| | CAUTION:Blades are sharp. Protect | Blade |
| your hands with gloves and/or wrap |
| |
| blade with heavy | cloth. | | | |
| Check adjustment on right side of tractor. | |
| Position any blade so the tip is pointing | |
| straight forward. Measure distance "B" at | |
| front and | rear tip | of blade | | | |
| • | Before | making | any | necessary | adjust- | BOTH FRONT LINKS MUST BE EQUAL |
| | ments, check that both front links are |
| | IN LENGTH |
| | equal | in length. | | | |
| | | | | |
| • | If links | are not | equal | in | length, | adjust | |
| | one link to same length as other link. | |
| • To lower front of blade, loosen nut "C" | |
| | on both front links an equal number of _ | |
| | turns. | | | | | | |
| NOTE: Each full turn of nut "C" will | |
| change dim. "B" by approximately | 3/16". | |
| • When distance "B" is 1/8" to 1/2" lower | |
| | at front than rear, tighten nut "D" | |
| | against trunnion on both front links. | |
| • | To raise front | of blade, | loosen | nut "D" | Nut |
| | from trunnion on both front links. |
| | |
| | Tighten nut "C" on both front links an | |
| | equal | number | of turns. | | | |
•When distance "B" is 1/8" to 1/2" lower at front than rear, tighten nut "D"
| | against | trunnion | on | both front | links. | Front Plate | | | Trunnion | | |
| • Recheck side-to-side | | adjustment. | Assembly | | | | | | | | |
| TO REPLACE | MOWER | | DRIVE | BELT | 8. Remove | belt | from electric | clutch |
| MOWER | DRIVE BELT | | REMOVAL | pulley. | | | | | | | | |
| | 9. Remove belt from idler pulleys. |
| 1. Park tractor on a level surface. |
| 10.Check primary idler arm and two |
| | Engage | parking | brake. | | |
| | | | idlers to see that they rotate freely. |
| 2. Lower mower to its lowest position. |
| 11.Be sure spring is securely hooked to |
| 3. Disengage belt tension rod from lock |
| primary idler arm and spring arm. |
| | bracket. | | | | | | | | |
| | | | | | | | | | MOWER | DRIVE | BELT | INSTALLATION |
| | | | | | | | | | | |
| _ | CAUTION: | Rod | is spring | loaded. | 12.Install | belt | in | both | idlers. | | |
| Have a | firm | grip | on | rod | and release | 13.Install | new | belt onto | electric | clutch |
| slowly. | | | | | | | | | | pulley. | | | | | | | | |
| 4. Remove screws from R.H. | mandrel | 14.Carefully | roll | belt | into | upper | groove of |
| | cover | and | remove | cover. | | | R.H. | mandrel | pulley. | | | |
| 5. | Remove | any | dirt | or | grass | clippings | 15.Carefully | check | belt | routing | making |
| | which | may | have | accumulated | around | sure | belt | is in the grooves | correctly. |
| | mandrels | and | entire | upper | | deck | 16.Reconnect | | R.H. | suspension | | arm to |
| | surface. | | | | | | | | | rear | deck | | bracket | | with retainer spring. |
6.Disconnect R.H. suspension arm from 17.Reassemble R.H. mandrel cover.
rear deck bracket by removing | 18.Engage | belt tension rod by pushing |
retainer spring. | rod into | locking bracket. |
7.Carefully roll belt over the top of R.H. mandrel pulley.
