Align Ment To Replace Motion Drive BeltTo Start Engine with a Weak BAT To Remove Wheel for RepairsReplacing Battery To Adjust Choke Control To Adjust CarburetorPreliminary Setting Final SettingOther Engine OILCylinders Troubleshooting Chart StartCorrection Problem CauseROS Problem Cause Correction Not rotateSchematic Tractor --MODEL NumberTractor --MODEL Number Electrical Electrical KEY Part DescriptionTractor --MODEL Number Chassis and Enclosures 148 164655 Extrusion Bumpers 179716X428 Tractor --MODEL Number Ground Drive LH VGT Steering KEY Part NO. NO.DESCRIPTION Engine Spark Arrester KIT J Tractor --MODEL Number Seat Assembly KEY PartKEY Part NO. NO. DescriptionWheels and Tires DecalsLift Assembly Tractor --MODEL Number Mower Deck KEY Part NO. NO.DESCRIPTION Tractor --MODEL Number TRANSAXLE--MODEL Number Bushing .50X .60X Ylinder HEAD, Valve and Breatherj HEAD/VALVE/BREATHER DescriptionCrankcase KEY Part NO. no KEY Part NO. noIGNITION/ELECTRICALJ Blower Housing and Baffles Blower Housing KEY Part NO. no AIR INTAKE/FILTRATIONIGNITION/ELECTRICAL KEY Part Description Notillustrated 24-096-85-SStarting System J Engine Controls J OIL PAN / Lubrication OIL PAN/LUBRICATION KEY Part Description DescriptionStarting System Fuel Systemj Crankshaft Exhaust JFuel System Crankshaft KEY Part DescriptionPage Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXIiiiiiiiiiiiiiiii

917.27624 specifications

The Craftsman 917.27624 is a robust lawn tractor designed for homeowners seeking efficiency, performance, and reliability in their lawn care routine. With a powerful engine and innovative features, this model stands out among its peers in the gardening equipment market.

At the heart of the Craftsman 917.27624 is a 19 horsepower Briggs & Stratton engine, which provides ample power for various lawn care tasks. The engine's reliable performance ensures that users can tackle tough grass conditions and maintain their lawns without interruption. Coupled with a 42-inch cutting deck, this lawn tractor is capable of delivering a precise and clean cut, making it ideal for medium to large-sized yards.

One standout feature of the Craftsman 917.27624 is its advanced transmission system. It comes equipped with a hydrostatic transmission, allowing for smooth acceleration and effortless operation. This system eliminates the hassle of shifting gears, enabling users to focus on mowing without distractions. The adjustable cutting height, offering six different settings, adds versatility to the mowing experience, allowing users to customize their cut according to their lawn's needs.

In terms of comfort, the Craftsman 917.27624 does not fall short. It features a plush, adjustable high-back seat designed to provide maximum support during longer mowing sessions. The steering wheel is ergonomically designed, allowing for responsive handling and maneuverability, making it easier to navigate around tight spaces and landscaping features.

The Craftsman 917.27624 is also equipped with innovative safety features, including an automatic shut-off mechanism that activates when the operator leaves the seat. This feature enhances safety while operating the equipment and prevents accidents caused by unintended movement.

Additionally, this model includes a debris shield and optimized airflow technology that enhances grass collection efficiency. These features ensure that clippings are neatly collected, helping keep the lawn appearance tidy and preventing the buildup of organic matter that can harm grass health.

Overall, the Craftsman 917.27624 is an excellent choice for homeowners who require a reliable lawn tractor with power, comfort, and advanced features for efficient lawn maintenance. Whether mowing, mulching, or towing attachments, this lawn tractor delivers outstanding performance suited to meet diverse lawn care needs.
Top Page Image Contents