Manuals / HTC / Lawn and Garden / Lawn Mower

HTC LZ30 / 968999776, LZC6130 / 965879801 manual Blade switch, Ignition Switch, Fuses, Controls

Models: LZC5225 / 965879601 LZC5227 / 965879701 LZ30 / 968999776 LZC6130 / 965879801

1 76

Download 76 pages 22.6 Kb

Page 21

Image 21

CONTROLS

Blade switch

To engage the mower deck, pull the blade switch knob out. The mower blades are disengaged when the knob is pressed down fully.

8011-510

Blade Switch

Ignition Switch

The ignition key is placed on the control panel and is used to start and stop the engine.

WARNING!

Do not run the starter for more than five seconds each time. If the engine does not start, wait 10 seconds before retrying.

Fuses

The fuses are located in a holder to the left of the hydraulic tank. They are flat pin fuses of the same type used in automobiles.

There are three fuses as well as a socket for one spare fuse.

Fuse ratings and functions:

•20 A, Primary fuse.

•7.5 A, Mower deck coupling.

•7.5 A, Accessory outlet.

•Socket for spare fuse.

8011-748

Ignition Switch

8011-746

Fuses

Husqvarna - 21

Page 21

Image 21

HTC LZ30 / 968999776, LZC6130 / 965879801, LZC5227 / 965879701 manual Blade switch, Ignition Switch, Fuses, Controls

Contents

English Operator ManualLZC5225 LZC5227Page Contents English-4 Congratulations INTRODUCTIONGeneral Driving and Transport on Public RoadsManufacturing Number Good ServicePlease have these available when ordering spare parts INTRODUCTIONsymbols and decals Xxxx xxxxxx xxxxx xxxx xxxxxxxxxIMPORTANT INFORMATION remove safety symbols and decalsremove key before ManualSAFETY Safety InstructionsGeneral Operation Watch for traffic when operating near or crossing roadways SAFETYPersonal Safety Equipment Slope OperationSAFETY SAFETY ChildrenThe engine and the exhaust system become very hot during operation Safe Handling of GasolineThere is risk for burns if touched SAFETYGeneral Maintenance Use protective glasses for maintenance workSAFETY Use protective goggles SAFETYTransport if proper medical treatment is not administered immediatelySAFETY IMPORTANT INFORMATIONSpark Arresters Roll over Protection system ROPSin effective working order by the operator SAFETYCONTROLS Motion Control Levers CONTROLS1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Tracking knob Hour meterParking Brake CONTROLSIgnition Switch Blade switchFuses CONTROLSThe engine and the exhaust system, become very hot during operation RefuelingRisk for burns if touched CONTROLSSeat Lock Seat adjustment leverFuel shut off valve Lengthways adjustmentChoke control USE FULL THROTTLE WHEN MOWINGThrottle control Mower Deck Lifting LeverPump release valves Cutting height lift pedalOnly rotate the valve ¼ to ½ turn to release the system Tighten the valve moderatelyTraining OPERATIONSteering To move forward and backwardThe seat belt must be used when the roll bar is in upright position Roll bar and safety beltBefore Starting Starting the EngineOPERATION 4. Disengage the mower blades by depressing the blade switch6. Move the throttle to the middle position Depress the control for disengaging the mower deck8. Open the valve for the selected fuel tank OPERATION9. Press in and turn the ignition key to the start position Set the choke control11. Push the choke control in gradually when the engine has started OPERATIONIMPORTANT INFORMATION Jumper Cables Weak BatteryTo remove cables, reverse order OPERATIONEnsure that no one is near mower when engaging blade switch The mower deck’s gauge wheels should be evenly adjustedRunning OPERATIONStopping the Engine Operating on HillsOPERATION IMPORTANT INFORMATIONOPERATION Mowing TipsMoving by Hand No adjustments or maintenance to be carried out unlessthe engine stopped the ignition key removed the parking brake activatedMaintenance maintenanceWeekly At Maintenance interval least in hours once each Daily Before AfterBefore performing any service or adjustment checklist Maintenance intervalPlace the Blade-switch in the disengaged position Turn the ignition switch to “OFF” position and remove the keyAlways wear eye protection when around batteries BatteryCleaning battery and terminals Replacing batteryIgnition System Safety SystemFitting the wrong spark plug type can damage the engine maintenanceThrottle Cable Engine Cooling Air IntakeChoke Cable maintenanceDo not use compressed air to clean the air filter Air filter housing and filterAir Filter Dust capEngine Oil Cooler maintenanceIMPORTANT INFORMATION Fuel Filter Fuel Pump Air Filtermaintenance Deck belt Checking the V-beltsTo replace deck belt maintenancePump belt Faulty adjustment of the parking brake can cause an accidentTire Pressures maintenanceCutter Blades Blade ReplacementDo not use a lower grade hardware than specified maintenance2. Place the Blade switch in the disengaged position Adjusting the Mower Deck3. Turn ignition switch to “OFF” position and remove the key Adjusting Cutting HeightUse protective glasses when cleaning and washing CleaningRemoval and installation of caster wheel Caster WheelsLUBRICATION Lubrication ScheduleGeneral Shaft Bushings and Linkage Lubricating the CablesFollowing the Lubrication Schedule Hydraulic System, Oil LevelChanging the Engine Oil Engine OilAvoid skin contact wash with soap and water in case of spills LUBRICATIONLUBRICATION Checking Oil LevelOil Type Oil RecommendationsLUBRICATION IMPORTANT INFORMATIONThrottle and Choke Cables, Lever Bearings Mower Deck Height AdjusterFront Wheel Mount Front Wheel BearingsMower Deck Struts Steering Control ShaftsOil Filter LUBRICATIONtroubleshooting guide ProblemCause troubleshooting guide ProblemCause STORAGE ServiceWinter Storage a degreaser and warm waterKEY SWITCH POSITIONS WIRING DIAGRAMPOSITION 1 - OFF RIGHT MOTIONLZC5225 TECHNICAL DATALZC5227 EngineFrame DimensionTECHNICAL DATA LZC5225LZ30 LZC6130TECHNICAL DATA EngineDimension TECHNICAL DATALZC6130 LZ30Torque Specifications AccessoriesHEX HEAD CAP SCREWS U.S. Standard Hardwareconformity certificates USA requirementsCE requirements SECTION 1 - LIMITED WARRANTY WARRANTYSECTION 2 - HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 3 - ITEMS NOT COVERED BY THIS WARRANTYDelivery Service SERVICE JOURNALAction Date, mtr reading, stamp, signSERVICE JOURNAL After the First 5-8 HoursAction Date, mtr reading, stamp, signSERVICE JOURNAL 25-Hour Service3. Check the tire pressures 4. Check battery with cables 5. Lubricate according to lubrication chartSERVICE JOURNAL 50-Hour Service1. Perform the 25-hour service 2. Clean/replace the air cleaner’s filter cartridge paper filterSERVICE JOURNAL 100-Hour Service1. Perform the 25-hour service 2. Perform the 50-hour service 3. Change the engine oil filter 4. Clean/replace the spark plugsSERVICE JOURNAL 300-Hour ServiceAction Date, mtr reading, stamp, signSERVICE JOURNAL At Least Once Each YearAction Date, mtr reading, stamp, signAction SERVICE JOURNALDate, mtr reading, stamp, sign 74 - HusqvarnaPage 06/01/09 P/N 115 138927 R01