Jcraftsmanj
Sears Craftsman Help Line
Sears
Service
Repair
Back Cover
II. Slope Operation
Safety
General Operation
Your
Do not
IV. Service
Mow up and down slopes, not across
IlL Children
Remove obstacles such as rocks, tree limbs, etc
Repair Agreement
Product Specifications
API-SF-SJ
Customer Responsibilities
To Remove Tractor from Carton
Check Battery
Install Seat
Unpack Carton
Check for Proper Position ALL Belts
Check Tire Pressure
Check Deck Levelness
Check Brake System
H L
Knowyour Tractor Your Tractor
Motion Drive Belt Tension
HOW to USE Your Tractor
To Operate Mower
To Adjust Gauge Wheels
To Operate On Hills Iicaution
Before Starting the Engine
Purgetransmssion
Automatic Transmission Warm UP
Mowing Tips
General Recommendations
Lubrication Chart
Before Each USE
Operator Presence System
Battery
Tires
Blade Care
Belts
Transaxle Cooling
Transaxle Pump Fluid
Engine Lubrication
Clean AIR INTAKE/COOLING Areas
To Service Cartridge
Clean AIR Screen
Cleaning
To Remove Mower
Bubble Between Lines m/b Bubble Level
To Level Mower Housing
Brake .. Left Hand Footrest Lift Link ANdustment
Length
Both Front Links Must be Equal
To Replace Mower Drive Belt
Arm
Electric
Pulley
To Replace Mower Blade SEC- Ondary Drive Belt
To Adjust Brake
To Adjust Attachment Clutch
To Replace Motion Drive Belt
To Adjust Steering Wheel ALIGN- Ment
Belt Installation
Transaxle Motion Control Lever Neutral Adjustment
Front Wheel TOE-IN Adjustment
To Start Engine with a Weak
Front Wheel Camber
To Remove Wheel for Repairs
To Attach Jumper Cables
Interlocks and Relays
To Adjust Throttle Control Cable
To Replace Headlight Bulb
To Replace Fuse
Reassemble air cleaner. Closed for Full
To Adjust Carburetor
Acceleration Test
Engine OIL
Engine
Fuelsystem
Cylinders
Problem
Cause Correction
Troubleshooting Chart
Problem Cause
Problem Cause Correction
Troubleshooting Chart
Fast
Tractor Model Number Schematic
Relay
Tractor Model Number
Electrical
KEY Part NO. NO. Description
Tractor Model Number Electrical
109748X Relay Asm 181883 TachometerRound
Tractor Model Number 917.275280 Chassis and Enclosures
74780716
37 178516X615 Fender Pnt 175278
43 136939 Bracket, Spnsn Front Lh
177143 Rod By Pass
Tractor Model Number Ground Drive
16-18unc x 2-1/2
PARt
122 72010520 Bolt Rdhd SQ 137648
127783 Pulley, Idler, Grooved 133 175468
Stsrgn
121232X ¢ap,Spind
20 177646X418 Boot, Steering
Steering
23 152927 Screw
Spark Arrester KIT
180045 Shaft Asm., LiftVgt 155097
Tractor Model Number Lift Assembly
121006X Rod Asm.. Lever 138057
159189 Lever Asm., Lift Rh 123935X
Nut, Lock 1/4 Lge Fig Gr
Tractor Model Number Seat Assembly
Pan, Seat
20 124238X Cap, SpringSeat
Wheels and Tires
Tractor Model Number Decals
2O13
Tractor Model Number Mower Deck
Part
Description
Tractor Model Number 917.275280 TRANSAXLE-MODEL Number
ManifoId 139 161176 Washer 8od 265id 161142
178326 Spacer Assembly 169536 Odng 070 239 161127 Output
Plate 122 178329 Brake Yoke Arm, Brake 169529
203 178338 161155
IzlU16
24-126-19-S
Kit, breather cover w/gasket
235011-S
545016-S
IGNITION/ELECTRICAL Iblower Housing and Baffles
KEY Part NO. NO.DESCRIPTION
KEY Part NO. no
Starting Systemj ENGINECONTROLSs
24-211-03-S
KEY Part Description
KEY Part
Not Illustrated
Fuel Systemj
24-853-90-S Kit, carburetor w/gaskets Includes
Crankshaft Includes
Gasket, exhaust Stud M8x1.25x33
12 -353-03-S
Page
Suggested Guide for Sighting Slopes for Safe Operation
888-SU4-1OGAR s
800-LE-.FOYER Mc
@ Sea RoebuckandCo