Craftsman 917.27624 owner manual Replacing Battery

Page 27

DD

02614

Weak or Dead Fully Charged

BatteryBattery

REPLACING BATTERY

,_WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,

rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to negative (-) battery terminal with re-

maining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

 

Keps

 

Terminal

.--'

Hex

Access

,,

Bolt

Door

 

Positive

 

 

(Red) Cable

Guard

 

,gative (Black)

 

 

Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in

the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

.Hood

Headlight Wire

Connector

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road

engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever to fast position.

2.Check that speed control lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw. Tighten clamp screw securely.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Crrftsmiin Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Safe Handling of Gasoline ServiceIII. Children IV. TowingGeneral Service Repair Protection Agreements ProductSteering Wheel To Remove Tractor from Carton To Drive Tractor OFF Skid See Operation section for location Attach Front Plate Connect Rear PinsInstall Mower and Drive Belt Assemble Gauge Wheels to Mower DeckChecklist Check Mower LevelnessCheck Brake System Automatic Models only Know Your Tractor TractorROS on To Move Forward and Backward HOW to USE Your TractorTo SET Parking Brake StoppingUsing the Reverse Operation System To Operate MowerTo Stop Mower Blades Before Starting the Engine Check Engine OIL Level To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsAutomatic Transmission Warm UP To Start EnginePurge Transmission TransportMowing Tips Lubrication Chart Before Each USEGeneral Recommendations To Sharpen Blade Blade RemovalBelts BatteryEngine Transaxle CoolingMuffler Clean AIR ScreenCleaning Engine OIL FilterTo Remove Mower To Install MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Drive Belt FRONT-TO-BACK AdjustmentMower Drive Belt Installation Both Front Plate Links Must be Equal in LengthTo Check Brake To Adjust Attachment ClutchTo Check and Adjust Brake To Adjust BrakeTo Remove Wheel for Repairs To Adjust Steering Wheel Align MentTo Replace Motion Drive Belt To Start Engine with a Weak BATReplacing Battery Final Setting To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingEngine OIL CylindersOther Start Troubleshooting ChartProblem Cause ROSCorrection Not rotate Problem Cause CorrectionTractor --MODEL Number SchematicTractor --MODEL Number Electrical KEY Part Description ElectricalTractor --MODEL Number Chassis and Enclosures 148 164655 Extrusion Bumpers 179716X428 Tractor --MODEL Number Ground Drive LH VGT Steering KEY Part NO. NO.DESCRIPTION Engine Spark Arrester KIT J NO. NO. Description Tractor --MODEL Number Seat AssemblyKEY Part KEY PartDecals Wheels and TiresLift Assembly Tractor --MODEL Number Mower Deck KEY Part NO. NO.DESCRIPTION Tractor --MODEL Number TRANSAXLE--MODEL Number Bushing .50X .60X Ylinder HEAD, Valve and Breatherj KEY Part NO. no HEAD/VALVE/BREATHERDescription Crankcase KEY Part NO. noIGNITION/ELECTRICALJ Blower Housing and Baffles Notillustrated 24-096-85-S Blower Housing KEY Part NO. noAIR INTAKE/FILTRATION IGNITION/ELECTRICAL KEY Part DescriptionStarting System J Engine Controls J OIL PAN / Lubrication Description Starting SystemOIL PAN/LUBRICATION KEY Part Description Crankshaft Exhaust J Fuel SystemjCrankshaft KEY Part Description Fuel SystemPage Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationIiiiiiiiiiiiiiiii

917.27624 specifications

The Craftsman 917.27624 is a robust lawn tractor designed for homeowners seeking efficiency, performance, and reliability in their lawn care routine. With a powerful engine and innovative features, this model stands out among its peers in the gardening equipment market.

At the heart of the Craftsman 917.27624 is a 19 horsepower Briggs & Stratton engine, which provides ample power for various lawn care tasks. The engine's reliable performance ensures that users can tackle tough grass conditions and maintain their lawns without interruption. Coupled with a 42-inch cutting deck, this lawn tractor is capable of delivering a precise and clean cut, making it ideal for medium to large-sized yards.

One standout feature of the Craftsman 917.27624 is its advanced transmission system. It comes equipped with a hydrostatic transmission, allowing for smooth acceleration and effortless operation. This system eliminates the hassle of shifting gears, enabling users to focus on mowing without distractions. The adjustable cutting height, offering six different settings, adds versatility to the mowing experience, allowing users to customize their cut according to their lawn's needs.

In terms of comfort, the Craftsman 917.27624 does not fall short. It features a plush, adjustable high-back seat designed to provide maximum support during longer mowing sessions. The steering wheel is ergonomically designed, allowing for responsive handling and maneuverability, making it easier to navigate around tight spaces and landscaping features.

The Craftsman 917.27624 is also equipped with innovative safety features, including an automatic shut-off mechanism that activates when the operator leaves the seat. This feature enhances safety while operating the equipment and prevents accidents caused by unintended movement.

Additionally, this model includes a debris shield and optimized airflow technology that enhances grass collection efficiency. These features ensure that clippings are neatly collected, helping keep the lawn appearance tidy and preventing the buildup of organic matter that can harm grass health.

Overall, the Craftsman 917.27624 is an excellent choice for homeowners who require a reliable lawn tractor with power, comfort, and advanced features for efficient lawn maintenance. Whether mowing, mulching, or towing attachments, this lawn tractor delivers outstanding performance suited to meet diverse lawn care needs.
Top Page Image Contents