Manuals / HTC / Lawn and Garden / Lawn Mower

HTC LZC5225 / 965879601 Weak Battery, Jumper Cables, To remove cables, reverse order, Operation

Models: LZC5225 / 965879601 LZC5227 / 965879701 LZ30 / 968999776 LZC6130 / 965879801

1 76

Download 76 pages 22.6 Kb

Page 31

Weak Battery

OPERATION

Weak Battery

WARNING!

Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

IMPORTANT INFORMATION

Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles.

If “jumper cables” are used for emergency starting, follow this procedure:

Jumper Cables

•Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

• Connect one end of the BLACK cable to the	8011-642
NEGATIVE (-) terminal of the fully charged battery.	Jumper cable connection
NEGATIVE (-) terminal of the fully charged battery.
• Connect the other end of the BLACK cable to a
good CHASSIS GROUND on the mower with the
discharged battery, away from the fuel tank and
battery.

To remove cables, reverse order

•Remove BLACK cable first from chassis and then from the fully charged battery.

•Remove RED cable last from both batteries.

Husqvarna - 31

Image 31

HTC LZC5225 / 965879601 Weak Battery, Jumper Cables, To remove cables, reverse order, Operation, Important Information

Contents

LZC5227 Operator ManualEnglish LZC5225Page Contents English-4 Driving and Transport on Public Roads INTRODUCTIONCongratulations GeneralINTRODUCTION Good ServiceManufacturing Number Please have these available when ordering spare partsXxxx xxxxxx xxxxx xxxx xxxxxxxxx symbols and decalsIMPORTANT INFORMATION Manual symbols and decalsremove safety remove key beforeSafety Instructions SAFETYGeneral Operation Watch for traffic when operating near or crossing roadways SAFETYSlope Operation Personal Safety EquipmentSAFETY SAFETY ChildrenSAFETY Safe Handling of GasolineThe engine and the exhaust system become very hot during operation There is risk for burns if touchedUse protective glasses for maintenance work General MaintenanceSAFETY Use protective goggles SAFETYIMPORTANT INFORMATION if proper medical treatment is not administered immediatelyTransport SAFETYSAFETY Roll over Protection system ROPSSpark Arresters in effective working order by the operatorCONTROLS CONTROLS Motion Control Levers1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse CONTROLS Hour meterTracking knob Parking BrakeCONTROLS Blade switchIgnition Switch FusesCONTROLS RefuelingThe engine and the exhaust system, become very hot during operation Risk for burns if touchedLengthways adjustment Seat adjustment leverSeat Lock Fuel shut off valveMower Deck Lifting Lever USE FULL THROTTLE WHEN MOWINGChoke control Throttle controlTighten the valve moderately Cutting height lift pedalPump release valves Only rotate the valve ¼ to ½ turn to release the systemTo move forward and backward OPERATIONTraining SteeringStarting the Engine Roll bar and safety beltThe seat belt must be used when the roll bar is in upright position Before StartingDepress the control for disengaging the mower deck 4. Disengage the mower blades by depressing the blade switchOPERATION 6. Move the throttle to the middle positionSet the choke control OPERATION8. Open the valve for the selected fuel tank 9. Press in and turn the ignition key to the start positionOPERATION 11. Push the choke control in gradually when the engine has startedIMPORTANT INFORMATION OPERATION Weak BatteryJumper Cables To remove cables, reverse orderOPERATION The mower deck’s gauge wheels should be evenly adjustedEnsure that no one is near mower when engaging blade switch RunningIMPORTANT INFORMATION Operating on HillsStopping the Engine OPERATIONOPERATION Mowing Tipsthe parking brake activated No adjustments or maintenance to be carried out unlessMoving by Hand the engine stopped the ignition key removedDaily Before After maintenanceMaintenance Weekly At Maintenance interval least in hours once eachTurn the ignition switch to “OFF” position and remove the key Maintenance intervalBefore performing any service or adjustment checklist Place the Blade-switch in the disengaged positionReplacing battery BatteryAlways wear eye protection when around batteries Cleaning battery and terminalsmaintenance Safety SystemIgnition System Fitting the wrong spark plug type can damage the enginemaintenance Engine Cooling Air IntakeThrottle Cable Choke CableDust cap Air filter housing and filterDo not use compressed air to clean the air filter Air Filtermaintenance Engine Oil CoolerIMPORTANT INFORMATION Fuel Pump Air Filter Fuel Filtermaintenance maintenance Checking the V-beltsDeck belt To replace deck beltmaintenance Faulty adjustment of the parking brake can cause an accidentPump belt Tire Pressuresmaintenance Blade ReplacementCutter Blades Do not use a lower grade hardware than specifiedAdjusting Cutting Height Adjusting the Mower Deck2. Place the Blade switch in the disengaged position 3. Turn ignition switch to “OFF” position and remove the keyCaster Wheels CleaningUse protective glasses when cleaning and washing Removal and installation of caster wheelLubrication Schedule LUBRICATIONGeneral Hydraulic System, Oil Level Lubricating the CablesShaft Bushings and Linkage Following the Lubrication ScheduleLUBRICATION Engine OilChanging the Engine Oil Avoid skin contact wash with soap and water in case of spillsLUBRICATION Checking Oil LevelIMPORTANT INFORMATION Oil RecommendationsOil Type LUBRICATIONFront Wheel Bearings Mower Deck Height AdjusterThrottle and Choke Cables, Lever Bearings Front Wheel MountLUBRICATION Steering Control ShaftsMower Deck Struts Oil FilterProblem troubleshooting guideCause Problem troubleshooting guideCause a degreaser and warm water ServiceSTORAGE Winter StorageRIGHT MOTION WIRING DIAGRAMKEY SWITCH POSITIONS POSITION 1 - OFFEngine TECHNICAL DATALZC5225 LZC5227LZC5225 DimensionFrame TECHNICAL DATAEngine LZC6130LZ30 TECHNICAL DATALZ30 TECHNICAL DATADimension LZC6130U.S. Standard Hardware AccessoriesTorque Specifications HEX HEAD CAP SCREWSUSA requirements conformity certificatesCE requirements SECTION 3 - ITEMS NOT COVERED BY THIS WARRANTY WARRANTYSECTION 1 - LIMITED WARRANTY SECTION 2 - HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTYDate, mtr reading, stamp, sign SERVICE JOURNALDelivery Service ActionDate, mtr reading, stamp, sign After the First 5-8 HoursSERVICE JOURNAL Action5. Lubricate according to lubrication chart 25-Hour ServiceSERVICE JOURNAL 3. Check the tire pressures 4. Check battery with cables2. Clean/replace the air cleaner’s filter cartridge paper filter 50-Hour ServiceSERVICE JOURNAL 1. Perform the 25-hour service3. Change the engine oil filter 4. Clean/replace the spark plugs 100-Hour ServiceSERVICE JOURNAL 1. Perform the 25-hour service 2. Perform the 50-hour serviceDate, mtr reading, stamp, sign 300-Hour ServiceSERVICE JOURNAL ActionDate, mtr reading, stamp, sign At Least Once Each YearSERVICE JOURNAL Action74 - Husqvarna SERVICE JOURNALAction Date, mtr reading, stamp, signPage 06/01/09 P/N 115 138927 R01