Craftsman 917.2738 owner manual Automatictransmissionwarmup, Purge Transmission

Page 16

WARMWEATHERSTARTING(50° F and above)

8.When engine starts,slowlypush choke control in untilthe enginebegins to run smoothly.If the enginestarts to run roughly,pullthe chokecontrolout slightlyfor a fewsecondsand then continueto push the control in slowly.

•The attachmentsand grounddrive can now be used.If the engine does not acceptthe load, restartthe engine and

allow it to warm up for one minuteusing the chokeas describedabove.

COLD WEATHERSTARTING(50° F and below)

8.When engine starts,slowlypush choke control in untilthe enginebegins to run smoothly.Continueto pushthe choke control in smallsteps allowingthe en-

gine to accept small changes in speed and load, untilthe choke controlis fully in. If the engine starts to run roughly,

pull the chokecontrol out slightlyfor a fewsecondsand then continueto push the control in slowly.This may require an enginewarm-upperiod from several secondsto severalminutes,depending on the temperature.

AUTOMATICTRANSMISSIONWARMUP

Beforedriving the unit in cold weather, the transmissionshould be warmedup as follows:

1.Besure the tractor ison levelground.

2.Placethe motioncontrol leverin

neutral.Releasethe parkingbrake and letthe clutch/brakeslowlyreturn to operatingposition.

3.Allow one minutefor transmissionto warm up.Thiscan be doneduring the

enginewarm up period.

•The attachmentscan be used during the enginewarm-upperiod afterthe transmissionhas been warmedup and

mayrequirethe chokecontrol be pulled out slightly.

NOTE: If at a high altitude(above3000 feet) or in cold temperatures(below32 F) the carburetorfuel mixturemay needto be adjustedfor bestengineperformance sSee"TO ADJUSTCARBURETOR"in the erviceand Adjustmentssectionof this

manual).

PURGE TRANSMISSION

_CAUTION: Never engage or disengage freewheel lever while the engine is run- ning.

To ensure proper operation and per- formance, it is recommended that the

transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the trans- mission which may have developed during shipping of your tractor.

IMPORTANT: Should your transmission require removal for service or replace- ment, it should be purged after reinstall- ation before operating the tractor.

1.Place tractor safely on level surface with engine off and parking brake set.

2.Disengage transmission by placing freewheel control in '"transmission dis-

engaged" position (See "TO TRANS- PORT" in this section of manual).

3.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

4.Move motion control lever to full

forward position and hold for five (5) seconds. Move lever to full reverse

position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this step there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

5.Move motion control lever to neutral

(N)position. Shutoff engine and set parking brake.

6.Engage transmission by placing freewheel control in '"transmission

engaged" position (See "TO TRANS- PORT" in this section of manual).

7.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed.

With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

8.Slowly move motion control lever forward, after the tractor moves ap- proximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

Your transmission is now purged and ready for normal operation.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Jcriiftsmiinj Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationDo not IV. ServiceIII. Children Across Product Specifications Sears Installation ServiceCustomer Responsibilities UIRSteering Wheel KeysHowto SET UP Your Tractor Tools Required for AssemblyCheck Battery To Remove Tractor fromInstall Seat AdjInstall Mulcher Plate Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake System@@@@@ Know Your Tractor Discharging of battery Attachment Clutch Lever UsedMotion Control Lever Selects HOW to USE Your Tractor To Adjust Mower Cutting HeightTo SET Parking Brake To USE Throttle ControlTo Adjust Gauge Wheels To Operate MowerTo Operate On Hills Do not drive up or downTransmission Engaged Transmission Disengaged Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatictransmissionwarmup Purge TransmissionMulching Mowing Tips Mowing TipsImportant For best performance, keep Lubrication Chart General RecommendationsAsyoucomplete Before Each USETractor Operator Presence SystemBlade Removal To Sharpen BladeTo Clean Battery and Terminals Transaxle Pump FluidBelts Engine LubricationClean AIR Screen Clean AIR INTAKE/COOLING AreasAIR Filter Engine OIL FilterCleaning MufflerSpark Plugs IN-LINE Fuel FilterTo Install Mower To Level Mower Housing 0roundTo Check and Adjust Brake To Replace Mower Blade Drive BeltFront Wheel TOE-IN/CAMBER Transmission Removal ReplacementTo Remove Wheel for Repairs Replacing Battery To Start Engine with a Weak BAT- TE RYTo Attach Jumper Cables Interlocks and RelaysEngine CarburetorEngine BatteryFuel System Troubleshooting Chart ProblemLoss of power Will not start Hard to start Engine will not turn overExcessive VibrationEngine continues To run whenTroubleshooting Chart Problem Cause CorrectionTractor - Model Number Schematic Wiring Insulated ClipsTractor - Model Number ELECTRICAL22 Tractor - Model Number Electrical KEY Part DescriptionTractor - Model Number 917.273800 Chassis and Enclosures 206 Tractor - Model Number Ground Drive Link Transaxle Tractor - Model Number 917.273800 Steering Assembly Tractor - Model Number 917.273800 Steering Assembly Tractor - Model Number Tractor - Model Number Engine Tractor - Model Number Seat Assembly KEY Part Tractor - Model Number Decals Wheels &TIRESTractor - Model Number Lift Assembly 14//FF Tractor - Model Number Mower Deck165892 Mower Housing 165723 Illc 71idx1.15odx.030thk Flywheel f Control KEY NO. Partno IGNiTiON Coil Cylinder Head Labels Exhaust Pipe KEY NO. Part no Description Page Suggested Guide for Sighting Slopes for Safe Operation Your Home

917.2738 specifications

The Craftsman 917.2738 is a versatile and reliable lawn tractor designed for homeowners seeking an efficient solution for yard maintenance. This lawn tractor combines power, durability, and user-friendly features, making it an ideal choice for those with medium to large-sized lawns.

One of the standout features of the Craftsman 917.2738 is its robust engine. Powered by a reliable Briggs & Stratton engine, it provides the necessary torque and performance to tackle a variety of mowing tasks. The engine is designed for easy starting and dependable operation, ensuring that users spend less time worrying about maintenance and more time enjoying their landscaped surroundings.

The cutting deck of the Craftsman 917.2738 is another key feature, boasting a 42-inch size that allows for efficient mowing of large areas. The cutting height can be easily adjusted, offering users the flexibility to choose from multiple settings to suit their lawn’s needs. This feature not only enhances cutting performance but also promotes a healthier lawn by allowing for optimal grass growth.

Additionally, the tractor incorporates a hydrostatic transmission, which offers a smooth and intuitive driving experience. This technology removes the need for shifting gears, enabling operators to maintain control while navigating tricky terrain or tight spots. The responsive steering and maneuverability enhance the overall usability, making it easy for users to navigate around flower beds, trees, and other obstacles.

Another characteristic of the Craftsman 917.2738 is comfort and ergonomics. The tractor features a comfortable operator seat with ample padding, allowing users to mow for extended periods without discomfort. The easy-to-reach controls provide convenience and make operating the mower straightforward for both experienced gardeners and beginners alike.

Durability is an essential aspect of the Craftsman brand, and the 917.2738 lives up to this reputation with its sturdy chassis and high-quality materials. This ensures that the tractor can withstand regular wear and tear, making it a dependable choice for long-term lawn care.

Overall, the Craftsman 917.2738 combines powerful performance, innovative features, and comfort, making it a great investment for homeowners looking to efficiently maintain their lawns. With its balanced design and high-quality engineering, it stands out as a reliable workhorse in the realm of lawn tractors.
Top Page Image Contents