Craftsman 917.289283 owner manual Battery, Tires

Page 18

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as de- scribed, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE

SYSTEM

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

ROS "ON" Position Engine "ON" Position (Normal Operating)

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" posi- tion and the attachment clutch engaged, any attempt by the operator to drive in reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to drive in

reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be

sharp. Replace worn, bent or damaged blades.

_I, CAUTION: Use only a replacement

blade approved by the manufacturer of your tractor. Using a blade not approved

by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

2.Remove blade bolt by turning counter- clockwise.

3.Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Install and tighten blade bolt securely

(45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

 

Blade

Blade Bolt

Assembly

(Special)

 

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents CRRFrSMR# SEARS, Roebuckand CO., Hoffman ESTATES, IL 60179 U.S.ACraftsman Limited Warranty Days on BatteryTWO Years on Tractor General Operation Service Safe Handling of GasolineOn clothing, change cloth With Engine Running Product Specifications Repair ProtectionFor prices and additional information call Tools Required For AssemblyCH ECK Battery LabelCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper PositionH L I\1 Service REMINDER/HOUR Meter Know Your TractorTractor Engine HOW to USE Your TractorStopping To Move ForwardTo Adjust Gauge Wheels System CharacteristicsTo Adjust Mower Cutting Height To Operate MowerReverse Operation System ROS Using the Reverse Operation SystemTo Transport To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterTo Start Engine ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Schedule MaintenanceChart USE Hours Hours Rourb RourbBattery TiresTransaxle Pump Fluid Engine LubricationTo Service Cartridge Points CleaningPinch Deck Washout PortTo Install Mower To Remove Mower03042tex Precision SIDE-TO-SIDE Adjustment FRONT=TO=BACK Adjustm ENTVisual SIDE-TO-SIDE Adjustment To Level MowerBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt To Replace Motion Drive BeltTo Remove Wheel for Repairs To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT- TeryEngine Replacing BatteryTo Adjust Carburetor To Replace FuseTo Clean Battery and Termi Fuel SystemCylinders Problemcause CorrectionHard to start Clicks but Loss of powerCause Will notWill Poor grassWorking ChargeEngine OFF Cause CorrectionGai DOS Anos Para Tractores DiAS Para BATERiASDvertencia Funcionamiento GeneralAdvertencia Las instruccionesIII. Ninos IV. RemolquePage Responsabilidades DEL Cliente Especificaciones DELProducto Acuerdos DE Proteccion Para LA ReparacionLA Caja DE Carton Desempaque LA Caja DE Carton Herramientas Necesarias Para EL MontajePara Remover EL Tractor DE Antes DE Remover EL Tractor DE LA CorrederaRevision DE LA Nivelacion DEL Conjunto Revision DE LA Presion DE LAS LlantasRevision DEL Sistema DE Frenos Revision DE LA Posicion Adecuada DE Todas LAS Correas@@@ Familiaricese CON SU Tractor Palanca DE Mando CruceroPedal DE Marchaadelante Se utiliza Como Usar SU Tractor MientoPara Operar LA Segadora Utilizar EL Mando CruceroPara Ajustar LA Altura DE Corte DE LA Segadora Para Parar LAS Cuchillas DE LA SegaTransmisi6n Eric anchada #ansmisi6n Desenganchada Agregue Gasolina MotorPara Hacer Arrancar EL Motor Arranque CON Tiempo Templado 50F /1 0 C Y MASRgar LA Transmision Consejos Para SegarRecomendaciones Generales MantenimientoCadauso Antes DE Cada USOTractor Transeje MotorLUBRICAClON Limpieza DE LA Rejilla DE Aire LimpiezaFiltro DE Aire Filtro DE Combustible EN LineaPRECAUCIONi Puerto DE Lavado DE LA CubiertaInstale LA Segadora DE CespedPara Desmontar LA Cortadora Fije LOS Brazos DE Suspension03042tex Regulacion DE LA Precision DE Lado Para Nivelar LA SegadoraRegulacion Visual DE Lado a Lado Ajuste DE Delante a ATR,ASInstalacion DE LA Correa Para Cambiar LA Correa DE IMPULSI6N DE LA Cuchilla SegadoraRemocion DE LA Correa Montaje DE LA CorreaDAS Delanteras Controlar Y Ajustar EL FrenoControl DEL Freno Para Hacer Arrancar EL Motor CON UNA Baterja BajaPara Remover EL Conjunto DEL CA= Pota Y DEL Enrejado CarburadorOtros Sistema DE CombustibleAceite DEL Motor IDENTIFICACI6N DE Problemas Problema CausaIdentificackn DE Problemas Prdida deIdentificacion DE Problemas Causa$ O Needmore

917.289283, 917.28928 specifications

The Craftsman 917.289283 and 917.28928 are powerful lawn tractors designed for homeowners seeking exceptional performance, reliability, and innovation in their outdoor equipment. These models stand out in the market for their robust features and user-friendly technologies, making lawn care an efficient and enjoyable task.

One of the key features of the Craftsman 917.289283 and 917.28928 is their powerful engine. Equipped with a reliable engine, these tractors provide sufficient horsepower to tackle tough grass and uneven terrain. The engines deliver a strong torque, ensuring that homeowners can mow their lawns with confidence, regardless of the conditions.

Both models feature a 42-inch cutting deck, which strikes an ideal balance between maneuverability and cutting efficiency. The cutting deck design allows for a precise cut, ensuring that grass is trimmed evenly across various terrains. Additionally, the deck height can be easily adjusted to accommodate different grass lengths, providing versatility for lawn care.

The hydrostatic transmission featured in these tractors enhances driving experience, allowing for smooth acceleration and deceleration. Unlike traditional gear systems, the hydrostatic design enables users to control their speed with precision, making it easier to navigate around obstacles such as trees, flower beds, and garden decorations.

Another significant characteristic of the Craftsman 917.289283 and 917.28928 is their ergonomic design. The comfortable seat and steering wheel are adjustable, promoting ease of use for operators of all sizes. This level of comfort makes it easier for users to spend extended periods mowing without feeling fatigued.

Furthermore, the tractors come equipped with advanced safety features, including a safety switch under the seat that automatically shuts off the engine if the operator leaves the seat while the blades are engaged. This design element adds an extra layer of protection, particularly for households with children and pets.

In terms of maintenance, these Craftsman models are designed with convenience in mind. The easy-access engine and deck components allow users to perform routine maintenance tasks with minimal hassle. The onboard diagnostic system provides users with vital information regarding the tractor's performance, ensuring that it operates smoothly for years to come.

In conclusion, the Craftsman 917.289283 and 917.28928 empower homeowners with well-engineered lawn tractors that blend power, comfort, and safety. With their user-friendly features and dependable performance, these models are ideal choices for anyone looking to achieve a beautifully manicured lawn.
Top Page Image Contents