Craftsman 917.27242 Label, Battery Door, Install Seat, Sure the area in front of tractor is clear

Page 9

Label

Terminal

Battery

Door

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4.Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

5.Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

6.Lower seat into operating position and sit in seat.

7.Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

8.Get off seat without moving its adjusted position.

9.Raise seat and tighten adjustment knob securely.

,Seat

J

Seat Pan_

_

 

 

_"_"_

Shoulder

 

_::_3 _

Bort

Flat

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor

from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

1.Press lift lever plunger and raise attachment lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Place freewheel control in freewheel-

ing position to disengage transmis- sion (See "TO TRANSPORT" in the Operation section of this manual).

4.Roll tractor forward off skid.

5.Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See

Operation section for location and function of controls)

WARNING: Before starting, read,

understand and follow all instructions in

the Operation section of this manual, Be sure tractor is in a well-ventilated area, Be

sure the area in front of tractor is clear of

other people and objects.

1.Be sure all the above assembly steps have been completed.

2.Check engine oil level and fill fuel tank with gasoline.

3.Place freewheel control in "transmis- sion engaged" position.

4.Sit on seat in operating position, depress clutch/brake pedal and set the parking brake,

5.Place motion control lever in neutral

(N)position.

6.Press lift lever plunger and raise attachment lift lever to its highest position.

7.Start the engine. After engine has started, move throttle control to idle position.

8.Release parking brake.

9.Slowly move the motion control lever forward and slowly drive tractor off skid.

10.Apply brake to stop tractor, set parking brake and place motion control lever

in neutral position,

11 .Turn ignition key to "OFF" position. Continue with the instructions that follow.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Questions Lawn TractorLimited 90 DAY Warranty on Battery MaintenanceGeneral Operation Clean any oil or fuelStorage II. Slope OperationIII. Children IV. ServiceYou last saw them That may obscure visionPage Gallons Product SpecificationsUnleaded ForwardSlope Sheet Tools Required for Assembly HOW to SET UP Your Tractor Check BatteryCarton Unpack Carton Install Seat Battery DoorLabel Sure the area in front of tractor is clearInstall Mulcher Plate RlR N H L Throttle/Choke Knowyour TractorControl LiftLever Freewheel ControlTo Adjust Mower Cutting Height HOW to USE Your Tractor To SET Parking BrakeStopping EngineTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other ATTACH- MentsEngine in your tractor has been ADD GasolinePurge Transmission Automatic Transmission Warm UPMulching Mowing Tips Mowing TipsMaintenance Schedule Lubrication ChartGeneral Recommendations Once a year you should replaceOperator Presence System TiresBlade Care Blade RemovalTo Clean Battery and Terminals BatteryBelts Tranbaxle Cooling Transaxle Pump FluidClean AIR INTAKE/COOLING Areas Clean AIR ScreenTo Service PRE-CLEANER AIR FilterCleaning IN-LINE Fuel FilterFuel Filter To Remove Mower To Install MowerMove attachment lift lever forward to Retainer SpringMower to SIDE-TO-SIDE AdjustmentTo Replace Mower Blade Drive Belt Belt RemovalTo Adjust Brake Belt InstallationTransaxle Motion Control Lever Neutral Adjustment To Replace Motion Drive BeltTo Start Engine with a Weak Battery To Adjust Steering Wheel ALIGN- MentTransmission REMOVAL/REPLACE- Ment Front Wheel TOE-IN/CAMBEREngine To Adjust Carburetor AdjustingAcceleration Test Engineoil Engine Fuel SystemCylinders OtherProblem Troubleshooting ChartCause CorrectionFuel Loss of powerExcessive VibrationOFF Troubleshooting Chart ProblemcauseTractor - Model Number SchematicElectrical Tractor --MODEL NumberKEY Part Description Tractor -- Model NumberTractor - Model Number 917.272420 Chassis and Enclosures KEY Part Description TRACTOR--MODEL Number Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive Inches 1 inch= 25.4 mm TRACTOR--MODELNUMBER917.272420 Steeringassembly TRACTOR- -MODELNUMBER917.272420 Steeringassembly Optional Equipment r Spark Arrester KEY Part NO. NO.DESCRIPTION TRACTOR-- ModelnumberTRACTOR--MODEL Number Seat Assembly Wheels & Tires DecalsTractor - Model Number Liftassembly Washer 21/32 x 1 x21 Gauge 120183X Beadng, Nylon TRACTOR- Model Number Lift AssemblyTractor --MODEL Number Mower Deck O3J72140614 Ill Assembly 170408 Crankcase I CARTER-MOTEUR KEY Part Oescription Arede ARRIVSEJ1 AIR INTAKE/FILTRATION Engine Controls OIL PAN/LUBRICATION UEL DE LE Systemei Crankshaft KEY Part Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Part 80o-366-7278888-SU.HOGARsM

917.27242 specifications

The Craftsman 917.27242 is a high-performance riding lawn mower that delivers the power and precision needed for effective lawn maintenance. Designed for efficiency and ease of use, this model is ideal for homeowners with medium to large-sized lawns.

One of the standout features of the Craftsman 917.27242 is its robust 24 HP Kohler engine. This powerful engine ensures reliable starting and strong performance, making mowing tasks quicker and more efficient. Coupled with a hydrostatic transmission, the mower offers seamless speed adjustments without the need for shifting gears, allowing users to maneuver easily across various terrains.

The mower is equipped with a 42-inch cutting deck, which strikes a balance between size and maneuverability. This deck size is suitable for efficiently tackling both small and large areas while still being able to navigate tighter spaces like flower beds or around trees. The cutting height can be easily adjusted from 1.5 to 4 inches, enabling customization based on grass type and seasonal requirements.

In terms of technology, the Craftsman 917.27242 features an innovative, ergonomic design that enhances user comfort. The seat is adjustable, ensuring a relaxed riding position for operators of different heights. Additionally, the intuitive control panel simplifies operation, incorporating easily accessible controls for starting, cutting height adjustments, and more.

Safety is a priority in the Craftsman design. The mower includes features such as a blade brake that automatically engages when the operator leaves the seat, ensuring that the blades stop immediately when needed. This prevents accidents and adds a layer of security, especially when users need to dismount.

Moreover, the Craftsman 917.27242 is compatible with various attachments, making it a versatile choice. Beyond just mowing, attachments like baggers, mulch kits, and even snow plows can transform this machine for year-round use.

Overall, the Craftsman 917.27242 combines power, efficiency, and user-friendly features to provide an exceptional mowing experience. Suitable for both residential and light commercial use, it stands out in a competitive market, delivering reliability and high-quality performance that homeowners can depend on for maintaining their lawns.
Top Page Image Contents