Craftsman 917.27242 Transmission REMOVAL/REPLACE- Ment, To Adjust Steering Wheel ALIGN- Ment

Page 26

3.Tighten adjustment bolt securely.

4.Start engine and test.

5.If tractor still creeps, repeat above steps until satisfied.

Washers

Retaining_ f_'_

Ring\ I\ _'_"_'_'_

Axle \ I \ II/1{_ llll

Motion Control

Lever

Neutral Lock Gate

TRANSMISSION REMOVAL/REPLACE- MENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and

before operating the tractor. See "PURGE TRANSMISSION" in the

Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steedng wheel croeebam are not horizontal (left to right) when wheels are positioned straight forward, remove steedn_ wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-inand camber are

not adjustable on your tractor. If damage has occurred to affect the front wheel toe-

in or camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

z't

4UICAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and

smoking materials away from batteries. Always wear eye protection when mound batter;_=s.

If your battery is too weak to start the engine, it should be recharged. (See "BATFERY"in the MAINTENANCE section of this manual).

ff"jumper cables" are used for emergency starting, follow this procedure:

IMPORTANT: Your tractor is equi_

with a

12 volt negative grounded system.The other vehical must also be a 12 volt negative grounded system. Do not use your tractor battery to start other vehicles.

TO ATI'ACHJUMPER CABLES -

1.Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

3.Connect the other end of the BLACK

cable to good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

Positive Terminal

Negative Terminal

Cables

PositiveBattery

26Terminal

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Lawn Tractor QuestionsMaintenance Limited 90 DAY Warranty on BatteryStorage Clean any oil or fuelGeneral Operation II. Slope OperationYou last saw them IV. ServiceIII. Children That may obscure visionPage Unleaded Product SpecificationsGallons ForwardSlope Sheet Carton Unpack Carton Tools Required for AssemblyHOW to SET UP Your Tractor Check Battery Label Battery DoorInstall Seat Sure the area in front of tractor is clearInstall Mulcher Plate RlR N H L Control LiftLever Knowyour TractorThrottle/Choke Freewheel ControlStopping HOW to USE Your Tractor To SET Parking BrakeTo Adjust Mower Cutting Height EngineTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To TransportEngine in your tractor has been Towing Carts and Other ATTACH- MentsBefore Starting the Engine Check Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Purge TransmissionMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartMaintenance Schedule Once a year you should replaceBlade Care TiresOperator Presence System Blade RemovalBelts BatteryTo Clean Battery and Terminals Tranbaxle Cooling Transaxle Pump FluidTo Service PRE-CLEANER Clean AIR ScreenClean AIR INTAKE/COOLING Areas AIR FilterFuel Filter CleaningIN-LINE Fuel Filter Move attachment lift lever forward to To Install MowerTo Remove Mower Retainer SpringTo Replace Mower Blade Drive Belt SIDE-TO-SIDE AdjustmentMower to Belt RemovalTransaxle Motion Control Lever Neutral Adjustment Belt InstallationTo Adjust Brake To Replace Motion Drive BeltTransmission REMOVAL/REPLACE- Ment To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery Front Wheel TOE-IN/CAMBEREngine Acceleration Test To Adjust CarburetorAdjusting Cylinders Engine Fuel SystemEngineoil OtherCause Troubleshooting ChartProblem CorrectionExcessive Loss of powerFuel VibrationTroubleshooting Chart Problemcause OFFSchematic Tractor - Model NumberTractor --MODEL Number ElectricalTractor -- Model Number KEY Part DescriptionTractor - Model Number 917.272420 Chassis and Enclosures TRACTOR--MODEL Number Chassis and Enclosures KEY Part DescriptionTRACTOR--MODEL Number Ground Drive Inches 1 inch= 25.4 mm TRACTOR--MODELNUMBER917.272420 Steeringassembly TRACTOR- -MODELNUMBER917.272420 Steeringassembly Optional Equipment r Spark Arrester TRACTOR-- Modelnumber KEY Part NO. NO.DESCRIPTIONTRACTOR--MODEL Number Seat Assembly Decals Wheels & TiresTractor - Model Number Liftassembly TRACTOR- Model Number Lift Assembly Washer 21/32 x 1 x21 Gauge 120183X Beadng, NylonO3J Tractor --MODEL Number Mower Deck72140614 Ill Assembly 170408 Crankcase I CARTER-MOTEUR KEY Part Oescription Arede ARRIVSEJ1 AIR INTAKE/FILTRATION Engine Controls OIL PAN/LUBRICATION UEL DE LE Systemei Crankshaft KEY Part Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation 888-SU.HOGARsM Part80o-366-7278

917.27242 specifications

The Craftsman 917.27242 is a high-performance riding lawn mower that delivers the power and precision needed for effective lawn maintenance. Designed for efficiency and ease of use, this model is ideal for homeowners with medium to large-sized lawns.

One of the standout features of the Craftsman 917.27242 is its robust 24 HP Kohler engine. This powerful engine ensures reliable starting and strong performance, making mowing tasks quicker and more efficient. Coupled with a hydrostatic transmission, the mower offers seamless speed adjustments without the need for shifting gears, allowing users to maneuver easily across various terrains.

The mower is equipped with a 42-inch cutting deck, which strikes a balance between size and maneuverability. This deck size is suitable for efficiently tackling both small and large areas while still being able to navigate tighter spaces like flower beds or around trees. The cutting height can be easily adjusted from 1.5 to 4 inches, enabling customization based on grass type and seasonal requirements.

In terms of technology, the Craftsman 917.27242 features an innovative, ergonomic design that enhances user comfort. The seat is adjustable, ensuring a relaxed riding position for operators of different heights. Additionally, the intuitive control panel simplifies operation, incorporating easily accessible controls for starting, cutting height adjustments, and more.

Safety is a priority in the Craftsman design. The mower includes features such as a blade brake that automatically engages when the operator leaves the seat, ensuring that the blades stop immediately when needed. This prevents accidents and adds a layer of security, especially when users need to dismount.

Moreover, the Craftsman 917.27242 is compatible with various attachments, making it a versatile choice. Beyond just mowing, attachments like baggers, mulch kits, and even snow plows can transform this machine for year-round use.

Overall, the Craftsman 917.27242 combines power, efficiency, and user-friendly features to provide an exceptional mowing experience. Suitable for both residential and light commercial use, it stands out in a competitive market, delivering reliability and high-quality performance that homeowners can depend on for maintaining their lawns.
Top Page Image Contents