Craftsman 917.27528 To Adjust Gauge Wheels, To Operate Mower, To Operate On Hills Iicaution

Page 12

The cutting height range is approximately 1-1/2" to 4-1/2". The heights are mea- sured from the ground to the blade tip with the engine not running.

These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to

approximately 2-1/2 inches during the cool season and to over 3 inches

during hot months. For healthier and

better looking lawns, mow often and

 

after moderate growth.

;'

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut

relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Be sure tractor is on a flat level surface.

1.Lower mower and adjust mower to desired cutting height.

2.Remove retainer spring and clevis pin which secure each gauge wheel bar.

3.Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels

should be slightly off the ground.

4.Replace retainer spring into clevis pin.

5.Be sure all gauge wheels are in the same setting.

IMPORTANT: Be sure to readjust gauge

wheels if you change the cutting height of the mower deck.

Retainer F ---'-'-//._"/" "" __---

Spring _1__i_

is"ll_ ' 'i" "

Pin

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

1.Select desired height of cut.

2.Lower mower with attachment lift control.

3.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

,_CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

Attachemnt Lift

Attachment Clutch Lever High Position

Switch Pull Out to

"Engage"

to

"Disengage"

 

 

Deflector

 

Shield

TO OPERATE

ON HILLS

IICAUTION:

Do not drive up or down

hills with

slopes

greater than 15 °

and do

not drive

across

any

slope.

Use the slope

guide provided

at the

back

of this

manual.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake

position and engage parking brake. IMPORTANT: The motion control lever

returns to neutral (N) position when the brake pedal is depressed.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Jcraftsmanj Sears Craftsman Help LineService RepairSears Back CoverSafety General OperationII. Slope Operation YourIV. Service Mow up and down slopes, not acrossDo not IlL ChildrenRemove obstacles such as rocks, tree limbs, etc Product Specifications API-SF-SJRepair Agreement Customer ResponsibilitiesCheck Battery Install SeatTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position ALL Belts Check Brake SystemH L Knowyour Tractor Your Tractor Motion Drive Belt TensionHOW to USE Your Tractor To Adjust Gauge Wheels To Operate MowerTo Operate On Hills Iicaution Before Starting the Engine Purgetransmssion Automatic Transmission Warm UPMowing Tips Lubrication Chart General RecommendationsBefore Each USE Battery TiresOperator Presence System Blade CareTransaxle Cooling Transaxle Pump FluidBelts Engine LubricationTo Service Cartridge Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower To Level Mower Housing Bubble Between Lines m/b Bubble LevelBrake .. Left Hand Footrest Lift Link ANdustment Both Front Links Must be Equal LengthTo Replace Mower Drive Belt Electric PulleyArm To Replace Mower Blade SEC- Ondary Drive BeltTo Adjust Attachment Clutch To Adjust BrakeTo Replace Motion Drive Belt Belt Installation Transaxle Motion Control Lever Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN AdjustmentFront Wheel Camber To Remove Wheel for RepairsTo Start Engine with a Weak To Attach Jumper CablesTo Adjust Throttle Control Cable To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Adjust Carburetor Reassemble air cleaner. Closed for FullAcceleration Test Engine FuelsystemEngine OIL CylindersProblem Cause CorrectionTroubleshooting Chart Problem CauseTroubleshooting Chart Problem Cause CorrectionFast Tractor Model Number Schematic RelayTractor Model Number ElectricalTractor Model Number Electrical KEY Part NO. NO. Description109748X Relay Asm 181883 TachometerRound Tractor Model Number 917.275280 Chassis and Enclosures 37 178516X615 Fender Pnt 175278 43 136939 Bracket, Spnsn Front Lh74780716 177143 Rod By PassTractor Model Number Ground Drive PARt 122 72010520 Bolt Rdhd SQ 13764816-18unc x 2-1/2 127783 Pulley, Idler, Grooved 133 175468Stsrgn 20 177646X418 Boot, Steering Steering121232X ¢ap,Spind 23 152927 ScrewSpark Arrester KIT Tractor Model Number Lift Assembly 121006X Rod Asm.. Lever 138057180045 Shaft Asm., LiftVgt 155097 159189 Lever Asm., Lift Rh 123935XTractor Model Number Seat Assembly Pan, SeatNut, Lock 1/4 Lge Fig Gr 20 124238X Cap, SpringSeatTractor Model Number Decals Wheels and Tires2O13 Tractor Model Number Mower Deck Part DescriptionTractor Model Number 917.275280 TRANSAXLE-MODEL Number 178326 Spacer Assembly 169536 Odng 070 239 161127 Output Plate 122 178329 Brake Yoke Arm, Brake 169529ManifoId 139 161176 Washer 8od 265id 161142 203 178338 161155IzlU16 Kit, breather cover w/gasket 235011-S24-126-19-S 545016-SIGNITION/ELECTRICAL Iblower Housing and Baffles KEY Part NO. NO.DESCRIPTION KEY Part NO. noStarting Systemj ENGINECONTROLSs KEY Part Description KEY Part24-211-03-S Not IllustratedFuel Systemj Crankshaft Includes Gasket, exhaust Stud M8x1.25x3324-853-90-S Kit, carburetor w/gaskets Includes 12 -353-03-SPage Suggested Guide for Sighting Slopes for Safe Operation 800-LE-.FOYER Mc 888-SU4-1OGAR s@ Sea RoebuckandCo

917.27528 specifications

The Craftsman 917.27528 is a powerful and versatile lawn tractor designed to deliver superior performance and ease of use for homeowners and gardening enthusiasts. Known for its robust construction and a host of user-friendly features, this model has earned a reputation for reliability and efficiency in lawn care.

One of the standout features of the Craftsman 917.27528 is its 24 horsepower Briggs & Stratton engine. This powerful engine ensures smooth operation and is capable of handling even the most demanding mowing tasks. The engine is paired with a versatile automatic transmission, allowing for effortless speed adjustments while mowing or navigating through various terrains. This means users can easily transition from cutting grass to tackling hilly areas without sacrificing performance.

The lawn tractor is equipped with a 42-inch cutting deck, designed for optimal cutting efficiency. The deck features a three-blade system that provides a clean and even cut across various grass types. One of the highlights of this cutting deck is its adjustable height settings, allowing users to customize the cut based on their lawn's specific needs. In addition to traditional mowing, the Craftsman 917.27528 is compatible with a range of attachments, including mulch kits, baggers, and tow-behind devices, further enhancing its versatility.

Comfort is a priority in the design of the Craftsman 917.27528. The tractor features an ergonomic seat and easy-to-reach controls that make long mowing sessions much more enjoyable. The inclusion of a lap bar for steering provides better maneuverability and control, especially in tight spaces.

In terms of maintenance, the Craftsman 917.27528 stands out for its user-friendly design. Features such as an easy-access oil drain and a removable deck make routine maintenance tasks such as oil changes and blade sharpening straightforward, encouraging owners to keep their equipment in optimal condition.

Overall, the Craftsman 917.27528 combines powerful performance with practical features, making it an excellent choice for homeowners seeking a reliable lawn tractor. Its blend of technology, comfort, and adaptability helps ensure that mowing the lawn is a hassle-free experience. Whether for maintaining a small yard or tackling larger areas, this lawn tractor proves itself as a valuable asset in lawn care.
Top Page Image Contents