Craftsman 917.272057 To Adjust Gauge Wheels, To Operate Mower, To Operate on Hills, To Transport

Page 14

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches

during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass

over 6 inches in height should be mowed twice. Make the first cut

relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS

_ILCAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector

shield

in place.

 

Attachment

 

Clutch

Lever

Attachment

 

 

'erHigh

Position

_.

Position

Low

Position

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper

position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

1.Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in this section of manual).

2.With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/ 8 washer, and 3/8-16 Iocknut and tighten securely.

3.Repeat for opposite side installing

gauge wheel in same adjustment hole.

Gauge

Wheel

Mountin

Bracket

Locknut

3/8

Gauge Wheel

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

1.Select desired height of cut.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

Deflector

Shield

TO OPERATE ON HILLS

_)IbCAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to

brake position and engage parking brake.

•Move gearshift lever to lstgear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than

five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Lawn Tractor Sears Craftsman Help Line 5 am 5 pro, Mon- SatMaintenanceSchedule Parts Ordering Limited 90 DAY Warranty on BatteryDo not II. SlopeGeneral Operation IV. Service Ill. ChildrenWash hands after handling Filter Pints Filter 3.5 Pints Product SpecificationsRepair Agreement GAPWheel Insert Before Removingtractor Tools Required for AssemblyCheck Battery Attach Steering WheelTo Drivetractor OFF Skid See Operation section for location Install SeatPlace gearshift lever in neutral N position Check Tire Pressure ChecklistInstall Mulcher Plate Check Deck LevelnessH L Attachment Clutch Lever Used KnowyourtractorLift Parking Brake Lever Locks clutchTo SET Parking Brake To Adjust Mower Cutting HeightHowto Useyourtractor To USE Throttle ControlTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To TransportTowing Carts and Other Attachm Ents Before Starting the EngineTo Start Engine Check Engine OIL LevelMOWlNGTIPS Mulching MowingtipsTractor General Recommendations Lubrication ChartBefore Each USE PurposeTractor Belts Clean AIR ScreenClean AIR INTAKE/COOLING Areas Transaxle CoolingEngine OIL Filter AIR FilterSpark Plugs MufflerTractor To Remove Mower CleaningTo Install Mower Mower will be easier to remove fromFRONT-TO-BACK Adjustment To Level Mower HousingSIDE-TO-SIDE Adjustment Both Front Links Must be Equal LengthWith Parking Brake Engaged To Adjust BrakeTo Replace Mower Blade Drive Belt To Replace Motion Drive BeltTo Adjust Steering Wheel Align Ment Transaxle Gear Shift Lever Neutral AdjustmentTo Start Engine with a Weak Battery Front Wheel TOE-IN/CAMBERInterlocks and Relays Replacing BatteryTo Replace Headlight Bulb To Replace FuseEngine To Adjust Throttle Control CableTo Adjust Carburetor Acceleration TestEngine OIL BatteryFuel System CylindersCorrection Troubleshooting ChartProblemcause Vibration Throttle in Choke positionExcessive Engine ContinuesTroubleshooting Problem CauseTractor -- Model Number Schematic Ignition SwitchTractor - Model Number Electrical Tractor -- Model Number Electrical Bolt Hex Hd 1/4-20unc x 3/4Tractor - Model Number 917.272057 Chassis and Enclosures 206 Tractor --MODEL Number Chassis and Enclosures176554 Tractor - Model Number Ground Drive Tractor - Model Number Grounddrive Tractor - Model Number 917.272057 Steering Assembly 32 130465 Sod, Tie TRACTOR-- Model Number 917.272057 Steering Assembly139768 SteeringWheel 175131 Spark Arrester TRACTOR-- Model Number EngineOptional Equipment 137040 Line, FuelDescription Tractor - Model Number Seat AssemblyKEY Part Wheels & Tires KEY Part NO. NO. Description Decal, Replacement 146046Tractor -- Model Number Decals 65139Tractor - Model Number Lift Assembly 159460Tractor - Model Number Mower DeckTractor -- Model Number Mowerdeck KEY Part Description NO. no+--0 ID x.031W 772147 Transaxle Cover790079 780199Ylinder HEAD, Valve and Breather Exhaust KEY Part DescriptionValve 12-018-01-SAIR Intake J KEY Part NO. no PinionOIL PAN / Lubrication Kohler ENGINE-MODEL Number CV460, Type Number IncludesCrankshaftexhaust Fuel System 12-041-03-S Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours 6aJ.-11 p.m., 7daysaweek

917.272057 specifications

The Craftsman 917.272057 is a riding lawn mower designed for homeowners who seek an efficient and reliable solution for maintaining their lawns. With its powerful engine and advanced features, it stands out as a versatile tool for lawn care.

One of the main highlights of the Craftsman 917.272057 is its robust 19.5 HP Briggs & Stratton engine. This powerful engine not only provides ample power for cutting grass efficiently but also ensures smooth operation across various terrains. The automatic transmission further enhances the user experience by allowing for seamless speed adjustments without the need for manual shifting.

The mower showcases a cutting deck width of 42 inches, making it suitable for medium to large yards. This size strikes a balance between maneuverability and efficiency, enabling users to cover larger areas while navigating around obstacles such as trees and flower beds. The cutting height can be easily adjusted with a simple lever, allowing users to customize grass length according to their preferences and seasonal needs.

One of the standout features of the Craftsman 917.272057 is its mulching capability. The mower comes equipped with a mulching kit, which allows users to finely chop grass clippings, returning nutrients to the soil. This not only promotes a healthier lawn but also reduces the need for bagging or disposal of clippings.

The construction of the 917.272057 is designed with durability in mind. Its heavy-duty frame and reinforced cutting deck ensure longevity, even when used on varied landscapes. Furthermore, the comfortable high-back seat and easy-to-reach controls enhance operator comfort during longer mowing sessions.

In terms of maintenance, the Craftsman 917.272057 is user-friendly. Accessing the engine and other vital components for routine checks and servicing is straightforward, making it easier for owners to ensure optimal performance throughout the mowing season.

In summary, the Craftsman 917.272057 is a powerful and efficient riding lawn mower equipped with essential features that cater to the diverse needs of lawn care. With a robust engine, adjustable cutting deck, mulching capabilities, and user-friendly design, it offers a comprehensive solution for homeowners seeking an effective way to keep their lawns looking pristine. Whether tackling a small yard or a larger property, this mower combines performance, comfort, and durability, making it a valuable addition to any homeowner's gardening arsenal.
Top Page Image Contents